ANYSECU JC-8900 Two Way Radio VHF UHF FM Transceiver Instruction Manual

JC-8900 Two Way Radio VHF UHF FM Transceiver
Instruction Manual

Function：

1. Frequency band
   FM 65 – 108 MHZ （Receive）
   VHF 108 – 136 MHz （AM receive）
   VHF 136 – 174 MHZ （RX/TX）
   UHF 220 – 260 MHZ （RX/TX）
   UHF 330 – 390 MHZ （RX/TX）
   UHF 400 – 520 MHZ （RX/TX）

2. Working mode：Frequency mode/Channel mode

3. AM air band

4. FM Radio

5. Dual standby

6. 50 CTCSS/105 DCS

7. RX CTCSS/DCS,TX CTCSS/DCS can be set individually

8. TOT

9. Voice encryption(Frequency Hopping

10. Frequency Step:(2.5K/5K/6.25K/10K/12.5K/20K/25K/50K)

11. Battery saving

12. Reverse Frequency / Talk around

13. VOX

14. Busy channel lockout

15. Low battery alert / Voltage display

16. Automatic backlight

17. Channel display: Frequency/Channel/Channel name

18. Scan: Time/Carrier/Search

19. Frequency mode: Frequency difference+/Frequency difference

20. Frequency mode: Frequency difference range: 0-99.9995MHz

21. Frequency mode: Edit/Save channel specs

22. 256 memory channels

23. Emergency

24. Frequency scan

25. Scramble function

26. DTMF

27. Chinese and English display Chinese and English input method

28. Supports customization of the boot screen

Boot interface customization

（ ） Keypad description

Keypad function
Menu selection/confirmation keys：[ ]。Actual picture
Short press：To activate the menu mode, use this key to select items in the menu after entering it
Long press：To switch between channel frequency, channel number and channel name。

Move up key（]Long press to quickly change menu option, in Scan mode, change scan direction）：[ ] Actual picture
Move Down Key（]Long press to quickly change menu option, in Scan mode, change scan direction）：[ ] Actual picture

[ ]Actual picture

Short press：Switch A/B band；
Long press：In channel mode, switch channel display mode；In the input state, clear the information that has been input）。
Numeric keypad

Input information while in programming menu or input non-standard
CTCSS/DCS if need key [ ] Actual picture Short press, switch inverted frequency, off-grid, normal mode; long press for more than 2s to start frequency or channel scanning。
[ ] Actual picture Short press to enter the DTMF sending code editing interface, enter the DTMF code to be sent through the keyboard, and if it is less than 6 digits, it needs to end with the # key. After the input is complete, press PTT to send the code, short press [ ] to delete the code in edit mode，Long press [ ] to exit DTMF editing mode.
in idle state, long press for more than 2 seconds, keyboard lock or revoke keyboard lock;
In FM radio state, short press the key to search FM stations automatically.
Power/volume switch
When turning clockwise, turn on the power of the walkie-talkie; turn it counterclockwise to the end, and turn off the power of the walkie-talkie when you hear a “click”; turn clockwise to increase the volume, and vice versa to decrease.

status LED
Launch—red light on
Receive—green light on
External interface
For external headphones; or external write cable, you can use PC write software to write frequency operation and program upgrade.
Side button 1 (PTT): Press and hold to transmit, short press in alarm mode to exit alarm mode.
Side key 2 (PF2): Change the function of long press and short press of the button can be customized in the menu or writing software.
Side key 3 (PF3/MONI): change the function of long and short presses of the key can be customized in the menu or in the writing software.

