metabo HPT CV 18DA Cordless Multi Tool Instruction Manual

Model
CV 18DA
Cordless Multi Tool

CV 18DA Cordless Multi Tool

SAFETY INSTRUCTIONS AND INSTRUCTION MANUAL

WARNING
IMPROPER OR UNSAFE use of this power tool can result in death or serious bodily injury!
This manual contains important information about product safety. Please read and understand this manual BEFORE operating the power tool. Please keep this manual available for other users and owners before they use the power tool. This manual should be stored in safe place.

IMPORTANT SAFETY INSTRUCTIONS

Read and understand all of the safety precautions, warnings and operating instructions in the Instruction Manual before operating or maintaining this power tool.
Most accidents that result from power tool operation and maintenance are caused by the failure to observe basic safety rules or precautions. An accident can often be avoided by recognizing a potentially hazardous situation before it occurs, and by observing appropriate safety procedures.
Basic safety precautions are outlined in the “SAFETY” section of this Instruction Manual and in the sections which contain the operation and maintenance instructions.
Hazards that must be avoided to prevent bodily injury or machine damage are identified by WARNINGS on the power tool and in this Instruction Manual.
NEVER use this power tool in a manner that has not been specifically recommended by metabo HPT.

MEANINGS OF SIGNAL WORDS
WARNING indicates a potentially hazardous situations which, if ignored, could result in death or serious injury.
CAUTION indicates a potentially hazardous situations which, if not avoided, may result in minor or moderate injury, or may cause machine damage.
NOTE emphasizes essential information.

SAFETY

GENERAL POWER TOOL SAFETY WARNINGS

WARNING
Read all safety warnings, instructions, illustrations and specifications provided with this power tool.
Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.

1. Work area safety
   a) Keep work area clean and well lit.
   Cluttered or dark areas invite accidents.
   b) Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust.
   Power tools create sparks which may ignite the dust or fumes.
   c) Keep children and bystanders away while operating a power tool.
   Distractions can cause you to lose control.

2. Electrical safety
   a) Power tool plugs must match the outlet. Never modify the plug in any way.
   Do not use any adapter plugs with earthed (grounded) power tools.
   Unmodified plugs and matching outlets will reduce risk of electric shock.
   b) Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators.
   There is an increased risk of electric shock if your body is earthed or grounded.
   c) Do not expose power tools to rain or wet conditions.
   Water entering a power tool will increase the risk of electric shock.
   d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool.
   Keep cord away from heat, oil, sharp edges or moving parts.
   Damaged or entangled cords increase the risk of electric shock.
   e) When operating a power tool outdoors, use an extension cord suitable for outdoor use.
   Use of a cord suitable for outdoor use reduces the risk of electric shock.
   f) If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply.
   Use of an RCD reduces the risk of electric shock.

3. Personal safety
   a) Stay alert, watch what you are doing and use common sense when operating a power tool.
   Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication.
   A moment of inattention while operating power tools may result in serious personal injury.
   b) Use personal protective equipment. Always wear eye protection.
   Protective equipment such as a dust mask, non- skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.
   c) Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool.
   Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents.
   d) Remove any adjusting key or wrench before turning the power tool on.
   A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
   e) Do not overreach. Keep proper footing and balance at all times.
   This enables better control of the power tool in unexpected situations.
   f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair and clothing away from moving parts.
   Loose clothes, jewellery or long hair can be caught in moving parts.
   g) If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used.
   Use of dust collection can reduce dust-related hazards.
   h) Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool safety principles.
   A careless action can cause severe injury within a fraction of a second.

4. Power tool use and care
   a) Do not force the power tool. Use the correct power tool for your application.
   The correct power tool will do the job better and safer at the rate for which it was designed.
   b) Do not use the power tool if the switch does not turn it on and off.
   Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
   c) Disconnect the plug from the power source and/or remove the battery pack, if detachable, from the power tool before making any adjustments, changing accessories, or storing power tools.
   Such preventive safety measures reduce the risk of starting the power tool accidentally.
   d) Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool.
   Power tools are dangerous in the hands of untrained users.
   e) Maintain power tools and accessories.
   Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power toolʼs operation.
   If damaged, have the power tool repaired before use.
   Many accidents are caused by poorly maintained power tools.
   f) Keep cutting tools sharp and clean.
   Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
   g) Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed.
   Use of the power tool for operations different from those intended could result in a hazardous situation.
   h) Keep handles and grasping surfaces dry, clean and free from oil and grease.
   Slippery handles and grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.

