Sweetcrispy C-2639 Padded Armrests Executive Office Chair Instruction Manual
- June 15, 2024
- Sweetcrispy
Table of Contents
Sweetcrispy C-2639 Padded Armrests Executive Office Chair
ASSEMBLY GUIDE
Congratulations, you are now the owner of a brand new ergonomic chair!
To best enjoy the comfort of the chair, you have to put it together first!
This assembly guide will take you through the assembly process. To make sure
the assembly goes well, please follow the instructions, and especially the
important safety information. It is possible to assemble the chair on your
own, but it is recommended to have a second person to make it easier and
safer.
Please check if there are any missing parts from the package before starting. If there is any issue, please don’t hesitate to drop us an email and we’ll help you out ASAP. If you run into any difficulty when assembling the chair, remember to check out the assembly video to see if you’ve missed anything. If you’re unable to resolve the problem, just send us an email and our support team will assist you.
https://qygjuser.s3.us-east-2.amazonaws.com/HL/HLC-2639L.mp4
WARNING
To ensure proper assembly, please follow all steps and use all parts. Failure
to follow this warning can result in serious injury to yourself or others.
Package List
Without further ado, we kindly suggest you to list all parts needed for the chair first.
-
*1
Backrest -
*1
Seat Cushion
-
1(L)1(R)
Armrests
-
*1
Mechanism
-
*1
Gas Lift
-
*1
Base
-
*5
Casters -
*4
Bolts -
*8
Bolts -
*8
Protective Lid -
*1
Telescope Cover
-
*1
Wrench
Assembly Instruction
Step 1:
Turn the Base (6) upside down, press the Casters (7) into the holes at the end of each Leg
Step 2:
Then insert the Gas Lift (5) into the center hole of the Base. The Telescope Cover (11) should be placed over the Gas Lift.
Step 3:
Align the Mechanism (4) over the pre-drilled holes underneath the Seat Cushion (2). Then fix it with the Bolts (8) and Wrench (12).
Note:
Make sure the front of the mechanism and the knob is facing the front of
the seat. There is a marking of FRONT on the mechanism and the seat.
Step 4:
Position the assembled chair upright with the Seat Mechanism (4) facing down. lnsert the Gas Lift (5) into the center hole of the Seat Mechanism (4) and press down until fully engaged.
Step 5:
Fix the right and left Armrests (3) with the Bolts (9).
All bolts do not need to be tightened, they only need to be fixed in half
Note: Armrests are labeled with an “L” (left) or “R” (right) to show which sides they should be placed on.
Step 6:
Attach the Backrest (1) to the Armrest (3). Use the Wrench (12) to screw Bolts (9) on the left and right. The installation of the other side is the same.
All bolts do not need to be tightened, they only need to be fixed in half
Step 7:
Rotate the back of the chair up, then secure it with the Bolt (9) and use the Wrench (12). Adjust the balance on each side of the chair, and 100% tighten all the bolts at this step. The installation of the other side is the same.
Step 8:
Press Protective Lid (10) into the screw holes on each side.
CAUTION:
Make sure all bolts and screws are fully tightened before using chair.
Lubricate all moving parts and tighten all bolts/screws every 6 months or
whenever needed.
Instructions For Use
- Seat Height: Paddle-shaped lever on the right side
- At the proper height, your feet should rest flat on the floor.
2. Tilt Tension: Long stem under the seat with knob
- Set the tilt tension to control the resistance you feel when leaning back.
3. Operating the tilt lockout
To let your chair tilt back, pull the control handle out. To stop your chair from tilting, sit forward, then push the control handle in.
Safety And Maintenance
- Do not stand on the chair, Do not use the chair as a stepladder.
- Use this product for seating one person at a time.
- Do not use the chair unless all bolts and screws are firmly secured.
- Avoid contact with sharp objects to prevent puncturing the fabric.
- Every 6 months, check all bolts and screws to ensure they are tight.
- To clean, spot clean only using a damp towel and mild cleaner, first test on a small, unseen area of fabric.
- Chair weight limit not to exceed 250 lbs.
Safety Information
-
Sit in the center of the chair, with your back to the backrest
-
Do not sit at the front edge of the chair
-
Do not stand on the chair
-
Do not use the chair with more than one person
-
Do not push the chair around when a person is sitting in it
-
Do not push down on the backrest when a person is reclined
-
Do not place all your weight on only the backrest
Limited Warranty
The producer promises to repair or replace any chair that is found to be defective in material or workmanship within one (1) year from the date of original purchase so long as you, the original purchaser, still owns it. This is your sole and exclusive remedy. This warranty is subject to the provisions below.
EXCLUSIONS:
This warranty does not apply and no other warranty applies to:
- Normal wear and tear, which are to be expected over the course of ownership.
- Misuse, abuse, or excessive use of the product.
- Modifications or attachments to the product that are not approved by the manufacturer.
- Products that were not installed, used or maintained in accordance with product instructions and warnings.
- Products used for rental or commercial purposes.
- Damage caused by the carrier in-transit is handled under separate terms.
SEATING USAGE:
Normal use for seating is identified as the equivalent of a single shift,
forty- (40) hour workweek. To the extent that a seating product is used in a
manner exceeding this, the applicable warranty period will be reduced in a
pro-rata manner.
Some retailers might have custom models imported directly from the factory and
therefore are not supported by our local service team because we don’t have
the correct parts, please contact your retailer directly for support. If you
have any questions about that we will be happy to assist and identify those
items.
RETURN POLICY:
We adopt a 30 days return policy which means that all products purchased on
this website may be returned to us within the timeframe. You need to contact
us within 30 days after the product(s) came into your possession and the
product(s) must be returned to us without any undue delays. Returned products
must be returned in the same condition as they were sent and they must be sent
in its original packaging.
If the product is not faulty, (i.e. if you changed your mind or if you are
unhappy with the product for some other reason), the cost of shipping will all
on you. And it is your responsibility that the package arrives safely to us so
we recommend that you use a courier service where it is possible to track the
shipment.
If the product is faulty when you receive it please contact us and we will
help you out (see more information under Manufacturer Warranty). We reserve
the right to give a partial refund in cases when the product(s) is not in an
unused condition, is damaged or has missing parts not due to our error.
HOW RETURNS WORK:
Contact us through the contact form on our website and attach the invoice to
the message as proof of purchase. And please also write the reason for the
return.
We will then get back to you as soon as possible with information on where to
send the product(s).
As soon as we have received the product(s) and made an inspection we will
inform you of our decision.
If a refund is approved we will automatically credit the purchase to your
credit card or original method of payment.
If the product(s) is damaged, not in its original condition or missing parts
we will inform you if you are eligible for a partial refund. This is decided
from case to case depending on the severity of the damages or what parts are
missing.
Customers Support
[email protected]
(909)637-7665 | (909)637-7593
EST 9:00AM–17:00PM
Documents / Resources
|
Sweetcrispy C-2639 Padded Armrests Executive Office
Chair
[pdf] Instruction Manual
C-2639 Padded Armrests Executive Office Chair, C-2639, Padded Armrests
Executive Office Chair, Armrests Executive Office Chair, Executive Office
Chair, Office Chair, Chair
---|---