greenworks G24LT30M Cordless Strimmer Lawn Edger User Manual

greenworks G24LT30M Cordless Strimmer Lawn Edger

Product Information

• Specifications
  • Model: G24LT30M / 21227
  • Manufacturer: GLOBGRO AB
  • Authorized Representative: Garden Equipment Ltd
  • Address: First Floor, 3a Groveley Road, Christchurch, Dorset, BH23 3HB, UK
  • Sound Power Level: Measured – 93.3 dB(A), Guaranteed – 96 dB(A)

Product Usage Instructions

• Safety Precautions
  • Before using the electric string trimmer, please read and understand the following safety precautions:
  • Always wear appropriate protective gear, including safety goggles, gloves, and ear protection.
  • Ensure that the trimmer is used in a well-ventilated area.
  • Keep bystanders, especially children and pets, at a safe distance from the working area.
  • Never operate the trimmer if you are fatigued or under the influence of drugs or alcohol.
  • Inspect the trimmer for any damage or defects before each use. Do not use if any issues are found.
• Assembly
  • To assemble the electric string trimmer, follow these steps:
  • Attach the handle to the main body of the trimmer using the provided screws and a screwdriver.
  • Connect the power cord to the designated socket on the trimmer.
  • Ensure all connections are secure before proceeding.
• Operation
  • To operate the electric string trimmer, follow these steps:
  • Plug the power cord into a suitable power outlet.
  • Hold the trimmer firmly with both hands, ensuring a comfortable grip.
  • Press the power switch to turn on the trimmer.
  • Move the trimmer back and forth in a sweeping motion to trim the desired area.
  • Release the power switch to turn off the trimmer.
• Maintenance
  • To ensure proper functioning and longevity of the electric string trimmer, perform regular maintenance tasks:
  • Clean the trimmer after each use to remove any debris or grass clippings.
  • Inspect the cutting line regularly and replace it if worn or damaged.
  • Check for loose screws or parts and tighten them if necessary.
  • Store the trimmer in a clean and dry place when not in use.
• Frequently Asked Questions (FAQ)
  • Q: Can I use the electric string trimmer in wet conditions?
  • A: No, it is not recommended to use the trimmer in wet conditions as it may pose a safety risk and damage the electrical components.
  • Q: How long is the power cord?
  • A: The length of the power cord is [insert length] meters.
  • Q: Can I use the trimmer for edging?
  • A: Yes, the electric string trimmer can be used for edging by holding it vertically and carefully guiding it along the edges of the desired area.
  • Q: How often should I replace the cutting line?
  • A: The cutting line should be replaced when it becomes worn or damaged. It is recommended to check it regularly and replace it as needed.

DECLARATION OF CONFORMITY

DECLARATION OF CONFORMITY (UK)

Name and address of the manufacturer:

• Name: GLOBGRO AB

Globe Group Europe

• Address: Riggaregatan 53, 211 13 Malmö Sweden

Name and address of the Authorized representative:

• Name: Garden Equipment Ltd

• Address: First Floor, 3a Groveley Road, Christchurch, Dorset, BH23 3HB, UK

• Name and address of the person authorised to compile the technical file:
  
  Name: Simon Del-Nevo

• Address: First Floor, 3a Groveley Road, Christchurch, Dorset, BH23 3HB, UK

Here we declare that the product

• Category: Electric String Trimmer
• Model: 21227
• Serial number: See product rating label
• Year of Construction: See product rating label
  • is in conformity with the relevant provisions of the Supply of Machinery (Safety) Regulations 2008.
  • conforms with the provisions of the following other UK legislation:
• Electromagnetic Compatibility Regulations 2016
• Noise Emission in the Environment by Equipment for Use Outdoors Regulations 2001
• The Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012

Furthermore, we declare that the following standards have been used:

• BS EN 60335-1, BS EN 50636-2-91, BS EN 62233, BS EN 55014-1, BS EN 55014-2,
• BS EN ISO 3744, ISO 11094, BS EN 62321-3-1, BS EN 62321-4, BS EN 62321-5,
• BS EN 62321-6, BS EN 62321-7-1, BS EN 62321-7-2, BS EN 62321-8
• Conformity assessment method to Annex E Noise Emission in the Environment by Equipment for Use Outdoors Regulations 2001.

