VIVO STAND-V155M Articulating Arm Single TV Desk Mount Instruction Manual
- June 15, 2024
- Vivo
Table of Contents
VIVO STAND-V155M Articulating Arm Single TV Desk Mount
Product Information
- Product Name: Articulating Arm Single TV Desk Mount
- SKU: STAND-V155M
- Manufacturer: VIVO
- Website: https://vivo-us.com/products/stand-v155m
Specifications
- Weight Capacity: 44lbs (20kg)
- Color: Black
- Material: Steel
- Compatibility: VESA patterns up to 100x100mm and 75x75mm
Product Usage Instructions
Package Contents
- A (x1) Base
- B (x1) Top Pole
- C (x1) Bottom Pole
- D (x1) Arm
- E (x1) Support Plate
- F (x1) Grommet Plate
- G (x1) Pad
- H (x1) Cover
- I (x1) Clamp Brace
- J (x1) Lower Clamp
- K (x2) VESA Adapter Set
- L (x1) Arm Clamp
- M (x1) Arm Cable Clip
- N (x1) Pole Cable Clip
- S-A (x2) M10x63mm Screw
- S-B (x4) M6x12mm Screw
- S-C (x2) M8x55mm Screw
- S-D (x8) M6x8mm Screw
- S-E (x2) M8 Nut
- T-A (x1) 4mm Allen Wrench
- T-B (x1) 6mm Allen Wrench
- T-C (x1) Wrench
- M-A (x4) M6x14mm Screw
- M-B (x4) M8x16mm Screw
- M-C (x4) M6x30mm Screw
- M-D (x4) M8x35mm Screw
- M-E (x4) M8 Washer
- M-F (x4) Small Spacer
- M-G (x4) Large Spacer
Tools Needed
- Phillips Screwdriver
Assembly Steps
Step 1 (Option A) – Clamp Installation:
Assemble Clamp Brace (I) to Base (A) using M6x12mm Screws (S-B) and 4mm Allen Wrench (T-A). Remove adhesive backing from Pad (G) and place it on the underside of the clamp assembly.
- Components: A, I, G
- Hardware: S-B, T-A
Instructions:
- Attach Clamp Brace (I) to Base (A) using two M6x12mm Screws (S-B) and tighten them with a 4mm Allen Wrench (T-A).
- Remove the adhesive backing from Pad (G) and stick it on the underside of the clamp assembly.
Step 2 (Option A) – Clamp Installation:
Insert M10x63mm Screws (S-A) into Lower Clamp (J) using 6mm Allen Wrench (T-B). Loosen the screws on the back of Lower Clamp (J) so that 6mm of threads are exposed using 4mm Allen Wrench (T-A). Assemble Lower Clamp (J) to Clamp Brace (I) in one of two positions as shown below, depending on the thickness of the desktop. Tighten screws using 4mm Allen Wrench (T-A).
- Components: J, I
- Hardware: S-A, T-A, T-B
Instructions:
- Insert two M10x63mm Screws (S-A) into the holes on Lower Clamp (J) using a 6mm Allen Wrench (T-B).
- Loosen the screws on the back of Lower Clamp (J) using a 4mm Allen Wrench (T-A) until 6mm of threads are exposed.
- Attach Lower Clamp (J) to Clamp Brace (I) in one of two positions based on the thickness of the desktop.
- Tighten the screws using a 4mm Allen Wrench (T-A).
Step 2 (Option A Continued) – Clamp Installation:
Secure the clamp assembly to the desktop by tightening M10x63mm Screws (S-A) using 6mm Allen Wrench (T-B). Place Cover (H) over the back of Clamp Brace (I).
Components: H, I
Hardware: S-A, T-B
Instructions:
- Tighten the M10x63mm Screws (S-A) using a 6mm Allen Wrench (T-B) to securely attach the clamp assembly to the desktop.
- Place Cover (H) over the back of Clamp Brace (I) for a finished look.
Step 1 (Option B) – Grommet Installation:
Assemble Grommet Plate (F) to Base (A) using M6x12mm Screws (S-B) and 4mm Allen Wrench (T-A). Remove adhesive backing from Pad (G) and place it on the underside of the assembly.
Components: A, F, G
Hardware: S-B, T-A
Instructions:
-
Attach Grommet Plate (F) to Base (A) using two M6x12mm Screws
(S-B) and tighten them with a 4mm Allen Wrench (T-A). -
Remove the adhesive backing from Pad (G) and stick it on the
underside of the assembly.
Step 2 (Option B) – Grommet Installation:
Install Base (A) to an existing grommet hole in the desktop using Support Plate (E) with M10x63mm Screw (S-A) and 6mm Allen Wrench (T-B).
Components: A, E
Hardware: S-A, T-B
Instructions:
- Place Support Plate (E) on the underside of Base (A).
- Insert one M10x63mm Screw (S-A) through the hole in Support
Plate (E) and screw it into an existing grommet hole in the desktop using a 6mm Allen Wrench (T-B).
Step 3 – Pole Assembly:
Thread Bottom Pole (C) into Top Pole (B). Thread the pole assembly onto Base (A) with Pole Cable Clip (N). Tighten the set screws in the bottom of Base (A) using the flat end of 4mm Allen Wrench (T-A).
