SEALEY PW1610 Pressure Washer Instruction Manual

SEALEY PW1610 Pressure Washer

Specifications

• Fuse Rating : 13 Amp
• Plug Type : BS1363/A 3-pin plug

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble-free performance.

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

SAFETY

ELECTRICAL SAFETY

WARNING: It is the user’s responsibility to check the following:
Check all electrical equipment and appliances to ensure that they are safe before use. Inspect power supply leads, plugs and all electrical connections for wear and damage. Sealey recommend that an RCD (Residual Current Device) is used with all electrical products. You may obtain an RCD by contacting your local Sealey Stockist.

If the product is used in the course of business duties, it must be maintained in a safe condition and routinely PAT (Portable Appliance Test) tested. For electrical safety information, it is important that the following information is read and understood.

• Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.

• Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.

• Important: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the correct fuse – see fuse rating in these instructions.

• DO NOT pull or carry the appliance by the power cable.

• DO NOT pull the plug from the socket by the cable. Remove the plug from the socket by maintaining a firm grip on the plug.

• DO NOT use worn or damaged cables, plugs, or connectors. Ensure that any faulty item is repaired or replaced immediately by a qualified electrician.

• This product is fitted with a BS1363/A 3-pin plug.
  If the cable or plug is damaged during use, switch the electricity supply and remove it from use.
  Replace a damaged plug with a BS1363/A 3-pin plug. If in doubt contact a qualified electrician.
  Class II products are wired with live (brown) and neutral (blue) only, and are marked with the Class II symbol.

  • A) Connect the BROWN live wire to the live terminal ‘L’.
  • B) Connect the BLUE neutral wire to the neutral terminal ‘N’.
  • C) After wiring, check that there are no bare wires and ensure that all wires have been correctly connected.
    Ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.

• DO NOT connect either wire to the earth terminal.
  Sealey recommends that repairs be carried out by a qualified electrician.

GENERAL SAFETY

• WARNING! Water and electricity are dangerous partners. Be extremely cautious and ALWAYS be aware that this device uses an electric motor. Always plug into an RCD (See electrical safety above). Unplug from mains before changing accessories or servicing.

• The appliance can be used for washing surfaces outdoors, whenever pressurized water is required to remove dirt.

• This appliance is for outdoor use only.

• Ensure you comply with all local water supply regulations. Power washers may only be connected to the mains water supply if a check valve is installed in the supply hose, or at the tap outlet.

• The supply hose must be reinforced, and have an internal diameter of 1/2”. The water supply must be at least equal to the cleaner capacity. The water temperature must NOT exceed 122°F (50°C). The water supply pressure must NOT exceed 6 bar (90psi).

• Always be aware of the hazards that may occur during use. Study all applications and limitations of the washer before use.

• Use where air can freely circulate around the washer to avoid the machine overheating.

• DO NOT obstruct ventilation grilles during operation.

• Position the washer as near to the water supply as possible.

• WARNING: Always disconnect the electricity and water supplies on completion of every job and before performing maintenance.

• WARNING! DO NOT use the washer if any part of the unit, gun, nozzle, detergent tank, hose or cables is damaged. Replace or repair using genuine parts only. Unauthorized parts may be dangerous and will invalidate your warranty. Always check connections are correctly secured and not cracked or damaged in any way before using the machine.

• WARNING: This appliance has been designed for use with the detergent specified by the manufacturer. The use of other detergents or chemicals may put the appliance’s safety at risk.

• WARNING! Ensure all persons and animals keep at a minimum distance of 15m from the washer when in use. All persons within 15m shall wear appropriate P.P.E.

• Wear adequate protective clothing, goggles, and anti-slip rubber-soled footwear.

• DO NOT touch the plug and the appliance with wet hands or when barefoot.

• DO NOT direct the nozzle toward mechanical parts containing lubricant grease, as the grease will dissolve and spread over the surrounding ground. Vehicle tires/tyre valves may only be cleaned from a minimum distance of 30 cm, otherwise, the vehicle tire/ tyre valve could be damaged by the high-pressure jet. The first indication of this is a discoloration of the tire.  Damaged vehicle tires/tire valves can be deadly

• WARNING: High-pressure jets can be dangerous if subject to misuse. The jet must not be directed at persons, animals, live
  electrical equipment or the machine itself.

• WARNING! The high-pressure jet will cause loose particles to be propelled at high speed, which may cause serious injury.

