EUREKA ERK-G47 Music Sensing RGB LED Lights Glass Gaming Standing Desk User Manual

EUREKA ERK-G47 Music Sensing RGB LED Lights Glass Gaming Standing Desk

PARTS

**HARDWARE

ASSEMBLY INSTRUCTIONS
**

OPTIONAL ACCESSORY MONITOR ARM INSTALLATION

KEYPAD INSTRUCTIONS

OPERATING INSTRUCTIONS

• Adjust the Height

  • When you press”/\”, the desk goes upward until it reaches the highest point.
  • When you press” V “, the desk goes downward until it reaches the lowest point.
  • When you press “/\” or” V” briefly, the desk goes a small distance correspondingly.

• Set Memory Heights
  Set the height: 2 memory heights can be saved as follows.

  • Adjust the desktop to the desired height.
  • Press “1” or “2” for 4 seconds until “S-1” or “S-2” flashes.
  • Memory height inquiry: press “1” or “2” briefly and the corresponding memory height will flash.
  • Adjust the desk to the memory height: double-press “1” or “2” and the desktop will automatically move to the corresponding memory height. Pressing any button will stop the process.

• Set the Minimum Height
  Set the minimum height: the minimum height of the desk can be set to avoid collision. If the desktop reaches the minimum height, the display will show”- Lo”. The procedure is as follows.

  • Adjust the desk to the desired height.
  • Press “2” and” V” for 5 seconds until the display shows”- d o”.
  • Disable the saved minimum height:
  • Method 1: refer to the Initial Setup procedure.
  • Method 2: Adjust the desk to the minimum height. Press” V” and “2” for 5 seconds until the display shows”- d o”.

• Set the Maximum Height
  Set the maximum height: the maximum height of the desk can be set to avoid collision. If the desktop reaches the maximum height, the display will show”- H I”. The procedure is as follows.

  • Adjust the desk to the desired height.
  • Press”/\” and “1” for 5 seconds until the display shows”- u p”.
  • Disable the saved maximum height:
  • Method 1: refer to the Initial Setup procedure.
  • Method 2: a. Adjust the desk to the maximum height. b. Press 11 /\” and “1” for 5 seconds until the display shows”- u p”.

• Initial Setup
  (Perform this procedure in normal operation, or when the control box is replaced for the first time) Press 11 /\” and II V II at the same time until the display shows”- – -“. The system will enter the initialization mode and the desk will automatically move up and down. Once the desk stops, the initial setup process is complete.

• Factory Reset
  (Perform this procedure when the error code “El 2”, “El 6” or “rST” occurs) Press II V” for 5 seconds until the display shows”- – -” and the system will enter the reset mode. The desk will automatically move to its lowest height regardless of the previously set height limits and then rise to a pre- programmed height. Once the desk stops, the reset process is complete.

LIGHTS OPERATING INSTRUCTIONS

Connect to Eureka Light

1. Make sure that you turn on Bluetooth and location services on your phone or tablet.
2. Open the app–Tap “Rescan Control” to refresh the device list–find the device named “EUKLED”–Tap “Connect”. To rename the device, you can tap and hold the device name.
3. Tap the device name to start controlling the lights.

Change modes
Press on the control panel to change modes. Each press will lead to a different mode. 38 modes are available. Starting from static red, the first 12 modes are standard lighting effects, and the last 26 modes are music spectrum lighting effects.

Turn on/off the lights

Press and hold on the control panel for about 2 seconds and the lights will be turned on/off.

LIGHTING FUNCTIONS

• Friendly remote control on a mobile app.
• 27 music spectrum lighting effects, 1 static standard effect, and 10 dynamic standard effects.
• Save settings in case of power failure.
• Change modes and turn on/off the lights at the touch of a button.
• Sleep mode: select “Sleep Mode” on the app and the lights will turn warm yellow. The lights gradually dim over time. After 15 minutes, the light disappears and the system automatically shuts down.

DOWNLOAD THE LIGHTING APP

This controller is controlled via a mobile app, which works on iOS and Android. Apple phones: require iOSl 0.0 or later; Android phones: require ANDROID4.4 or later. For Apple phones, please search for “Eureka Light” in App Store. For Android phones, please type the web address http://www.designa.cn/app/Eureka0520.apk in your browser to download the app directly.

ERROR CODES AND TROUBLESHOOTING

ERROR CODES

E01, E02

| CAUSE

Loose connection between the legs and the control box

|

SOLUTION

1.  Press”/\”or”V”again. Ifthe code still exists, please check whether the leg cables are loose.

2.  lfthe code still exists after step 1, please switch the leg cables. Ifthe code does not change, the control box is faulty. Ifthe code changes (eg: E0l-> E02 or E02-> E0l), the leg is faulty. Please contact our local customer service team for replacement parts.

---|---|---

E03, E04

| ****

Overload or motor failure

| ****

Please switch the leg cables. Ifthe code does not change, the control box is faulty. Ifthe code changes (eg: E03 -> E04 or E04 -> E03), the leg is faulty. Please contact our local customer service team for replacement parts.

E05, E06

| ****

Faulty leg sensor

| ****

1.  Press”/\”or”V”again. Ifthe code still exists, please check whether the leg cables are loose.

2.  lfthe code still exists after step 1, please switch the leg cables. Ifthe code does not change, the control box is faulty. Ifthe code changes (eg: E0S-> E06 or E06-> E0S), the leg is faulty. Please contact our local customer service team for replacement parts.

E07

| ****

Faulty power supply ofthe control box

| Unplug the desk and plug it back in after 10 seconds. Ifthe code still exists, the control box is faulty. Please contact our local customer service team for replacement parts.

E08, E09

| ****

Faulty leg

| Unplug the desk and plug it back in after 10 seconds. Ifthe code still exists, the control box is faulty. Please contact our local customer service team for replacement parts.

E10, E11

| ****

Faulty control box

| Unplug the desk and plug it back in after 10 seconds. Ifthe code still exists, the control box is faulty. Please contact our local customer service team for replacement parts.

E12

| ****

Faulty leg position

| ****

Factory reset: press” V” for about 5 seconds until the display shows”- – -“.

E13| Overheat protection| Please wait for the temperature to drop before use.

E14, E15

| ****

Leg stuck

| ****

Please switch the leg cables. Ifthe code does not change, the control box is faulty. Ifthe code changes (eg: El4 -> El5 or El5 -> El4), the leg is faulty. Please contact our local customer service team for replacement parts.

E16

| ****

Unbalanced legs

| ****

Factory reset: press” V” for about 5 seconds until the display shows”- – -“.

E17

| ****

Key data ofthe control box lost

| Unplug the desk and plug it back in after 10 seconds. Ifthe code still exists, the control box is faulty. Please contact our local customer service team for replacement parts.

rST

| Control box system suddenly turning off| ****

Factory reset: press” V” for about 5 seconds until the display shows”- – -“.

The display does not work after the desk is plugged in.

| ****

Faulty control box or poor electrical contact;

Faulty power supply or loose connection, etc.

| ****

Check the power cord and whether the connection between the control box and the power supply is loose (to replug all cables is recommended). Ifthe display still does not work properly, please contact our local customer service team for replacement parts.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>