Little GIANT WGP-55 WGP Pond Pump Instructions
- June 14, 2024
- Little Giant
Table of Contents
Little GIANT WGP-55 WGP Pond Pump
Specifications
- Mode l: WGP-55/65/75/95
- Voltage: 230V
- Frequency: 50Hz
INTRODUCTION
This instruction sheet provides you with all the information required to safely own and operate your new Little Giant Pump. The pump you have purchased is made of the highest quality workmanship and material. It has been engineered to give you long and trouble-free service. Only minimal maintenance of cleaning the intake screen of debris, which restricts the intake of the pump, is required (See part 6 of the Service section for instructions on how to perform this). This pump has the unique design feature of having dual 1-1/4” BSPT (GAS) discharges and has been designed to operate waterfalls, streams, and fountainheads or just circulate the water in your pond. The uniqueness of the dual discharges will allow the possibility of performing two of the above tasks at the same time without having to purchase two pumps. The pump has included it a cap plug that will allow one of the discharges to be closed if only one discharge is to be utilized. An elbow adapter is also included to adapt from the discharge of the pump to either 1” smooth tubing WGP-55/65 or 1-1/4” smooth tubing WGP-75/95, depending on the model of pump chosen. The pump can either be installed in the upright or vertical position or it can be installed in the horizontal position lying on the base. Little Giant pumps are carefully inspected and packaged to ensure safe operation and delivery. When you receive your pump, examine it carefully to determine that there are no broken or damaged parts that may have occurred during shipment. If damage has occurred, make a notation and notify the firm from which you purchased the filter. They should assist you in the repair or replacement of the pump. If not, please do not hesitate to contact Little Giant Customer Service at 1-888-956-0000. Please have the model number, catalog number, and serial number of the pump before you call. This can be found on the serialized label on top of the pump. They should be able to assist you further
OPERATION
- Place the pump fully submerged on a solid surface. If the surface is dirt or sand, place the pump on a flat surface such as a brick or stone to prevent it from being clogged.
- Conformity with local and state electric codes is mandatory. The National Electric Code requires that a ground fault circuit interrupter (GFCI) be used in the branch circuit supplying sump, utility, effluent, and all fountain pumps, pool pumps, and other pond equipment.
- Do not allow the unit to run dry. Damage will result and void the warranty.
- The pump is supplied with a grounding conductor and a grounding-type attachment plug.
- The pump motor is designed for 230 Volt/50Hz operation. Be certain the supply voltage is the same. The motor is a single voltage only.
- The discharge on the WGP series pumps is threaded for 1-1/4” pipe.
- The WGP-55/65 series units are supplied with a 1” barbed elbow that is screwed into the discharge of the pump. The WGP-75/95 unit is supplied with a 1-1/4” barbed elbow that attaches to the discharge. Flow is reduced by approximately 20% when these elbows are used
SERVICE: MAKE CERTAIN THE UNIT IS DISCONNECTED FROM THE POWER SOURCE BEFORE ATTEMPTING TO SERVICE OR REMOVE ANY COMPONENT!
- This Appliance has no user-serviceable parts. The motor housing of the pump is completely sealed and requires no service. Disassembly of the motor housing or alteration of the power cord voids all warranty. The power cord on these units cannot be replaced.
- The motor is permanently sealed without oil and contains an automatic thermal overload protector device.
- The unit can run continuously as long as water is pumped. If the unit runs more than 2 to 3 minutes without pumping water, damage to the shaft will occur.
- Do not pump heated liquids. Maximum temperature is 35°C (95°F). The WGP series is best suited for pumping fresh water while completely submerged for proper cooling. The pump can run in shallow water for short periods as long as the inlet screen is totally submerged.
- Be certain that the volute is flooded before plugging the unit in.
- A clogged or dirty intake screen will greatly reduce performance. If the pump is used on a dirty surface, raise it slightly to reduce the amount of debris contacting the intake. To clean the intake screen, first make sure the pump is unplugged from any power source, then remove the bottom plate by placing a finger in one of the screen holes between the plate and the intake screen. Then use your finger to “pop” the plate out of the intake screen. This should require minimal force and should pop out of the center of the intake. Then clear all of the debris from intake and any other areas that need clearing. After clearing the debris for the screen replace the plate by inserting the center tab on the plate into the center hole on the intake screen and “pop” it back into place by pressing on the center of the outside of the plate.
