AIMIBO G57 Wireless HDMI Transmitter and Receiver User Manual

AIMIBO G57 Wireless HDMI Transmitter and Receiver

Product Information

The product is called “Dirt Eater” and it is a tool designed for cutting and removing dirt or grime from surfaces. It features a blade with multiple slots of different sizes, allowing users to adjust the cutting depth based on their needs. The Dirt Eater is made with a carefully chosen and optimized polymer that makes it flexible, unbreakable, and lightweight.

Specifications

• Material: Optimized polymer
• Blade Slots : Multiple slots of different sizes
• Weight: Minimal and lightweight

Preface

Thank you for purchasing our products, For optimum operation, please read this manual carefully before use.

Features

1. Wireless transmit and receive Simply connect the transmitter of this product to a computer, camera, or any other video output device equipped with an HDMI output port, and connect the receiver to an LCD TV, Projector, or other display device with an HDMI input port to realize wireless screen casting.
   The product has been paired out of the factory. It will start working after a simple connection. No need for troublesome software setup.

2. Allows switching/addition of transmitters
   Up to eight separate transmitters can be added through simple pairing operations (available through separate purchase), and different transmitters can be switched at the push of a button.

Package Includes

Name of each part

Receiver-RX

Transmitter-TX

How to connect

STEP 1: Connection of the Receiver(RX)

1. Connect the USB Charging cable to the Receiver(RX) and power it with a 5V / 2A AC adapter.
2. Connect the HDMI port of the Receiver(RX) to the TV/projector, etc.
3. Wait a few seconds, and the system screen will appear on the monitor.

If the system screen is not displayed, please confirm the HDMI signal source of the TV.

Example: When the HDMI port is connected to the “HDMI 2” port of the monitor, please switch the “Signal Source” of the monitor to “HDMI 2”.

STEP 2: Connection of the Transmitter(TX)

1. Connect the HDMI port of the Transmitter(TX) to the PC/Laptop, etc.
   • In case the HDMI output port cannot supply sufficient voltage to the transmitter, an external AC adapter (voltage: 5V 2A) is required to power the TX.
2. After the indicator light flashes rapidly, wait for about 10 seconds and the projection is completed.

How to repair

The product will be paired at factory inspection. If pairing fails or if you need to pair again in other cases, please refer to the following:

1. Please connect the receiver to the monitor and the power supply. Connect the transmitter to the PC device and power supply.
2. Please press and hold the receiver function button for more than 3 seconds, the interface pops up the message: Release the button to pair with EZCast TX. At this time the receiver enters the pairing mode and wait for the transmitter to connect. Press and hold the transmitter function button for more than 5 seconds, the indicator light appears flashing for pairing, and the transmitter indicator light is always on when the connection is successful.
3. Pairing is complete when “Pairing-OK” is displayed on the monitor. After waiting for a few seconds, the picture from the transmitter will be automatically output to the receiver.

Note: One receiver can be paired with up to 8 transmitters.

How to reset

How to reset the receiver:
Press and hold the function button of the receiver for more than 10 seconds to reset.

• There is no need to re-pair with the transmitter. How to reset the transmitter:
  Press and hold the function button of the transmitter for more than 10 seconds to reset it

• Need to re-pair with the receiver.

transmittersHow to switch

In the state of multiple transmitter pairing, press the function button of the transmitter to turn off the screen.

1. Press the “function button” of the working transmitter, and the screen at the receiving end will return to the system screen.
2. Press the “function button” of the transmitter you want to switch to achieve screen switching.

QuestionsFrequently Asked

1. The wireless HDMI transmitter and receiver can not work properly.
   • Pairing is unpaired.
   • Please try to re-pair.
   • The antenna signal of the receiver is not read properly.
   • Please re-insert the connection order of the receiver in the following order.
   • Connect the USB port of RX and power supply first, then connect the HDMI port and monitor.
   • Insufficient power supply.
   • Please use the 5V2A adapter to supply power to the transceiver.
2. Unable to pair.
   • The antenna signal of the receiver is not read properly.
   • Please re-insert the connection of the receiver with the following steps.
   • Connect the USB port of RX and power supply first, then connect the HDMI port and monitor.
3. The screen frequently returns to the initial screen.
   • Check and set the device (PC) connected to the transmitter not to enter the hibernation state.
   • Please reconnect the transmitter with an AC adapter of 5V/2A or more.
4. When communication is interrupted during use due to the heat generation of the transmitter, it takes some time to resume.
   • The power supply to the transmitter is insufficient. Please use 5V/2A adapter to supply power to the transmitter.
   • TX will not work temporarily due to overheating protection if it is used for a long time.
5. Only the image is transmitted, but not the sound.
   • Check whether the stereo sound is turned on, please turn off the stereo sound.
   • Please enter the system settings of the transmitter device -> Sound -> Switch the speaker.

Customer Support

Support for product issues: info@Aimibo.tv

FCC Statement

FCC Warning Statement
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

RF Exposure Statement To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and operated at a minimum distance of 20cm from the radiator of your body. This device and its antenna(s) must not be co-located or operated in conjunction with any other antenna or transmitter.

ISED Statement
English: This device complies with Industry Canada license-exempt RSS standard(s).

Operation is subject to the following two conditions:

1. This device may not cause interference,
2. This device must accept any interference, including interference that may cause undesired operation of the device.

The digital apparatus complies with Canadian CAN ICES-3 (B)/NMB-3(B).

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>