• WARNING: High-pressure hoses, fittings, and couplings are important for the safety of the machine. Use only hoses, fittings and couplings recommended by the manufacturer. (it is extremely important to protect these components against damage by avoiding their improper use and protecting them against bending, knocks and scratches).

• The appliance can be used for washing surfaces outdoors, whenever pressurized water is required to remove dirt.
  WARNING: This appliance is equipped with T.S.– Total Stop: these appliances should not be left in standby for more than 5 minutes.

• WARNING! DO NOT operate the machine without a water supply. Dry running can seriously damage the unit.

• Switch the appliance off completely (master switch on (0) OFF) whenever it is left unattended.

• Every machine is tested in its operating conditions, so it is normal for a few drops of water to be left inside it.

• Take care not to damage the electric cable. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard

• DO NOT move the unit by pulling the hoses or electrical cables. Use the handle.

• Appliance with fluid under pressure. Keep a firm hold on the gun and be prepared to take the kickback pressure. Only use the high-pressure nozzle provided with the appliance.

• Children should be supervised to ensure that they DO NOT play with the appliance.

• DO NOT start the high-pressure cleaner without first completely unwinding the high-pressure hose.

• WARNING: When winding and unwinding the hose take care not to cause the high-pressure cleaner to overturn.

• Before unwinding or winding the hose, switch the machine off and release the pressure in the hose itself (switching off).

• DO NOT use the washer with flammable or toxic liquids or any other product. Use only recommended detergent. Unapproved detergents may corrode the machine cover and accessories.

• DO NOT spray flammable liquids at risk of explosion.

• DO NOT direct the jet against yourself or others in order to clean clothes or footwear.

• WARNING: Water that has flowed through backflow preventers is considered to be nonpotable.

• WARNING! The pressure washer must only be used with clean water. Unfiltered water or corrosive chemicals must not be used as
  these will damage the cleaner.

• WARNING: Improper extension cables can be dangerous. If an extension cord is used, it must be suitable for outdoor use, and the connection must be kept dry and clear of the ground. It is recommended that this be done using a cable reel that holds the plug at least 60 mm from the ground.

• If an extension cord is used, the plug and socket must be of watertight construction.

• If, during operation, a power failure occurs turn the electricity and water off for safety reasons.

• WARNING: During the use of high-pressure cleaners, aerosols may form. Inhalation of aerosols can be dangerous to health.

• WARNING: Depending on the application, shielded nozzles can be used for high-pressure cleaning, which will drastically reduce the emission of hydrated aerosols. However, not all applications allow the use of such a device. If the armored nozzles are not applicable for aerosol protection, a respiratory mask of class FFP 2 or equivalent may be necessary, depending on the cleaning environment

• WARNING: the gun is fitted with a safety catch.

• Whenever use of the machine is interrupted it is important to operate the safety catch to prevent accidental activation of the jet.

• Safety features: gun equipped with safety locking device, appliance equipped with (Class I) overload cut out, pump equipped with
  by-pass valve or shutdown device.

• The safety button on the gun is not there to lock the lever during operation but to prevent its accidental operation.

• Ensure the nozzle is aimed correctly at the work surface before switching on the machine.

• Before activating the trigger, grip the gun firmly to counteract the recoil from the high-pressure water jet.

• WARNING! Avoid sudden bursts of water as these will cause water pressure to drop and put extreme pressure on hoses and connectors.

• WARNING: The appliance is equipped with a motor protection device: in case of device intervention, wait some minutes or, in the alternative, disconnect and re-connect the product to the electric system. In case this problem repeats again or if the product does not start again, take the product to the nearest After Sales Service Point

• WARNING: The machine must be always kept on a horizontal basis, in a safe and stable way.

• WARNING! Use a washer on a flat, leveled surface, in an upright position. Failure to do so will invalidate your warranty.

• NEVER lay the washer down during use.

• DO NOT adjust any internal control valves, as they have been factory-set.

• DO NOT connect other appliances to the machine inlet or outlet.

• DO NOT use hoses and fittings other than those designed for use with this machine.

• DO NOT touch the plug with wet hands. To avoid the risk of electrocution keep all connections dry and off the ground.

• DO NOT use a washer if you are tired or under the influence of alcohol, drugs or intoxicating medication.

• DO NOT allow children or untrained persons to operate the washer.

• WARNING! Discharge residual pressure before disconnecting the washer hose. Pressure left in the unit may cause injury.

• After use, disconnect the washer from the electrical mains and water supply and store in a safe, dry, childproof area.

• Protect from freezing conditions during winter.

