Redmi Smart Band 2 Watch User Manual

Redmi Smart Band 2 Watch

Specifications

• Touchscreen
• Fitness Tracker
• Heart Rate Sensor
• Contact Point
• Charging Cable
• Wristband

Product Overview

Read this manual carefully before use, and retain it for future reference.

Note: Illustrations of product, accessories, and user interface in the user manual are for reference purposes only. Actual product and functions may vary due to product enhancements.

How to Install

1. Insert one end of the fitness tracker into the slot from the front of the wristband.
2. Press down on the other end with your thumb to push the fitness tracker completely into the slot.

Disassembling

Remove the band from your wrist, hold on to each end and pull on the wristband until you see a small gap between the fitness tracker and the wristband. Use your finger to pop the fitness tracker out of its slot from the front side of the wristband.

Charging

1. When using the band for the first time, connect it to the charging cable to turn it on.
2. Recharge your band immediately when the battery level is low.

Connecting with APP

1. Scan the QR code to download and install the app. Add the Redmi Smart Band 2 to the app first before you start using it.
2. Log into your Xiaomi account in the app, and follow the instructions to connect and pair the band with your phone. Once the band vibrates and a pairing request is displayed on its touchscreen, tap to complete the pairing with your phone.

Note: Make sure the Bluetooth on your phone is enabled. Hold the phone and the band close to each other during pairing.

How to Use

When the band is successfully paired with your phone, it will start tracking and analyzing your daily activities and sleeping habits. Tap the touchscreen to light it up.

View notifications: Swipe down from the top on the home screen.

Enter the function list: Swipe up from the bottom on the home screen.

Switch widget: Swipe left or right when on the home screen page.

Go back: Swipe from the left edge to the right on other pages.

Precautions

FAQ

Q: How do I install the fitness tracker into the wristband?

A: Insert one end of the fitness tracker into the slot from the front of the wristband. Press down on the other end with your thumb to push the fitness tracker completely into the slot.

Q: How do I charge the Redmi Smart Band 2?

A: When using the band for the first time, connect it to the charging cable to turn it on. Recharge your band immediately when the battery level is low.

Q: How do I connect the band with my phone?

A: Scan the QR code to download and install the app. Add the Redmi Smart Band 2 to the app first before you start using it. Log into your Xiaomi account in the app, and follow the instructions to connect and pair the band with your phone. Make sure the Bluetooth on your phone is enabled and hold the phone and the band close to each other during pairing.

Product Overview

Read this manual carefully before use, and retain it for future reference.

Note: Illustrations of product, accessories, and user interface in the user manual are for reference purposes only. Actual product and functions may vary due to product enhancements.

How to Install

1. Insert one end of the fitness tracker into the slot from the front of the wristband.
2. Press down on the other end with your thumb to push the fitness tracker completely into the slot.

Disassembling
Remove the band from your wrist, hold on to each end and pull on the wristband until you see a small gap between the fitness tracker and the wristband. Use your finger to pop the fitness tracker out of its slot from the front side of the wristband.

Charging

1. When using the band for the first time, connect it to the charging cable to turn it on.
2. Recharge your band immediately when the battery level is low.

Connecting with APP

1. Scan the QR code to download and install the app. Add the Redmi Smart Band 2 to the app first before you start using it.

Compatible with: This product only supports certain Android or iOS systems. For detailed information, please check the product page on www.mi.com .

Log into your Xiaomi account in the app, and follow the instructions to connect and pair the band with your phone. Once the band vibrates and a pairing request is displayed on its touchscreen, tap to complete the pairing with your phone.

Note: Make sure the Bluetooth on your phone is enabled. Hold the phone and the band close to each other during pairing.

How to Use

When the band is successfully paired with your phone, it will start tracking and analyzing your daily activities and sleeping habits.

Tap the touchscreen to light it up.

1. View notifications: Swipe down from the top on the home screen.
2. Enter the function list: Swipe up from the bottom on the home screen.
3. Switch widget: Swipe left or right when on the home screen page.
4. Go back: Swipe from the left edge to the right on other pages.