5. Battery tool use and care
   a) Recharge only with the charger specified by the manufacturer.
   A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.
   b) Use power tools only with specifically designated battery packs.
   Use of any other battery packs may create a risk of injury and fire.
   c) When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another.
   Shorting the battery terminals together may cause burns or a fire.
   d) Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help.
   Liquid ejected from the battery may cause irritation or burns.
   e) Do not use a battery pack or tool that is damaged or modified.
   Damaged or modified batteries may exhibit unpredictable behaviour resulting in fire, explosion or risk of injury.
   f) Do not expose a battery pack or tool to fire or excessive temperature.
   Exposure to fire or temperature above 265°F may cause explosion.
   g) Follow all charging instructions and do not charge the battery pack or tool outside the temperature range specified in the instructions.
   Charging improperly or at temperatures outside the specified range may damage the battery and increase the risk of fire.

6. Service
   a) Have your power tool serviced by a qualified repair person using only identical replacement parts.
   This will ensure that the safety of the power tool is maintained.
   b) Never service damaged battery packs.
   Service of battery packs should only be performed by the manufacturer or authorized service providers.

WARNING
To reduce the risk of injury, user must read instruction manual.

SPECIFIC SAFETY RULES AND SYMBOLS

1. Hold power tool by insulated gripping surfaces, when performing an operation where the cutting accessory may contact hidden wiring.
   Cutting accessory contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.

2. Do not use this tool in wet applications.
   Water or moisture entering the tool could give the operator an electric shock.

3. Always hold the tool firmly with one hand on housing (Fig. 1). Do not touch the metal part.

4. Make sure that the area to be cut is absolutely free of any hidden obstructions including electrical wiring, water, or gas pipes. Cutting into the aforementioned may result in electric shock or short circuit, gas leak or other hazards that can cause serious accidents or injuries.

5. Setting up and checking the work environment.
   Check if the work environment is suitable by following the precaution.

6. Dust particles such as silica or asbestos are hazardous to your health. When working with materials containing these components, take appropriate dust-proofing measures.

7. Use clamps or another practical way to secure and support the workpiece to a stable platform.
   Holding the workpiece by hand or against your body leaves it unstable and may lead to loss of control.

8. ALWAYS wear ear protectors when using the tool for extended periods.
   Prolonged exposure to high intensity noise can cause hearing loss.
   

9. NEVER touch the application tool with bare hands after operation.

10. Because the cordless multi tool operates by battery power, be aware of the fact that it can begin to operate at any time.

11. When working at elevated locations, clear the area of all other people and be aware of conditions below you.

12. NEVER touch moving parts.
    NEVER place your hands, fingers or other body parts near the tool’s moving parts.

13. NEVER operate without all guards in place.
    NEVER operate this tool without all guards or safety features in place and in proper working order. If maintenance or servicing requires the removal of a guard or safety feature, be sure to replace the guard or safety feature before resuming operation of the tool.

14. Use right tool.
    Don’t force small tool or attachment to do the job of a heavy-duty tool.
    Don’t use tool for purpose not intended —for example — don’t use multi tool for cutting tree limbs or logs.

15. NEVER use a power tool for applications other than those specified.
    NEVER use a power tool for applications other than those specified in the instruction manual.

16. Handle tool correctly.
    Operate the tool according to the instructions provided herein. Do not drop or throw the tool.
    NEVER allow the tool to be operated by children, individuals unfamiliar with its operation or unauthorized personnel.

17. Keep all screws, bolts and covers tightly in place.
    Keep all screws, bolts, and plates tightly mounted.
    Check their condition periodically.

18. Do not use power tools if the plastic housing or handle is cracked.
    Cracks in the tool’s housing or handle can lead to electric shock. Such tools should not be used until repaired.

19. Application tools and accessories must be securely mounted to the tool.
    Prevent potential injuries to yourself or others.
    Application tools, cutting implements and accessories which have been mounted to the tool should be secure and tight.

20. Keep motor air vent clean.
    The tool’s motor air vent must be kept clean so that air can freely flow at all times. Check for dust build-up frequently.

