Sweetcrispy C-2892-1B Home Office Chair Instruction Manual
- June 14, 2024
- Sweetcrispy
Table of Contents
INSTRUCTION MANUAL
C-2892-1B Home Office Chair
Model: C-2892-1B
HJ-Customer-Service@outlook.com
(909)637-7665 | (909)637-7593
EST 9:00AM–17:00PM
ASSEMBLY GUIDE
Congratulations, you are now the owner of the new chair!
Before enjoying the comfortable chair, you have to assemble it. This assembly
guide will take you through the basic assembly process. To make sure your
assembly progress goes smoothly, please follow the assembly instructions
especially the important safety information.
It is possible to assemble the chair by your own, while having a second person
to help you will make it easier.
Please check if there are any missing parts in the package before start. If
there are any issues, please don’t hesitate to drop us an email and we’ll help
you ASAP.
If you run into any difficulty during the assembly, remember to check out the
assembly Video to see if you’ve missed something. If you’re still unable to
resolve your problems , drop us an email and our support team will assist you.
https://hlinstallationvideos.s3.amazonaws.com/2892+-+leather+chair.mp4
WARNING
To ensure proper assembly, please follow all steps and use all parts. Failure
to follow this warning can result in serious injury to yourself or others.
Package List
- Without further ado, we kindly suggest you to list all parts needed for the chair first.
Assembly Instruction
Step 1:
Turn the Base (7) upside down, then insert Legs (6) one by one to
Base.
Use the Wrench (13) to screw
Ten Bolts (11) into the pre-drilled screw holes to fix Base and Legs.
Step 2:
Both hands are forced at the same time to press the Casters (8) into the holes
at the end of each Base Leg.
- Step 3: Insert the Gas Lift (5) into the center hole of the Base.
Step 4 : Align the Mechanism (4) over the pre-drilled holes
underneath the Seat (2).
Attach the Mechanism to the Seat using Four Bolts (9), tighten all the
bolts with the Wrench (13).
( Note! Don’t make the direction wrong, make sure the front of the
Mechanism (4) is facing the front of the Seat. )
Step 5 :
Turn the Seat (2) upright and align the center hole of the Seat Plate over
the lift, then push the Seat down onto the lift firmly until the connection is
secure.
Attach the Armrest (3) to the Seat ( 2 ) with Two Bolts (10), using
the Wrench (13)to tighten.
The Bolt only needs to be screwed in 50%. The installation of the other side
Armrest is the same.
Note 1: The same marks on both seat and armrests are tips for installing
the armrests in the correct direction.
Note 2: Armrests are labeled with letter “L” (left) or “R” (right).
Step 6 :
Set the Back (1) stand up.
Attach the Back (1) to the Arms by inserting one Bolt (10) in the
holes with the Wrench (13). The Bolt only needs to be screwed in 50%.
Step 7 :
Rotate the back of the chair up, then secure it with the Bolt (10) use the
Wrench (13). Adjust the balance on each side of the chair, and 100%
tighten all the bolts at this step.
Step 8 :
Press Caps (12) into screw holes of each side.
CAUTION: Make sure all bolts and screws are fully tightened before
using chair.
Lubricate all moving parts and tighten all bolts/screws every 6 month or
whenever needed.
Instructions For Use
-
Seat Height: Paddle-shaped lever on the right side
* At the proper height, your feet should rest flat on the floor. -
Tilt Tension: Long stem under the seat with knob
* Set the tilt tension to control the resistance you feel when leaning back. -
Operating the tilt lockout
To let your chair tilt back, pull the control handle out.
To stop your chair from tilting, sit forward, then push the control handle in. -
Armrests adjustment The armrest can be adjusted.
Make it up and down if you need .
Safety And Maintenance
- Do not stand on the chair, Do Not use the chair as a stepladder.
- Use this product for seating one person at a time.
- Do not use the chair unless all bolts and screws are firmly secured.
- Avoid contact with sharp objects to prevent puncturing the fabric.
- Every 6 months, check all bolts and screws to ensure they are tight.
- To clean, spot clean only using a damp towel and mild cleaner, first test on a small, unseen area of fabric.
- Chair weight limit not to exceed 275 lbs.
Safety Information
Limited Warranty
The producer promises to repair or replace any chair that is found to be
defective in material or workmanship within one(1) and year from the date of
original purchase so long as you, the original purchaser, still owns it. This
is your sole and exclusive remedy. This warranty is subject to the provisions
below.
EXCLUSIONS:
This warranty does not apply and no other warranty applies to:
Normal wear and tear, which are to be expected over the course of ownership.
Misuse, abuse, or excessive use of the product.
Modifications or attachments to the product that are not approved by the
manufacturer.
Products that were not installed, used or maintained in accordance with
product instructions and warnings.
Products used for rental or commercial purposes.
Damage caused by the carrier in-transit is handled under separate terms.
SEATING USAGE:
Normal use for seating is identified as the equivalent of a single shift,
forty- (40) hour workweek. To the extent that a seating product is used in a
manner exceeding this, the applicable warranty period will be reduced in a
pro-rata manner.
Some retailers might have custom models imported directly from the factory and
therefore are not supported by our local service team because we don’t have
the correct parts, please contact your retailer directly for support. If you
have any questions about that we will be happy to assist and identify those
items.
RETURN POLICY ：
We adopt a 30 days return policy which means that all products purchased on
this website may be returned to us within the timeframe. You need to contact
us within 30 days after the product(s) came into your possession and the
product(s) must be returned to us without any undue delays. Returned products
must be returned in the same condition as they were sent and they must be sent
in its original packaging.
If the product is not faulty, (i.e. if you changed your mind or if you are
unhappy with the product for some other reason), the cost of shipping will all
on you. And it is your responsibility that the package arrives safely
to us so we recommend that you use a courier service where it is possible to
track the shipment.
If the product is faulty when you receive it please contact us and we will
help you out (see more information under Manufacturer Warranty).
We reserve the right to give a partial refund in cases when the product(s) is
not in an unused condition, is damaged or has missing parts not due to our
error.
HOW RETURNS WORK：
Contact us through the contact form on our website and attach the invoice to
the message as proof of purchase. And please also write the reason for return.
We will then get back to you as soon as possible with information on where to
send the product(s).
As soon as we have received the product(s) and made an inspection we will
inform you of our decision.
If a refund is approved we will automatically credit the purchase to your
credit card or original method of payment.
If the product(s) is damaged, not in its original condition or missing parts
we will inform you if you are eligible for a partial refund. This is decided
from case to case depending on the severity of the damages or what parts are
missing.
HJ-Customer-Service@outlook.com
(909)637-7665 | (909)637-7593
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>