Rollerhouse DC2700 Motorized Screen Remote Instructions

June 15, 2024
Rollerhouse

Rollerhouse Logo Rollerhouse DC2700 Motorized Screen
RemoteMotorized Screen
Remote Instructions
DC2700 Remote – Single Channel

IMPORTANT READ ME FIRST

  1. The delay time between buttons is within 6 seconds. If there is no input within 6 seconds, the remote will exit the current setting procedure
  2. The motor will jog and beep as a hint. Continue programming after the hint.

Pairing

Apply power to motor (1 jog andlong beep once), within 7s, press STOP for 2s (2 jogs and 3 beeps), the motor has been paired successfully

Switching Rotating Direction (Optional)

If the UP button is pressed, but the screen goes down, you will need to complete this step
Press and hold the UP and DOWN buttons simultaneously for 2s, motor will jog once and rotation will be switched successfully
*The motor needs to be in the reversing operation without limits

Setting Upper and Lower Limits

UPPER LIMIT
Move the screen up to the desired upper limit
Press and hold UP + STOP simultaneously for 2s (2 jogs, 3 beeps) upper limit

LOWER LIMIT
Move the screen down to the desired lower limit
Press and hold DOWN + STOP simultaneously for 2s (2 jogs, 3 beeps) Lower limit is set

Adjusting Limits

Adjust Upper Limit

Press and hold UP + STOP simultaneously for 5s (1 jog, 1 Long beep) Repeat step 3

Adjusting Lower Limit
Press and hold DOWN + STOP simultaneously for 5s (1 jog, 1 Long beep) Repeat step 3

Preferred Position

Set Preferred Position

Rollerhouse DC2700 Motorized Screen Remote - Position

Check that both upper and lower limits are set.
Operate the screen to the desired preferred position. Press P2 (1 jog and 1 beep), press STOP (1 jog and 1 beep), press STOP again (2 jogs and 3 beeps), preferred position is now set
Remove Preferred

Rollerhouse DC2700 Motorized Screen Remote - Remove
Preferred

Press P2 (1 jog and 1 beep), press STOP (1 jog and 1 beep), press STOP again (1 jog and 1 Long beep), preferred position is now deleted

Delete All Limits

Rollerhouse DC2700 Motorized Screen Remote - All
Limits

Press P2 (1 jog and 1 beep), Down and 1 beep), P2 (2 jogs and 3 beeps), all limits are now removed

Pair / Unpair Additional Remotes

Rollerhouse DC2700 Motorized Screen Remote - Unpair
Additional

On existing remote, Press P2 (1 jog and 1 beep) Press P2 again (1 jog and 1 beep), then on new remote, press P2 (2 jogs and 3 beeps). New remote is now linked. Repeat for any additional remotes

Remove All Remotes

Rollerhouse DC2700 Motorized Screen Remote - RemotesPress P2 (1 jog and 1 beep), STOP (1 jog and one beep), P2 (2 jogs and 3 beeps)

Motor Mode Switching

Rollerhouse DC2700 Motorized Screen Remote - SwitchingPress P2 (1 jog and 1 beep), UP (1 jog and one beep), UP (1 jog and 1 long beep)

Troubleshooting

Issue — Possible Cause Solution
Motor has no response – No Power or poor wire connection Check power and

connections
Motor has no response – Remote battery low| Replace Battery
Motor has no response – RF Interference| Check motor antenna, check for other RF source interference
Motor has no response – Out of remote control range| Move remote closer to unit

Rollerhouse Logo

Read User Manual Online (PDF format)

Loading......

Download This Manual (PDF format)

Download this manual  >>

Rollerhouse User Manuals

Related Manuals