String Trimmer:

• Measured sound power level 93.3 dB(A)
• Guaranteed sound power level 96 dB(A)
• Place, date: Christchurch, Dorset, UK 07.06.2021
• Signature: Ted Qu, Quality Director

DESCRIPTION

PURPOSE

• You cannot use the machine to cut or chop hedges, shrubs, bushes, flowers and compost.

OVERVIEW

Figure 1 – 16.

1. Trigger
2. Rear handle
3. Lock-out button
4. Auxiliary handle
5. Upper shaft
6. Coupler
7. Lower shaft
8. Guard
9. Edge guide
10. Cut-off blade
11. Trimmer head
12. Edge wheel
13. Pivoting button
14. Edger button
15. Battery release button
16. Spool cover
17. Spool
18. Spool housing
19. Guide slot
20. Hole
21. Spool retainer button
22. Direction of roatation
23. Best cutting area
24. Dangerous cutting area

PACKING LIST

1. String trimmer bare tool
2. Guard assembly
3. Operator manual

SAFETY

WARNING

• Make sure that you follow all safety instructions. Refer to the Safety Manual.

INSTALLATION

WARNING

• Remove the battery pack from the machine before installation.

WARNING

• Do not use accessories that are not recommended for this machine.

UNPACK THE MACHINE

WARNING

• Make sure that you correctly assemble the machine before use.

WARNING

• If parts of the machine are damaged, do not use the machine.
• If you do not have all the parts, do not operate the machine.
• If parts are damaged or missing, contact the service centre.

1. Open the package.
2. Read the documentation provided in the box.
3. Remove all the unassembled parts from the box.
4. Remove the machine from the box.
5. Discard the box and packing material in compliance with local regulations.

ASSEMBLE THE SHAFT Figure 3

1. Insert the lower shaft into the coupler on the upper shaft.
   • NOTE: Make sure the upper and lower parts of the shafts are securely tightened before installing the battery pack again.
2. Tighten the coupler.

INSTALL THE BATTERY PACK Figure 4.
WARNING

• If the battery pack or charger is damaged, replace the battery pack or the charger.
• Stop the machine and wait until the motor stops before you install or remove the battery pack.
• Read, know, and follow the instructions in the battery and charger manual.

1. Align the lift ribs on the battery pack with the grooves in the battery compartment.
2. Push the battery pack into the battery compartment until the battery pack locks into place.
3. When you hear a click, the battery pack is installed.

REMOVE THE BATTERY PACK Figure 4.

1. Push and hold the battery release button.
2. Remove the battery pack from the machine.

OPERATION

• IMPORTANT
  • Before you operate the machine, read and understand the safety regulations and the operation instructions.
• WARNING
  • Be careful when you operate the machine.

START THE MACHINE Figure 5.

1. Pull back on the lock-out button and pull the trigger.

STOP THE MACHINE Figure 5.

1. Release the trigger to stop the machine.

OPERATION TIPS Figure 6.

WARNING

• Keep clearance between the body and the machine.

WARNING

• Do not operate the machine without a guard in place.
• Do these tips when you use the machine
• Keep the machine connected to the correctly worn harness.
• Keep a firm hold with the two hands on the machine while you operate the machine.
• Cut tall grass from the top down. If grass winds around the trimmer head:
• Remove the battery pack.
• Remove the grass.

CUTTING TIPS Figure 7.

• Tilt the machine toward the area to be cut. Use the tip of the cutting line to cut grass.
• Move the machine from right to left to prevent debris toward the operator.
• Do not cut in dangerous areas.
• Do not force the trimmer head into uncut grass.
• Wire and picket fences cause cutting line wear and breakage. Stone and brick walls, curbs, and wood can wear the cutting line quickly.

ADJUST THE LENGTH OF THE CUTTING LINE MANUALLY Figure 8

1. Stop the machine.
2. Pastate pole in bute and pul on cutting line to
3. Machiyou is normal use liberal you sum again.

LINE CUT-OFF BLADE Figure 9.

• Whenever you let heroine minis as ha mama est performance and keep line long enough to advance properly.

ADJUST THE LENGTH OF THE CUTTING LINE Figure 5.

NOTE

• The machine has an auto-feed head. It will damage the machine if you hit the head to try to advance the line.