（ ） Muti keys function

1. 1750Hz Tone: PTT+MONI
2. DTMF：

Screen display and Menu list

1. Screen display：

ICON defintion

strength when receiving
---|---

2. Screen display

3、Menu
1）、Menu List：

disturbed, the higher the level, the worse
the sensitivity Better  set as medium.
1| STEP| Step frequency| 5.00K| in frequency mode, to change frequency step
6.25K
10.00K
12.50K
20.00K
25.00K
2| MEMCH| Memolry channel| 000，… ，256| Delete the channel  parameters of the
specified channel If  there is no CHmeans that the channel  has no parameters
and  the operation is invalid.
3| DELCH| Channel deletion| 000，… ，256| Delete the channel parameters of the
specified channel If there is no CHmeans that the channel has no parameters and the operation is invalid.
4| R-CTCSS| Receiving analog infrasound| OFF| None DOS
---|---|---|---|---
67.0HZ, ⋯,254.1HZ| Standard CTCSS Input standard or
nonstandard CTCSS via keypa
5| R-DCS| Receiving digital
infrasound| OFF| None DCS
D023N, ⋯,D754I| Standard DCS
6| T-CTCSS| Emit analog
infrasound| 67.0HZ,
⋯,254.1HZ| Standard CTCSS Input standard or nonst-a ndard CTCSS via keypad.
7| T-DCS| Emit digital infrasound| OFF| None DCS
D023N,⋯, D754I| Standard DCS
8| VOICEPRI| Voice encryption| OFF|
Encryption 1|
Encryption 2|
Encryption 3|
9| CH-NAME| Channel name| Customizable manual  editing of  channel  names|
10| TXP| Transmit power| HIGH| High Power Transmitting
Middle| Lower Power Transmitting
LOW| Lower Power Transmitting
11| SAVE| Channel name| OFF| Off Battery saving
1| Off Battery saving
2| Normal saving
3| Super saving
12| ROGER| End of call tone| OFF| Turn off
BEEP| Turn on
TONE1200|
13| TOT| Launch time limit| 30,60,⋯480S| The number is from 30 to 480sand the
maximum time for PIT transmission
is indicated in 30s steps
14| VOX| Acoustic emission| OFF| Turn off VOX function ion.
Transmitting without PTT pressing
1,2,⋯ 9| Activate the sound pressure intensity of
voice control. level! is the most sensitive
15| W/N| channel bandwidth| WIDE| Wide mode
NARR| Narrow mode
16| VOICE| Voice prompt switch| OFF| Turn off voice prompt
ON| Turn on voice prompt
17| BEEP| Key tone switch| OFF| Turn off operation prompt
---|---|---|---|---
ON| Turn on operation prompt
18| LANGUAC; I| Menu eau I anguage| ENGLISH| ENGLISH
CHINESE| CHINESE
19| BC| Busy lock| OFF| OFF
ON| OPEN
20| SC-REV| Scanning mode| TO| Time scanning. The
walkie-talkie pauses scanning g when itdetectors a signal and after staying stopped for about 5 seconds. the
walkie-talkie will continue scanning even if the signal is still there
CO| Carrier scanning. the
two-way radio pauses
scanning when a channel is detected and keeps it on the same frequency until the
signal disappears. There is a 2 second delay between the disappearance of the signal and the resumption of
scanning to allow time for the response to begin
transmission
SE| Search scanning. the
walkie-talkie exits scanning hen it detects a signal and stays at this frequency.
21| PF2| Short press function setting of side key 2| |
22| PF2 LONG PRESS| Side key 2 long
press function setting| |
23| PF3| Short press function setting ofside key 3| |
24| I’F3 LONG
PRESS| Side key 3 long
press function setting| |
---|---|---|---|---
25| | Automatic backlight :ime setting| ON| Background light is always on
5S,10S. •| Background ON to
3Min•| automatically OFF
26| oFFSF•| Frequency difference frequency| [10.000,• • •,99.995| In frequency mode, the difference between the transmitting and
receiving frequency
27| 8FT-D| Direction of frequency difference| OFF| In frequency mode turn off the different between the transmitting and receiving frequencies
frequency| :1 mode the
TX frequency=RX plus frequency difference
| In frequency mode the TX frequency=RX plus frequency difference
28| SCAN CTCSS| Scan analog subsonic| |
29| SCAN DCS| Scan Digital Sub- tone| |
30| CDCSS SAVE MODE| Scan sub-audio save mode| ALL| All
RX| Receiving
TX| Transmitting
31| POWER ON MSG| Power screen selection| LOGO| Photo
VOLTAGE| Battery voltage
32| ANI NAME| Local name selection| NUMI . • .NUM60| Nol -No.30 radio The radio name of 31-60 can be set
33| S-CODE| DIME information c,,,1| 1,2,3-15|
34| I ‘IMP CON,| DIME, Coil()| OFF| Turn of
---|---|---|---|---
BOT| Press ‘,Tr to transmitting DTMF
EOT| Release PTT to transmitting DTMF
BOTH| Both
35| DTMFST| DTMF Code| OFF| No DTMF prompt when
press key to transmitting DTMF
DT-ST| DTMF prompt when press key to transmitting DTMF
ANI-ST| DTMF prompt when automatically transmitting and press key to transmitting DTM
DT+ ANI| DTMF prompt when automatially transmitting DTMF and press key to transmitting DTMF
36| AUTOLK| Automatic keypad lock| OFF| Turn off auto keypad lock
5S. 10S. 15S| Turn on the keypad timing automatic lock function
37| SCAN ADD| Channel scan Add| |
38| TONE| TONE voice| 1000,1450, 1750,2100H z|
39| PTT-LT| PIT late| 0,100,. • • 4000| Delay time before automatic DTMF transmitting
40| MENU EXIT TIME| Menu auto-exit time| 5,10,-•60S| Control the time of menu automatically exit
41| VOX DELAY| Voice-activated time delay| 0.5SEC• • • ..2.0SE( :|
42| R 1) STE| Over-repeat tail cancellation| OFF| Due to the delay of the repeater. noise appears
12,3,4,5,.- 105| when receive instant signal OFF: Adjust to eliminate the tail if want to ensure if the repeater is work or not set OFF
43| RPT-121.| Overtone tail delay| OFF| OFF: Adjust the length of time the tail sound appears, if not
---|---|---|---|---
1,2,3,4,5,• • • 10S| needed set it to off
44| MDF-A| A-display mode| FREQ| A band displays as, frequency in channel mode
CH| A band displays as channel in channel mode
NAME| A band displays as channel name in channel mode
45| MDF-B| B-display mode| FREQ| B band displays as frequency in channel mode
CH| B band displays as channel in channel mode
NAME| band displays as channel name in channel mode
46| TDR| Dual-frequency| OFF| Turn off
ON| Turn one
47| TX-A/R| Double-frequency transmitting option| OFF| In dual Standby mode. Transmitting current frequency band
A| IN dual standby mode press PTT to transmitting B band for cross-band TX/RX
| lAfter releasing PTT the radio will send a turn-off code to suppress the instant noise of the receive
48| STE| Tail cancellation| OFF| After releasing the PTT, the radio will send a turn-off code to suppress the instant noise of the receiver
| ON| After releasing the PTT, th
e radio will send a turn-off code to suppress the instant noise
of the receiver
49| AL-MOD| | SITE| On-site Emergency
Alarm Mode| SOUND| Send emergency voice
| CODE| Send emergency code
50| RX END TAIL| Receive end tone| OFF| OFF
---|---|---|---|---
ON| MDCl200
51| Tail Cancellation Frequency| Tail Cancellation Frequency| 55H z|
62.51-1 z|
52| SCRAMBLE| Scramble function| OFF|
SCRAM|
53| RDITANIN- AMEP| Edit local name| The name of the machine must be set in the 31-60 machine can be Edit
54| RESET| Reset| VFO| Menu back to factory setting
ALL| Menu and channel back to factory setting
55| VERSION| Version| Firmware| software
Hardware| Hardware