• Always use the appliance at the lowest pressure setting when cleaning in the vicinity of wheels and tires.

• NOTE: This appliance is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they DO NOT play with the appliance.

INTRODUCTION

Ideal for cleaning vehicles, machinery, as well as patios and other outdoor surfaces. Quick release nozzle system allows for fast selection between fan and Rotablast® nozzle. The pressure gun includes a lock to avoid accidental start. 1200W motor produces up to 100 bar of pressure with an impressive 390L/hr flow rate. Automatic Total Stop System (TSS) which switches the motor on and off when the trigger is operated, prolonging motor life. The self- priming motor can be used with a still water source for maximum portability. Supplied with 5m pressurized hose for ease of use and 5m power cable for extended reach. Includes lance accessory suitable for snow foam and detergent.

SPECIFICATION

• MODEL NO :……………………………………………………PW1610
• Effective Cleaning Power : …………………………………….100bar
• Hose Length :……………………………………………………………5m
• IP Rating: ……………………………………………………………..IPX5
• Maximum Inlet Pressure: ………………………………………1.2bar
• Maximum Pressure: ……………………………….100bar(1450psi)
• Maximum Water Flow :…………………………………………390L/hr
• Motor Power :………………………………………………………1200W
• Nozzles: ………………………………………….Rotablast® and Fan
• Peak Water Temperature: ……………………………………….50°C
• Rated Pressure: ………………………………………70bar(1015psi)
• Rotablast Nozzle®: ……………………………………………..160bar
• Supply :…………………………………………………………………240V
• Vibration value: ……………………………………………..2.089 m/s²
• Uncertainty :………………………………………………………1.5 m/s²
• Noise Power :……………………………………………89.8 dB(A) LWA
• Noise Pressure: ………………………………………..76.9 dB(A) LPA
• Water Flow Rate: ………………………………………5.5L/6.5L/min

CONTENTS

ASSEMBLY

ATTACH THE MIDDLE EXTENSION LANCE TO WAND (FIG.1 & 2)
Note: When attaching, align the two projections on the lance with the grooves on the wand.
Attach the adjustable nozzle to the middle extension lance. Note: When attaching,align the projection on the front lance with the groove on the middle extension lance with the button held.

MOUNTING THE HANDLE (FIG.3)
Screw the handle tight to the main unit (2 screws). Note: The screws will be packed together with the manual.

FIT WHEELS (FIG.4)
Align each wheel axle with the corresponding shape on the body of the washer. Press to fit.

MOUNTING THE HIGH PRESSURE HOSE HOOK (FIG.5)
Screw the high-pressure hose hook to the main unit (2 screws). The screws will be packed together with the manual. Note: All screws are packed in one bag.

FIT GUN HOLDER AND POWER CABLE HOOK (FIG.6)

ATTACH AND DETACH THE HIGH-PRESSURE HOSE FIGS (7 & 7A)

• Attach one end of the high-pressure hose to the pressure water outlet of the machine and the other end of the high-pressure hose to the wand.
• Note: After the high-pressure hose is connected, check the connection by gently pulling on the hose to ensure it stays connected.
• Detach: To detach the hose, turn the switch to the OFF/II position and pull the trigger to drain water from the wand. Push the lock button and pull to detach the high-pressure hose.

ATTACH THE GARDEN HOSE (FIG.8)
Remove the plastic plug from the water inlet pipe of the machine and screw the water inlet connector onto the water inlet pipe. Connect one end of the garden hose (not supplied) to the water inlet connector and another end to a water source.

• WARNING! The appliance is INTENDED to be used at temperatures above 0°C.
• WARNING! The garden hose must not be damaged and leak. Inner diameter no less than 1/2”, length can not be greater than 8m. Connect to mains power.

OPERATION

WARNING! During operation appliance must be positioned on a firm, stable surface. The high-pressure hose must not be coiled on the washer.
WARNING! Check that the supply voltage and frequency correspond to those specified on the appliance data plate. The appliance should only be connected to a mains power supply via a security breaker (Max.30mA) to cut off the electricity supply in the instance of a short circuit.

START-UP (FIG.9)
Turn the water on. Squeeze trigger for approx. 1 minute until low-pressure water flows out, to empty air out of the unit.

WARNING! For use with cold water only.
Note: Before pressing the trigger, make sure the lock-off switch is in the “unlock” position. Turn the switch off the pressure wash to the “ON/I” position, then press the trigger.