NOTE

• If the cutting line does not automatically advance, it can be tangled or empty.

1. When the machine is on, release the trigger.
2. Wait two seconds, and push the trigger again.

NOTE

• The line will extend approximately 0.4 in. with each stop and start of the switch trigger until the line reaches the cut- off blade and the cut-off blade cuts the excess length.

Figure 9. ADJUST THE CUTTING DIAMETER
NOTE
The machine is set at a 254 mm cutting diameter. You can adjust to a 305 mm cutting diameter. Set the cutting diameter to 254 mm for greater runtime and 305 for a larger cutting area.

1. Remove the battery pack.
2. Remove the blade screws from the cut-off blade.
3. Turn the cut-off blade 180°.
4. Tighten the blade screws.

CHANGE TO THE EDGING MODE Figure 6.
NOTE
You can change the machine to a well-groomed edger for edging patios, driveways walkways or other areas.

1. Stop the machine.
2. Push on the edge button and turn the trimmer head 90 degrees until the trimmer head locks into position.
3. Release the edge button.

PIVOTING HEAD FUNCTION Figure 10.
NOTE: Adjust the pivoting head to trim areas that are hard to reach and for users to operate comfortably.

1. Stop the machine.
2. Push on the pivoting button and turn the shaft until the trimmer head locks into the required position.
3. Release the pivoting button.

MAINTENANCE

• IMPORTANT
  • Read and understand the safety regulations and the maintenance instructions before you clean, repair or do the maintenance work on the machine.
• IMPORTANT
  • Make sure that all nuts, bolts and screws are tight. Examine regularly that you install the handles tightly.
• IMPORTANT
  • Use only the replacement parts and accessories of the initial manufacturer.

GENERAL INFORMATION

• IMPORTANT
  • Only your dealer or approved service centre can do the maintenance that is not given in this manual.

Before the maintenance operations:

• Stop the machine.
• Remove the battery pack.
• Cool the motor.
• Store the machine in a cool and dry place.
• Use correct clothing, protective gloves and safety glasses.

CLEAN THE MACHINE

• Clean the machine after use with a moist cloth dipped in neutral detergent.
• Do not use aggressive detergents or solvents to clean the plastic parts or handles.
• Keep the trimmer head free of grass, leaves, or excessive grease.
• Keep the air vents clean and free of debris to avoid overheating and damage to the motor or the battery.
• Do not spray water onto the motor and electrical components.

REPLACE THE SPOOL Figure 11.

1. Push the tabs on the sides of the trimmer head at the same time.
2. Pull and remove the spool cover.
3. Remove the spool.
4. Replace with a new spool.
   • NOTE: Make sure that the cutting line is in the guide slot on the new spool, and is extended approximately 5 in. before you install the new spool.
5. Put the end of the cutting line through the eyelet.
6. Extend the cutting line to release it from the guide slot in the spool.
7. Push the tabs and install the spool cover onto the spool housing.
8. Push the spool cover until it clicks into position.

REPLACE THE CUTTING LINE Figure 12 – 16.
NOTE

• Remove the remaining cutting line on the spool.

NOTE

• Use only with the nylon cutting line of 1.65 mm diameter.

1. Cut a piece of cutting line approximately 3m long.
2. Bend one end of the line 1/4 of an inch (6.35mm).
3. Insert the line into the anchor hole of the spool.
4. Wind the cutting line around the spool tightly in the indicated direction.
5. Put the cutting line in the guide slot.
6. Do not wind the cutting line beyond the edge of the spool.

TRANSPORTATION AND STORAGE

MOVE THE MACHINE
When you move the machine, you must:

• Wear gloves.
• Stop the machine.
• Remove the battery pack and charge it.
• Assemble the blade guard.

STORE THE MACHINE

• Remove the battery pack from the machine.
• Make sure that children cannot come near the machine.
• Keep the machine away from corrosive agents such as garden chemicals and de-icing salts.
• Secure the machine during transportation to prevent damage or injury. Clean and examine the machine for any damage.

TROUBLESHOOTING

2. Check contact and in- install the battery pack again.

The battery pack is depleted.| Charge the battery pack.
The lock-out button and trigger are not pushed at the same time.| 1. Pull the lock-out button and hold it.