- If less flow is desired restrict the discharge flow. Never restrict the pump’s intake.
- Be certain the power cord is in good condition and contains no nicks or cuts.
- Refer to the troubleshooting chart if the unit is not operating properly.
- GROUNDING INSTRUCTIONS: A Residual Current Device (RCD) also known as a Residual Current Breaker (RCCB) having a tripping current not exceeding 30mA must be installed in the supply circuit. RISK OF ELECTRIC SHOCK This pump is supplied with a grounding conductor and grounding-type attachment
TROUBLESHOOTING INFORMATION
PROBLEM • **| PROBABLE CAUSES •| SOLUTIONS**
The pump does not run.| 1. Power cord unplugged.
2. Impeller jammed.
| 1. Plug the cord securely into the socket and check if there is voltage on the line.
2. Disconnect power cord. Remove the bottom plate and remove foreign objects.
The pump runs but does not deliver water.| 1. Water level under minimum suction level.
2. Air trapped in the pump during initial installation or when the pump ran dry.
3. The suction screen is clogged.
4. Discharge line clogged or obstructed
| 1. Stop the pump.
2. Disconnect power cord. Get the air out by submerging the pump in a tilted position and shaking it with the discharge tube open.
3. Disconnect power cord. Clean the screen.
4. Disconnect power cord. Remove and clean the discharge line.
The pump stops running automatically.| The thermal overload protection system stopped the pump due to the following possibilities:
• Pump suction clogged.
• The pump was used to pump hot water.
• The pump ran dry
| Disconnect the power cord. Correct the reason for overheating. Wait until the pump is cooled. Plug in the cord and resume operation.
REPLACEMENT ITEMS
ITEM| DESCRIPTION| P/N
1| Plate| 170208
2| Elbow 1” Barbed| 170170
2| Elbow 1¼” Barbed| 170194
3| Plug Cap 1¼” GAS| 170245
4| Handle, Base| 170210
LIMITED WARRANTY
THIS WARRANTY SETS FORTH THE COMPANY’S SOLE OBLIGATION AND THE PURCHASER’S
EXCLUSIVE REMEDY FOR DEFECTIVE PRODUCTS.
Franklin Electric Company, Inc. and its subsidiaries (hereafter “the Company”)
warrant that the products accompanied by this warranty are free from defects
in materials or workmanship of the Company that exist at the time of sale by
the Company and which occur or exist within the applicable warranty period.
Any distributor, sub-distributor, recipient, end-user, and/or consumer agrees
that by accepting the receipt of the prod-ucts, the distributor, sub-
distributor, recipient, end user and/or consumer expressly agrees to be bound
by the terms of the warranty set forth herein.
Applicable Warranty Period
The products accompanied by this warranty shall be covered by this Limited
Warranty for a period of 24 months from the date of original purchase by the
consumer. In the absence of suitable proof of purchase date, the warranty
period of this product will begin to run on the product’s date of manufacture.
Instructions Applicable to this Limited Warranty
- Consumers wishing to submit a warranty claim must return the products accompanied by this warranty to the point of purchase for warranty consideration.
- Upon discovery of a defect, any personal injury, property damage or any other type of resulting damage, if applicable, shall be reasonably mitigated to the extent possible.
- At its discretion, the Company may inspect products either at its facilities or in the field, and after determination of a warranty claim, will, at its option, repair or replace defective parts. Repaired or replaced parts will be returned freight prepaid by the Company.
- This warranty policy does not cover any labor or shipping charges. The Company shall not be liable for any costs or charges attributable to any product testing, maintenance, installation, repair or removal, or for any tools, supplies, or equipment needed to install, repair, or remove any product.
Warranty
Limitations Applicable to this Limited Warranty
THIS WARRANTY DOES NOT APPLY TO ANY OF THE FOLLOWING:
- Any product that is not installed, applied, maintained and used in accordance with the Company’s published instructions, applicable codes, applicable ordinances and/or with generally accepted industry standards.
- Any product that has been subject to misuse, misapplication, neglect, alteration, accident, abuse, tampering, acts of God (including lightning), acts of terrorism, acts of war, fire, improper storage or installation, improper use, improper maintenance or repair, damage or casualty, or to an excess of the recommended maximums as set forth in the product instructions.