21. NEVER use a tool which is defective or operating abnormally.
    If the tool appears to be operating unusually, making strange noises, or otherwise appears defective, stop using it immediately and arrange for repairs by a metabo HPT authorized service center.

22. NEVER leave tool running unattended. Turn power off.
    Don’t leave tool until it comes to a complete stop.

23. Carefully handle power tools.
    Should a power tool be dropped or struck against hard materials inadvertently, it may be deformed, cracked, or damaged.

24. Do not wipe plastic parts with solvent.
    Solvents such as gasoline, thinner benzine, carbon tetrachloride, and alcohol may damage and crack plastic parts. Do not wipe them with such solvents.
    Wipe plastic parts with a soft cloth lightly dampened with soapy water and dry thoroughly.

25. Always wear eye protection that meets the requirement of the latest revision of ANSI Standard Z87.1.

26. ALWAYS wear a mask or respirator to protect yourself from dust or potentially harmful particles generated during operation.

27. ALWAYS firmly grip the handle while operating.

28. ALWAYS be careful with buried object such as an underground wiring.
    Touching these active wiring or electric cable with this tool, you may receive an electric shock.
    Confirm if there are any buried object such as electric cable within the wall, floor or ceiling where you are going to operate here after.

29. Working with metal can cause sparks. Make sure there are no flammable and combustible materials in the vicinity and that they are stored in a safe location.

30. The motor may stop in the event the tool is overloaded. In this should occur, release the tool’s switch and eliminate the cause of the overload.

31. Do not leave the tool running unattended on the floor, table or other locations. Doing so may result in injury.

32. If the application tool seems to be loose or uneven after attaching it to the unit, re-attach the tool.
    Operating the unit with a loose or uneven application tool may result in injury.

33. Do not use the product if the tool or the battery terminals (battery mount) are deformed.
    Installing the battery could cause a short circuit that could result in smoke emission or ignition.

34. Keep the tool’s terminals (battery mount) free of swarf and dust.
    ○ Prior to use, make sure that swarf and dust have not collected in the area of the terminals.
    ○ During use, try to avoid swarf or dust on the tool from falling on the battery.
    ○ When suspending operation or after use, do not leave the tool in an area where it may be exposed to falling swarf or dust.
    Doing so could cause a short circuit that could result in smoke emission or ignition.

35. Always use the tool and battery at temperatures between 23°F (-5°C) and 104°F (40°C).

36. Definitions for symbols used on this tool

V……………………………………………………………….. volts
**** …………………………………………………. direct current
n0 ………………………………………………… no load speed
—/min…………. revolutions or reciprocation per minute
Hz …………………………………………………………….. hertz
A …………………………………………………………. amperes

IMPORTANT SAFETY INSTRUCTIONS FOR BATTERY CHARGER

WARNING
Death or serious bodily injury could result from improper or unsafe use of battery chargers. To avoid these risks, follow these basic safety instructions:

READ ALL INSTRUCTIONS

1. This manual contains important safety and operating instructions for battery charger Model UC18YFSL.
2. Before using battery charger, read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) product using battery.
3. To reduce risk of injury, charge metabo HPT rechargeable battery types BSL18 series and multi volt series. Other type of batteries may burst causing personal injury and damage.
4. Use of an attachment not recommended or sold by the battery charger manufacturer may result in a risk of fire, electric shock, or injury to persons.
5. To reduce risk of damage to electric plug and cord, pull by plug when disconnecting battery charger.
6. Make sure cord is located so that it will not be stepped on, tripped over, or otherwise subjected to damage or stress.
7. An extension cord should not be used unless absolutely necessary. Use of improper extension cord could result in a risk of fire and electric shock.
   If extension cord must be used make sure:
   a. That blades of extension cord are the same number, size, and shape as those of plug on battery charger:
   b. That extension cord is properly wired and in good electrical condition; and
   c. That wire size is large enough for AC ampere rating of battery charger as specified in Table 1.
   Table 1: RECOMMENDED MINIMUM AWG SIZE FOR EXTENSION CORDS FOR BATTERY CHARGERSAC Input Rating
   Amperes *1| AWG Size of Cord
   ---|---
   Equal to or greater than| but less than| Length of Cord, Feet (Meter)
   25 (7.5)| 50 (15)| 100 (30)| 150 (45)
   0| 2| 18| 18| 18| 16
   2| 3| 18| 18| 16| 14
   3| 4| 18| 18| 16| 14