Components: B, C, A, N
Hardware: None
Instructions:
- Screw Bottom Pole (C) into Top Pole (B) until they are securely connected.
- Thread the pole assembly onto Base (A) and tighten it.
- Use the flat end of a 4mm Allen Wrench (T-A) to tighten the set screws in the bottom of Base (A).
Step 4 – VESA Plate:
Remove the nuts on the back of the VESA plate on Arm (D) using Wrench (T-C) and remove the plate.
- Components: D
- Hardware: T-C
Instructions:
- Use Wrench (T-C) to remove the nuts on the back of the VESA plate attached to Arm (D).
- Remove the VESA plate from Arm (D).
Step 5 – Arm Assembly:
Assemble Arm (D) to the pole assembly using Arm Clamp (L) with M8x55mm Screws (S-C) and M8 Nuts (S-E). Tighten using 6mm Allen Wrench (T-B). Attach Arm Cable Clip (M) to Arm (D).
- Components: D, L, M
- Hardware: S-C, S-E, T-B
Instructions:
- Attach Arm Clamp
Articulating Arm Single TV Desk Mount
Instruction Manual
SKU: STAND-V155M
Scan the QR code with your mobile device or follow the link for helpful videos
and specifications related to this product.
https://vivo-us.com/products/stand-v155m
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
- NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR STAND.
- USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
PACKAGE CONTENTS
TOOLS NEEDED
NOTE: NOT ALL HARDWARE INCLUDED WILL BE USED
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
ASSEMBLY STEPS
STEP 1 (Option A)
Clamp Installation:
Assemble Clamp Brace (I) to Base (A) using M6x12mm Screws (S-B) and 4mm Allen
Wrench (T-A). Remove adhesive backing from Pad (G) and place it on the
underside of the clamp assembly.
STEP 2 (Option A)
Clamp Installation:
Insert M10x63mm Screws (S-A) into Lower Clamp (J) using 6mm Allen Wrench
(T-B). Loosen the screws on the back of Lower Clamp (J) so that 6mm of threads
are exposed using 4mm Allen Wrench (T-A). Assemble Lower Clamp (J) to Clamp
Brace (I) in one of two position as shown below, depending on the thickness of
the desktop. Tighten screws using 4mm Allen Wrench (T-A).
Secure the clamp assembly to the desktop by tightening M10x63mm Screws (S-A) using 6mm Allen Wrench (T-B). Place Cover (H) over the back of Clamp Brace (I).
STEP 1 (Option B)
Grommet Installation:
Assemble Grommet Plate (F) to Base (A) using M6x12mm Screws (S-B) and 4mm
Allen Wrench (T-A). Remove adhesive backing from Pad (G) and place it on the
underside of the assembly.
Assemble Grommet Plate (F) to Base (A) using M6x12mm Screws (S-B) and 4mm
Allen Wrench (T-A). Remove adhesive backing from Pad (G) and place it on the
underside of the assembly.
STEP 2 (Option B)
Grommet Installation:
Install Base (A) to an existing grommet hole in the desktop using Support
Plate (E) with M10x63mm Screw (S-A) and 6mm Allen Wrench (T-B).
STEP 3
Thread Bottom Pole (C) into Top Pole (B). Thread the pole assembly onto
Base (A) with Pole Cable Clip (N). Tighten the set screws in the bottom of
Base (A) using the flat end of 4mm Allen Wrench (T-A).
STEP 4
Remove the nuts on the back of the VESA plate on Arm (D) use Wrench (T-C)
and remove the plate.
STEP 5
Assemble Arm (D) to the pole assembly using Arm Clamp (L) with M8x55mm Screws
(S-C) and M8 Nuts (S-E). Tighten using 6mm Allen Wrench (T-B). Attach Arm
Cable Clip (M) to Arm (D).
STEP 6
Install VESA Adapter Set (K) to the previously removed VESA Plate using M6x8mm
Screws (S-D) in the appropriate configuration based on your TV’s VESA pattern.
STEP 7
Secure the VESA plate assembly to the back of the TV using Screws (M-A through
M-D) with M8 Washers (M-E). Spacers (M-F, M-G) may be required. Tighten screws
using a Phillips screwdriver.
STEP 8
Secure the VESA plate assembly to Arm (D) using the previously removed nuts
and washers. Tighten the nuts using Wrench (T-C).
STEP 9
Adjust the tilt using 4mm Allen Wrench (T-A).
STEP 10
Route cables through Arm Cable Clip (M) and Pole Cable Clip (N).
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
Open Monday – Friday 7:00am – 7:00pm CST,our dedicated support team can offer immediate assistance with rapid response times. If any parts are received damaged or defective, please contact us. We are happy to replace parts to ensure you have a fully functioning product.
309-278-5303 AVG. RESOLUTION TIME (within office hrs): 5M 4S
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within office hrs): < 15 M
AVG. RESPONSE TIME (within office hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
www.vivo-us.com
Chat live with an agent!
309-278-5303
References
- Register a .US.COM domain today!
- VIVO - Desks, Monitor Mounting, and More Home & Office Solutions – VIVO - desk solutions, screen mounting, and more
- Articulating Arm Single TV Desk Mount – VIVO - desk solutions, screen mounting, and more
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>