2. Pull the trigger to start the machine.

The machine stops when you cut.| The guard is not attached to the machine.| Remove the battery pack and attach the guard to the machine.
A heavy cutting line is used.| Use only with the nylon cutting line of 1.65 mm diameter.
 | The grass winds around the motor shaft or the trimmer head.| 1. Stop the machine.

2. Remove the battery pack.

 |  | 3. Remove the grass from the motor shaft and trimmer head.
 | The motor is over-loaded.| 1. Remove the trimmer head from the grass.
 |  | 2. The motor will recover to work as soon as the load is removed.
 |  | 3. When you cut, move the trimmer head in and out of the grass to be cut and remove no more than 8″ in pass.
 | The battery pack or machine is too hot.| 1. Cool the battery pack until its function returns to normal.
 |  | 2. Cool the machine for approximately 1O minute.
 | The battery pack is disconnected from the tool.| Install the battery pack again.
 | The battery pack is depleted.| Charge the battery pack.
Problem| Possible Cause| Solution
---|---|---
The line does not ad- vance.| Lines are welded to themselves.| Lubricate with silicone spray.
Not enough line on spool.| Install more line.
Lines are worn too short.| Advance the cutting line.
Lines are tangled on spool.| 1. Remove the lines from the spool.

2. Wind the lines.

The line keeps breaking.| The machine is used incorrectly.| 1. Cut with the tip of the line, avoid stones, walls and other hard objects.

2. Advance the cutting line regularly to keep full cutting width.

The grass winds around the trimmer head and motor hous- ing.| Cut tall grass at ground level.| 1. Cut tall grass from the top down.

2. Remove no more than 8″ in each pass to prevent wrapping.

The line does not cut well.| The cut-off blade becomes dull.| Sharpen the cut- off blade with a file or replace it.
Vibration increases obviously.| The line is worn down at one side and not advanced in time.| Make sure that the line on both sides is normal. Ad- vance the line.

TECHNICAL DATA

• Charger model: G24C and other CAG series
• Noise value.

WARRANTY

• (The full warranty terms and conditions can be found on the Greenworks website www.greenworkstools.eu.)
• The Greenworks warranty is for 3 years on the product and 2 years on batteries (consumer/private usage) from the date of purchase.
• This warranty covers manufacturing faults. A faulty product under warranty might be either repaired or replaced. A unit that has been misused or used in other ways than described in the owner’s manual might be rejected for warranty.
• Normal wear and wear parts are not considered a warranty.
• The original manufacturer warranty is not affected by any additional warranty offered by a dealer or retailer.
• A faulty product must be returned to the point of purchase in order to claim for warranty, together with the proof of purchase (receipt).

EC DECLARATION OF CONFORMITY

Name and address of the manufacturer:

• Name:
  • GLOBGRO AB
  • Globe Group Europe
• Address:
  • Riggaregatan 53, 211 13 Malmö, Sweden

Name and address of the person authorised to compile the technical file:

• Name:
  • Micael Johansson
• Address:
  • Riggaregatan 53, 211 13 Malmö, Sweden

Herewith we declare that the product

• Category: Grass trimmer
• Model: 21227
• Serial number: See product rating label
• Year of Construction: See product rating label
  • is in conformity with the relevant provisions of the Machinery Directive 2006/42/EC. conforms with the provisions of the following other EC-Directives:
  • 2014/30/EU
  • 2000/14/EC & 2005/88/EC
  • 2011/65/EU & (EU)2015/863
  • Furthermore, we declare that the following (parts/clauses of) harmonised standards have been used:
  • EN 60335-1; EN 50636-2-91; EN 62233; EN 55014-1;
  • EN 55014-2:2015; EN ISO 3744; EN ISO 3744; ISO
  • 11094; IEC 62321-7-2; IEC 62321-4; IEC 62321-5; IEC
  • 62321-6; IEC 62321-7-1; IEC 62321-8; IEC 62321-3-1
  • Conformity assessment method to Annex VI / Directive 2000/14/EC.

Grass trimmer

• Measured sound power level: LwA=93.3 dB(A)
• Guaranteed sound power level: LwA.d=96 dB(A)
• Place, date Signature: Ted Qu, Quality Director

References

• Powerful Cordless Gardening Tools | Greenworks Tools

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>