Abyss B0B9H7FVCZ 360 Photo Booth Machine for Parties Instruction Manual
- June 15, 2024
- ABYSS
Table of Contents
Abyss B0B9H7FVCZ 360 Photo Booth Machine for Parties
Product Information
Specifications
- Product Name: 360 Infinity Photo Booth
- Package Contents : Photo booth, accessories
- Power Supply : DC connector
- Power Cord : AC100-240V
- Portable Charger Output : DC5V
- Battery Specifications:
- Booth Remote : 23A 12V
- LED Remote : CR2025 3V
- Ring Light : DC5V USB Portable Charger
Product Usage Instructions
Installation
- Open the package and take out all the accessories.
- Put the 360 photo booth upright.
- Adjust the height of the cushions to keep the 360 photo booth stable.
- Put the shaft into the balance board.
- Fix it with 2 M8 screws on the left and right sides respectively.
- Install the ring light on the head of the thinner pole.
- Tighten the head screws.
- Plug the male connector of the power supply into the DC connector from the booth.
- Plug the power cord and the power supply.
- Put the portable charger (DC5V output, not provided with the booth) in the bending pole box.
- Plug the USB plug of the ring light into the power bank.
- Press the on/off button on the power bank one time.
- Insert the three plugs of the power cord into AC100-240V and the installation is complete!
Notice
- Reverse rotation and speed can be adjusted through the motor remote control.
- The color of the ambient strip light can be changed by the LED remote controller.
- The medium pole can be removed if needed, then connect the large pole with the small pole directly.
INSTALLATION INSTRUCTIONS
360 Infinity Photo Booth
- Open the package and take out all the accessories.
- Put the 360 photo booth upright. Adjust the height of the cushions to keep the 360 photo booth stable.
- Put the shaft into the balance board. And fix it with 2 M8 screws on the left and right sides respectively.
- The bending pole (with the box opening facing up) is mounted on the shaft. First, use M8 screws to fix the left and right center positions. Adjust the appropriate angle, and then fix the edges on both sides with M8 screws
- Install thicker pole + thinner pole or install thinner pole to the bending pole directly (thicker pole is not necessary)
- 5.1 Insert the thicker pole into the bending pole. The left and right sides are fixed with 2 M6 screws respectively. Then insert the thinner pole into the thicker pole. The left and right sides are fixed with 2 M6 screws respectively. By adjusting the corresponding hole position, the height can be adjusted
- 5.2 Insert the thinner pole directly into the bending pole. The left and right sides are fixed with 2 M6 screws respectively. By adjusting the corresponding hole position, the height can be adjusted.
- Install the ring light on the head of the thinner pole. Tighten the head screws.
- Plug the male connector of the power supply into the DC connector from the booth. Plug the power cord and the power supply
- How to install mobile phone, camera, and iPad (choose one of three)
- 8.1 Mobile phone installation. Install the phone holder assembly on the central screw hole of the ring light, pull out the ends of the phone holder, and put the phone into the slot.
- 8.2 Camera installation. install the camera on the pan/tilt in the middle of the ring light. Tighten the gimbal screws.
- 8.3 iPad installation. Install the iPad holder assembly on the thinner pole and tighten the fixing screws. Press the button on the side of the stand and pull out the buckle. Put the iPad into the slot, and then tighten the buckle.
- Put the portable charger (DC5V output, not provided with the booth) in the bending pole box. Plug the USB plug of the ring light into the power bank. Press the on/off button on the power bank one time.
- Insert the three plugs of the power cord into AC100-240V and the installation is complete!
NOTICE：
- Reverse rotation and speed can be adjusted through the motor remote control. The color of the ambient strip light can be changed by the LED remote controller.
- All batteries do not come with the photo booth and need to be purchased by the customer. Battery for remote control with lamp (battery specification CR2025 3V) Battery for motor remote control (battery specification 23A 12V) Battery for ring light ( battery specification 5V USB)
- The medium pole can be removed if needed, then connect the large pole with the small pole directly.
FAQ’s
Are batteries included with the photo booth?
No, all batteries need to be purchased separately by the customer. The
battery specifications are as follows:
- Booth Remote: 23A 12V
- LED Remote: CR2025 3V
- Ring Light: DC5V USB Portable Charger
Note : All batteries do not come with the photo booth and need to be purchased by the customer.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>