- Any product that is operated with any accessory, equipment, component, or part not specifically approved by the Company.
- Use of replacement parts not sold by the Company, the unauthorized addition of non-Company products to other Company products, and the unauthorized alteration of Company products.
- Products damaged by normal wear and tear, normal maintenance services and the parts used in connection with such service, or any other conditions beyond the control of the Company.
- Any product that has been used for purposes other than those for which it was designed and manufactured.
- Any use of the product where installation instructions and/or instructions for use were not followed.
The Company reserves the right at any time, and from time to time, to make
changes in the design and/or improvements upon its product without thereby
imposing any obligation upon itself to make corresponding changes or
improvements in or upon its products already manufactured and/or previously
sold. The Company further reserves the right to substitute parts or components
of substantially equal quality in any warranty service required by operation
of this Limited Warranty.
This written Limited Warranty is the entire warranty authorized and offered by
the Company. There are no warranties or representations beyond those expressed
in this document.
THIS WARRANTY AND REMEDY IS IN LIEU OF ALL OTHER WARRANTIES AND REMEDIES INCLUDING WITHOUT LIMITATION, WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR PURPOSE, WHICH ARE HEREBY SPECIFICALLY DISCLAIMED AND EXPRESSLY EXCLUDED. CORRECTION OF NON-CONFORMITIES, IN THE MANNER AND FOR THE PERIOD OF TIME AS SET FORTH ABOVE, SHALL CONSTITUTE FULFILLMENT OF ALL LIABILITY OF THE COMPANY TO THE PURCHASER WHETHER BASED ON CONTRACT, NEGLIGENCE, OR OTHERWISE.
THE COMPANY SHALL NOT BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL OR SPECIAL
DAMAGES SUCH AS, BUT NOT LIMITED TO:
DAMAGE TO OR LOSS OF OTHER PROPERTY OR EQUIPMENT, LOSS OF USE OF EQUIPMENT,
FACILITIES OR SERVICE, LOSS OF PROFIT OR SALES, COST OF PURCHASES OR
REPLACEMENT GOODS, CLAIMS OF CUSTOMERS OF THE PURCHASER, FAILURE TO WARN
AND/OR INSTRUCT, LOSS OF OTHER PRODUCTS, OR COSTS OF ENVIRONMENTAL
REMEDIATION, OR DIMINUTION IN PROPERTY VALUE. THE REMEDIES OF THE PURCHASER
SET FORTH HEREIN ARE EXCLUSIVE, AND THE LIABILITY OF THE COMPANY SHALL NOT,
EXCEPT AS EXPRESSLY PROVIDED HEREIN, EXCEED THE PRICE OF THE PRODUCTS UPON
WHICH SUCH LIABILITY IS BASED.
DAMAGES AS SET FORTH IN THIS PARAGRAPH SHALL BE REASONABLY MITIGATED TO THE EXTENT POSSIBLE. THIS PARAGRAPH SHALL ALSO APPLY TO ALL DAMAGES RESULTING FROM CONDITIONS SET FORTH IN SECTION III ABOVE AND (1) DEFECTS IN PRODUCT PROTOTYPES OR REPLACEMENT PART PROTOTYPES THAT HAVE NOT BEEN PUT INTO PRODUCTION, CIRCULATED AND SOLD BY THE COMPANY, AND/OR (2) DEFECTS
THAT WERE NOT FOUND AT THE TIME OF SALE DUE TO SCIENTIFIC AND TECHNOLOGICAL REASONS.
This Limited Warranty gives you specific legal rights. You may have other rights, which vary according to the applicable laws and regulations. Where any term of this warranty is prohibited by such laws, it shall be null and void, but the remainder of this warranty shall remain in full force and effect.
DISCLAIMER : Any oral statements about the product made by the seller, the Company, the representatives or any other parties, do not constitute warranties, shall not be relied upon by the user, and are not part of the contract for sale. Seller’s and the Company’s only obligation, and buyer’s only remedy, shall be the replacement and/or repair by the Company of the product as described above. Before using, the user shall determine the suitability of the product for his intended use, and the user assumes all risk and liability whatsoever in connection therewith.
www.lg-outdoor.com
customerservice@lgpc.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>