WARNING! DO NOT start the machine without connecting and turning on the water supply, it may cause damage to high pressure seals and reduce the service life of the pump.

CLEANING
Squeeze the trigger, high-pressure water flow will come out.
Rotate the adjustable nozzle collar, fig.9A, to change it from a full fan spray (diagram 1) to a direct stream spray (diagram 2).

WARNING: When operating the machine, it must only be used upright.
Note: Begin with the nozzle 1-2ft away from the surface and approach with caution until it reaches the desired position. Too close a spray may do harm to the surface.

WARNING! DO NOT connect the machine to water supplies that are dirty, rusty, muddy, or corrosive: including window cleaning liquids, plant foods, or fertilizers etc.
When cleaning is finished, release the trigger and turn the switch to the “OFF/O” position, then turn off the water supply.

• Note: When not in use, make sure the Lock-off switch is in the “Lock” position.
• Note: Using the pressure washer after the water supply has been turned off, serious damage could occur to the pump and/or motor.

WARNING! Never disconnect the high-pressure discharge hose from the machine while the system is pressurized. To de-pressurize, turn the motor off, turn the water supply off, and squeeze the gun trigger 2-3 times.
Disconnect from mains supply.

SAFETY VALVE/PRESSURE LIMITING VALVE

WARNING! DO NOT tamper with or adjust the safety valve setting.

• The safety valve is also a pressure-limiting valve. When the gun trigger is released, the valve opens, the pressure switch operates, and the machine automatically shuts down. If the gun nozzle is blocked, this will cause the machine pressure to rise, the safety valve to open, the pressure switch to activate, and the machine to automatically shut down.
• Refer to section 7.2 to use a needle to clean the nozzle.

GUN SAFETY BUTTON (FIG.10)

• The operator needs to press the unlock button and then actuate the trigger to release the spray.
• When the trigger is released, the trigger will return to the off position automatically.
• When not using the pressure cleaner, press the lock button to keep from accidentally engaging the high-pressure spray.

HOLDING THE GUN
Hold the gun correctly to resist kickback force: one hand on the handle, one on the lance.

TO WASH WITH DETERGENT (FIG.11)
Fill the bottle with a recommended detergent or cleaner with a water ratio according to the instructions on the container. Connect the nozzle to the lance.

• Squeeze the wand trigger, detergent will come out through the nozzle.
• Apply detergent so it thoroughly covers the cleaning surface.
• Allow detergent to remain on the surface for a few minutes. Use a brush to lightly scrub heavily soiled areas. Change to spray nozzle, Rinse detergent from the surface.
  Cleaning up: Always draw fresh water through the detergent bottle when done to flush any remaining detergents from the injection system. The bottle could be detached if necessary.
  PLACEMENT OF ACCESSORIES ON THE MACHINE (FIG.12) Gun, power lead, hose and accessories are placed as shown below.

MAINTENANCE

WARNING! Always disconnect from the main supply before carrying out any work on the appliance.
Note: Any maintenance operations not covered by this chapter should be carried out by a properly qualified person or the manufacturer.

CLEANING OF WATER INLET FILTER (FIG.13)
The water filter installed inside the water inlet connector should be cleaned periodically. Rinse with clean tap water, and then place it back into the water inlet connector.

CLEANING THE NOZZLE (FIG.14)
Using the nozzle tip cleaner provided (or an unfolded paper clip), insert the wire into the nozzle hole and move back and forth until the debris is dislodged. Back flush water through the nozzles using a garden hose and the highest pressure available (either standard water nozzle or use your thumb over the nozzle to create water pressure for a back flush.)

CLEANING OF MACHINE VENTS
The machine should be kept clean so as to let cooling air pass freely
through the machine vents.

GREASE COUPLINGS
To ensure easy connection and that o-rings work effectively, the couplings should be greased regularly.

STORAGE

• Disconnect the water source, turn on the pressure washer for a few seconds until the remaining water flows out, then turn it off quickly. Unplug the power supply.
• Disconnect the high-pressure hose and the garden hose, and coil high-pressure hose for storage.
• Store in a frost-free area with a temperature above 0°C.

TROUBLESHOOTING

ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.

REGISTER YOUR PURCHASE HERE

WEEE REGULATIONS
Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment (WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid waste authority for recycling information.

• Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications, and component parts without prior notice.
• Important: No Liability is accepted for incorrect use of this product.
• Warranty: The guarantee is 12 months from the purchase date, proof of which is required for any claim.

Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500 sales@sealey.co.uk
www.sealey.co.uk

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>