Note : When entering the menu, take note of whether to set A band or B band
The provisional number of menus is 55, which can be increased or decreased according to the function of the program。

Menu operation

1. Press [ ]，then enter menu key；
2. Press [ ] again to enter the menu function
3. Select option key；
4. press[ ] confirm and back to main menu
5. press[ ] to exit menu and back to normal working mode

Four. Other function description

1. Dual PTT
2. Set side key2 as PTT-B, press PTT to transmit A band press PTT-B to transmit B band.
3. AM Mode 108-136Mhz,AM mode receiving。

Scan mode
Use the side button to turn on or press and hold ［SCCAN] for more than 2 seconds to start frequency or channel scanning.
Before using scanning, you must first decide under what conditions you want the intercom to continue scanning after a signal is detected.
You can choose one of the following modes。

1. TO
   Time scanning, the walkie-talkie pauses scanning when it detects a signal, and after staying stopped for about 5 seconds, the walkie-talkie will continue scanning even if the signal is still there.。

2. CO
   Carrier scanning, the two-way radio pauses scanning when a channel is detected and keeps it on the same frequency until the signal disappears. There is a 2 second delay between the disappearance of the signal and the resumption of scanning to allow time for the response to begin transmission.
   2 SE
   Search scanning, the walkie-talkie exits scanning when detects a signal and stays at this frequency
   2、FM function
   ① )Turn on FM function, the screen will display current FM frequency。
   ②Press to change FM frequency, or input via keypad(65-108MHz); Press # key to scan FM frequency automatically in FM mode
   ③Adjust volume via Power/volume knob
   ④)Press FM key again to exit FM mode。
   Note : FM function need to be set in side key customized setting

3. Frequency scan
   Scan other radio’s CTCSS/DCS and frequency to make a contact。
   After defining the side key function as a frequency scan function，turn it on through the side key. This function can scan the frequency of U/V/200M/350M, and switch the frequency, it will continue to scan CTCSS/DCS. If there is no CTCSS/DCS, the screen will display NONE ‘and end the scan. At this time, the Scanned data can be saved to the designated channel through the[ ]key and the frequency scan function can be launched .
   Or though[ ]or[ ]to start the next frequency scan.DTMF 。

4. NOAA Function
   After defining the side key function as the weather forecast function, the function can be turned on by the side key with 10 sets of fixed frequency points built-in, which pressed key to select the frequency you want to receive
   Note : NOAA weather forecast feature is only available in countries and regions that support NOAA channels。

5. DTMF
   DTMF transmitting
   Quick transmitting Encode: In transmitting status, press digit keys、 ，to transmit DTMF encode 0-9、
   ABCD#。Press key to continuously encode transmitting，and release to end encode transmittingTransmitting encode after editing: In standby mode, press# key to enter DTMF edit menu, input DTMF code 0-9、ABCD#，
   less 6 digits then press # as ending. Done editing, press PTT to transmitting DTMF. In edit mode press [ ] to delete encode, then press，then long press [ ] to exit DTMF edit mode B.DTMF Decode

6. ANI Name Display
   This function is mainly used to display the name of the current transmitter, so as to determine which machine is currently transmitting; the machine has 60 built-in groups of names to choose from, 30 groups are fixed from No. 1 to No. 30; 30 groups (31-60 groups) can be customized by the user, and the name can be set in the identity code code group of the frequency writing software. select own radio Name, menu item 32 (local name selection) to select the local name, the local name has 1 machine to 30 machines, and 30 groups of user- defined names (set in the identity code code group settings of the writing frequency software).

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>