*1 If the input rating of a battery charger is given in watts rather than in amperes, the corresponding ampere rating is to be determined by dividing the wattage rating by the voltage rating–for example:

8. Do not operate battery charger with damaged cord or plug-replace them immediately.
9. Do not operate battery charger if it has received a sharp blow, been dropped, or otherwise damaged in any way; take it to a qualified serviceman.
10. Do not disassemble battery charger; take it to a qualified serviceman when service or repair is required. Incorrect reassembly may result in a risk of electric shock or fire.
11. To reduce risk of electric shock, unplug charger from receptacle before attempting any maintenance or cleaning. Removing the battery will not reduce this risk.

IMPORTANT SAFETY INSTRUCTIONS FOR USE OF THE BATTERY AND BATTERY CHARGER

You must charge the battery before you can use the power tool. Before using the model UC18YFSL battery charger, be sure to read all instructions and cautionary statements on it, the battery and in this manual.

WARNING
USE ONLY metabo HPT BATTERIES. OTHER MODELS OF BATTERIES MAY BURST AND CAUSE INJURY!
Follow these instructions to avoid the risk of injury:

WARNING
Improper use of the battery or battery charger can lead to serious injury. To avoid these injuries:

1. NEVER disassemble the battery.
2. NEVER incinerate the battery, even if it is damaged or is completely worn out. The battery can explode in a fire.
3. NEVER short-circuit the battery.
4. NEVER insert any objects into the battery charger’s air vents. Electric shock or damage to the battery charger may result.
5. NEVER charge outdoors. Keep the battery away from direct sunlight and use only where there is low humidity and good ventilation.
6. NEVER charge when the temperature is below 32°F (0°C) or above 104°F (40°C).
7. NEVER connect two battery chargers together.
8. NEVER insert foreign objects into the hole for the battery or the battery charger.
9. NEVER use a booster transformer when charging.
10. NEVER use DC power to charge.
11. NEVER store the battery or battery charger in places where the temperature may reach or exceed 104°F (40°C) such as inside metal box or car.
12. NEVER expose the battery or battery charger to rain or wet conditions.
13. ALWAYS operate charger on standard household electrical power (120 volts). Using the charger on any other voltage may overheat and damage the charger.
14. ALWAYS wait at least 15 minutes between charges to avoid overheating the charger.
15. ALWAYS disconnect the power cord from its receptacle when the charger is not in use.

CAUTION ON LITHIUM-ION BATTERY

To extend the lifetime, the lithium-ion battery equips with the protection function to stop the output.
In the cases of 1 to 3 described below, when using this product, even if you are pulling the switch, the motor may stop. This is not the trouble but the result of protection function.

1. When the battery power remaining runs out, the motor stops.
   In such case, charge it up immediately.

2. If the tool is overloaded, the motor may stop. In this case, release the switch of tool and eliminate causes of overloading. After that, you can use it again.

3. If the battery is overheated under overload work, the battery power may stop.
   In this case, stop using the battery and let the battery cool. After that, you can use it again.

Furthermore, please heed the following warning and caution.

WARNING
In order to prevent any battery leakage, heat generation, smoke emission, explosion and ignition beforehand, please be sure to heed the following precautions.

1. Make sure that swarf and dust do not collect on the battery.
   ○ During work make sure that swarf and dust do not fall on the battery.
   ○ Make sure that any swarf and dust falling on the power tool during work do not collect on the battery.
   ○ Do not store an unused battery in a location exposed to swarf and dust.
   ○ Before storing a battery, remove any swarf and dust that may adhere to it and do not store it together with metal parts (screws, nails, etc.).

2. Do not pierce battery with a sharp object such as a nail, strike with a hammer, step on, throw or subject the battery to severe physical shock.

3. Do not use an apparently damaged or deformed battery.

4. Do not use the battery for a purpose other than those specified.

5. If the battery charging fails to complete even when a specified recharging time has elapsed, immediately stop further recharging.

6. Do not put or subject the battery to high temperatures or high pressure such as into a microwave oven, dryer, or high pressure container.