Precautions

• Comfortably tighten the band around your wrist about one-finger width away from your wrist bone.
• When using the band to measure your heart rate, please keep your wrist still.
• The band has a water resistance rating of 5ATM (50 meters in depth). It can be worn in the swimming pool, while swimming near the shore, or during other shallow-water activities. However, it cannot be used in hot showers, sauna, or diving. Furthermore, remember to avoid the band being directly impacted by swift currents during water sports. The water-resistant function is not permanent and may decline over time.
• The touchscreen of the band does not support underwater operations. When the band comes into contact with water, use a soft cloth to wipe away excess water from its surface before use.
• During daily use, avoid wearing the band too tightly and try to keep its contact area dry. Please clean the wristband regularly with water.
• Please stop using the product immediately and seek medical assistance if the contact area on your skin shows signs of redness or swelling.
• This band is not a medical device, any data or information provided by the band should not be used as a basis for diagnosis, treatment, and prevention of diseases.
• The lithium polymer battery in this band cannot be removed. To avoid damage to the battery or the band, do not replace the battery by yourself. There is a risk of explosion if the wrong type of battery is used. Do not dispose of used batteries with household waste. Dispose of this band and used batteries as per local laws and regulations.
• Do not disassemble, strike, crush or throw the battery into fire. Stop using the battery immediately if there is any swelling or fluid leakage. Do not expose it to sunlight, fire, or environments where the ambient temperature is extreme heat.
• When planning not to use the band for a long time, turn it off and then put it away. To avoid damage caused by the over-discharge of the battery, fully charge the band every 6 months.

Battery Safety

• This device is equipped with a built-in battery that cannot be removed or replaced. Do not disassemble or modify the battery by yourself.
• Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion.
• Leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas.
• A battery subjected to extremely low air pressure that may result in an explosion or the leakage of flammable liquid or gas.

Specifications

• Product: Smart Band
• Name: Redmi Smart Band 2
• Model: M2225B1
• Net Weight: 26.4 g (Including strap) Item
• Dimensions: 42.81 × 25.42 × 9.99 mm
• Wristband Material: TPU
• Buckle Material: PC
• Adjustable Length: 135–215 mm
• Battery Type: Lithium-ion polymer battery
• Battery Capacity: 210 mAh
• Input: 5 V 1 A
• Water Resistance: 5ATM
• Operating Temperature: 0°C to 45°C
• Bluetooth Frequency: 2402–2480 MHz
• Maximum Output: ≤ 13 dBm
• Wireless Connectivity: Bluetooth® Low Energy 5.1

For product certifications related to this band, please go to Settings > About band > Regulatory

The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Xiaomi Inc. is under license. Other trademarks and trade names are those of their respective owners.

WEEE Disposal and Recycling Information

All products bearing this symbol are waste electrical and electronic equipment which should not be mixed with unsorted household waste. Instead, you should protect human health and the environment by handing over your waste equipment to a designated collection point for the recycling of waste electrical and electronic equipment, appointed by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences to the environment and human health. Please contact the installer or local authorities for more information about the location as well as terms and conditions of such collection points.

EU Declaration of Conformity

Hereby, Xiaomi Communications Co., Ltd. declares that the radio equipment type M2225B1 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address:
http://www.mi.com/global/service/support/declaration.html

Hereby, Xiaomi Communications Co., Ltd. declares that the radio equipment type M2225B1 is in compliance with Radio Equipment Regulations 2017. The full text of the UKCA declaration of conformity is available at the following internet address: https://www.mi.com/uk/service/support/declaration.html

Warranty Notice

As a Xiaomi consumer, you benefit under certain conditions from additional warranties. Xiaomi offers specific consumer warranty benefits which are in addition to, and not instead of, any legal warranties provided by your national consumer law. The duration and conditions related to the legal warranties are provided by respective local laws. For more information about the consumer warranty benefits, please refer to Xiaomi’s official website https://www.mi.com/en/service/warranty/. Except as prohibited by laws or otherwise promised by Xiaomi, the after-sales services shall be limited to the country or region of the original purchase. Under the consumer warranty, to the fullest extent permitted by law, Xiaomi will, at its discretion, repair, replace or refund your product. Normal wear and tear, force majeure, abuse or damage caused by the user’s negligence or fault are not warranted. The contact person for the after-sale service may be any person in Xiaomi’s authorized service network, Xiaomi’s authorized distributors or the final vendor who sold the products to you. If in doubt please contact the relevant person as Xiaomi may identify. The present warranties do not apply in Hong Kong and Taiwan. Products which were not duly imported and/or were not duly manufactured by Xiaomi and/or were not duly acquired from Xiaomi or a Xiaomi’s official seller are not covered by the present warranties. As per applicable law you may benefit from warranties from the non-official retailer who sold the product. Therefore, Xiaomi invites you to contact the retailer from whom you purchased the product.

Manufactured by: Xiaomi Communications Co., Ltd. Address: #019, 9th Floor, Building 6, 33 Xi’erqi Middle Road, Haidian District, Beijing, China, 100085
For further information, please go to www.mi.com

Importer:
Beryko s.r.o.
Pod Vinicemi 931/2, 301 00 Plzeň
www.beryko.cz

References

• Beryko.cz
• Xiaomi UK | Mobile Phone | Xiaomi Official Website
• Xiaomi Global Home
• Xiaomi UK

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>