7. Keep away from fire immediately when leakage or foul odor are detected.

8. Do not use in a location where strong static electricity generates.

9. If there is battery leakage, foul odor, heat generated, discolored or deformed, or in any way appears abnormal during use, recharging or storage, immediately remove it from the equipment or battery charger, and stop use.

10. Do not immerse the battery or allow any fluids to flow inside. Conductive liquid ingress, such as water, can cause damage resulting in fire or explosion. Store your battery in a cool, dry place, away from combustible and flammable items. Corrosive gas atmospheres must be avoided.

CAUTION

1. If liquid leaking from the battery gets into your eyes, do not rub your eyes and wash them well with fresh clean water such as tap water and contact a doctor immediately.
   If left untreated, the liquid may cause eye-problems.

2. If liquid leaks onto your skin or clothes, wash well with clean water such as tap water immediately.
   There is a possibility that this can cause skin irritation.

3. If you find rust, foul odor, overheating, discolor, deformation, and/or other irregularities when using the battery for the first time, do not use and return it to your supplier or vendor.

WARNING
If an electrically conductive foreign object enters the terminals of the lithium ion battery, a short-circuit may occur resulting in the risk of fire. Please observe the following matters when storing the battery.

• Do not place electrically conductive cuttings, nails, steel wire, copper wire or other wire in the storage case.
• Either install the battery in the power tool or store by securely pressing into the battery cover until the ventilation holes are concealed to prevent short-circuits (See Fig. 4).

REGARDING LITHIUM-ION BATTERY TRANSPORTATION
When transporting a lithium-ion battery, please observe the following precautions.

WARNING
Notify the transporting company that a package contains a lithium-ion battery, inform the company of its power output and follow the instructions of the transportation company when arranging transport.

• Lithium-ion batteries that exceed a power output of 100 Wh are considered to be in the freight classification of Dangerous Goods and will require special application procedures.
• For transportation abroad, you must comply with international law and the rules and regulations of the destination country.

SAVE THESE INSTRUCTIONS AND MAKE THEM AVAILABLE TO OTHER USERS AND OWNERS OF THIS TOOL!

FUNCTIONAL DESCRIPTION

NOTE
The information contained in this Instruction Manual is designed to assist you in the safe operation and maintenance of the power tool.
NEVER operate, or attempt any maintenance on the tool unless you have first read and understood all safety instructions contained in this manual.
Some illustrations in this Instruction Manual may show details or attachments that differ from those on your own power tool.

NAME OF PARTS

1. Cordless Multi Tool (CV18DA)
2. Battery
3. Battery Charger

SPECIFICATIONS

1. Cordless Multi Tool
   Model| CV18DA
   ---|---
   Motor| Fan-cooled DC brushless motor
   Voltage| 18 V
   No Load Vibration Frequency| 6,000-20,000 /min
   Oscillation angle| 3.6 degrees
   Overall length| 12-7/8″ (327 mm)
   Battery| Model| BSL1820M
   Type| Li-ion battery
   Voltage| DC 18 V
   Weight| 3.5 lbs. (1.6 kg)
2. Battery Charger
   Model| UC18YFSL
   ---|---
   Input power source| Single phase: AC 120 V 60 Hz
   Charging time (At a temperature of 68°F (20°C))| BSL1820M: Approx. 30 min
   Charging voltage| DC 14.4–18 V
   Charging current| DC 3.5 A
   Weight| 1.1 lbs. (0.5 kg)

NOTE
The charging time may vary according to temperature and power source voltage.

ASSEMBLY AND OPERATION

APPLICATIONS

• Flush cutting and pocket cutting of various materials
• Peeling of tiles, caulking, etc.
• Polishing wood materials, etc.

REMOVAL AND INSTALLATION METHOD OF BATTERY

1. Battery removal
   Hold the handle tightly and push the battery latch to remove the battery (see Fig. 6).
   CAUTION
   Never short-circuit the battery.

2. Battery installation
   Insert the battery while observing its polarities (see Fig. 6).

CHARGING METHOD
NOTE
Before plugging into the receptacle, make sure the following points.

• The power source voltage is stated on the nameplate.
• The cord is not damaged.

WARNING
Do not charge at voltage higher than indicated on the nameplate.
If charged at voltage higher than indicated on the nameplate, the charger will burn out.