KTC M32P10 32 Inch Gaming Monitor User Guide

June 14, 2024
KTC

KTC M32P10 32 Inch Gaming Monitor

KTC-M32P10-32-Inch-Gaming-Monitor-product

Important Safety Precautions

  1. Please read all the instructians carefully before using the product.
  2. When cleaning the display, please unplug the pawer card. Please wipe the display with a soft wet cloth instead of liquid or spray cleaner. Please use LCD screen cleaner in case of a stubborn stain.
  3. Do not use accessories that are not recommended by the manufacturer, or there may be dangerous.
  4. When unplugging the power card of the display or the power adapter, please hold the power plug with your hand rather than directly pull the power cord to unplug it.
  5. Do not place the display near water, such as bathtub, washbasin, kitchen sink, or washing machine. Do not place the display on the wet ground, or near the swimming pool. Do not use fingers or hard objects to press the surface of the LCD screen.
  6. The grooves and holes on the shell or at the back and bottom of the display are designed far the ventilation and heat dissipation of the components to ensure reliable operation. So, do not put the display on the bed, sofa, carpet, or other similar surfaces to prevent the heat dissipation holes from blocking and do not place the display near or above the radiator or heater. In addition, do not place the display in an embedded device unless adequate ventilation is provided.
  7. Only the power supply type shown on the nameplate can be used far the display. Please feel free to consult the display dealer or the local power supply administration, if you have any doubts about your power supply type.
  8. For safety, the display or the power adapter uses a power cord with a three-prong plug, whose third prong can only be properly grounded when used with a properly grounded socl<et. If your socket cannot match with the plug, please contact an electrician to replace your original socket so that the plug can give full play to ensuring safety.
  9. As you may face high voltage or other dangers after removing the shell, do not repair the display by yourself. You con have it repaired by qualified maintenance personnel.
  10. Please unplug the power cord of the display or the power adapter from the socket, and contact qualified maintenance personnel for repairing the display, when following cases occur:
  11. a. The power cord or the plug is damaged or worn out.
  12. b. The display has been dropped from high or the shell is damaged.
  13. c. Any obvious abnormality indicates a necessary repair.
  14. Please place the display in a well-ventilated environment, which is away from strong light, high temperature, or humidity.
  15. The room temperature for the display store is -1D’C-6D’C, or it may be permanently damaged.

Product Introduction

Overview
It is a kind af high-performance intelligent multiple frequency scanning display, which adopts active matrix thin film transistor LED-backlit LCD and is controlled through the microcomputer MCU digital technology. It is compact and lightweight, which is suitable for narrow working spaces.

Packing List
Before installation, check whether the fallowing articles are complete in the packing box:

  • Oisplayxl
  • Standxl
  • Basex1
  • Power Cordxl
  • Power Adapterxl
  • OP Signal Cablexl
  • User Guidexl
  • Type-C Cablexl
  • H□MI Cablexl
  • Warranty Cardxl
  • Color Correction Reportxl

If any of above product is missing, please contact with product distributor immediately.
NOTICE: Specific accessories in order to prevail in kind. Please keep packing materials far future movement.

lnstallation and Connection

Display Installation

Installation Guide

  • The display should be installed near on AC power socket that can be easily pluggable.
  • For safety purpose, it is recommended to use suitable wall mount br□cl<ets or □ base.
  • To prevent injury, the display should be placed on □ smooth horizontal plane, or fixed on a firm wall.
  • If you need to install it on a wall, it should be done by professional technicians. The improper display installation may cause instability.
  • Do not place the display where it may be suffered from mechanical vibration.
  • Do not place the display where insects may enter.
  • Do not place the display directly facing on air conditioner, □r the internal panel may condense, leading to faults.
  • Do not place the display where there is □ strong electromagnetic field, or it will be interfered with and damaged by the electromagnetic waves.KTC-M32P10-32-Inch-Gaming-Monitor-fig-1

Signal Cable Cannectian
Connect the signal coble to the HDMI or DP signal output port on the PC, then connect the other end of the signal coble to the corresponding signal input port on the LCD.

Headset Connection
After connecting to the headset, there will be audio output, and it also supports external loudspeakers.

USB Connection
Use the USB 3.0 Type-B coble to connect the USB uplink port on display with the USB port an the case, ar use the Type-C coble ta connect the Type-C port on display with the USB port on the case. Switch o port corresponding to KVM through the joystick to enable the USB port on display to transmit data.

KTC-M32P10-32-Inch-Gaming-Monitor-fig-2

Display Operation

The joystick is shown os in the figure. For the models of the same series, only the key positions and the frame styles are different. Please refer to the actual situation for details.

KTC-M32P10-32-Inch-Gaming-Monitor-fig-3

KTC-M32P10-32-Inch-Gaming-Monitor-fig-4

Power Indicator
The blue indicator represents the proper functioning of the display; the red flash indicator represents no signal state. Under the energy conservation state, the display will normally work if the signal is provided again. The display is still powered on in the standby state. Thus, unplug the power cord when you do not use the display for safety.

Key Function Introduction

Initial Status:


Joysticl < Upward

| ****

Shortcut Menu for Signal Source

---|---


Joysticl < **Downward**

| ****

Shortcut Menu for Brightness adjustment


Joystick Leftward

| ****

Shortcut Menu for Gaming Assistance


Joystick Rightward

| ****

KVM


Press Joystick

| Turn on the display/Show the menu by short-pressing, turn off the display by pressing and holding for 3 seconds

Enter the Function Menu:


Joysticl < Upward

| ****

Move upward/Adjust the value of the selected item

---|---


Joystick Downward

| ****

Move downward/Adjust the value of the selected item


Joystick Leftward

| ****

Return the previous menu


Joystick Rightward

| ****

Open/DK


Press Joysticl <

| ****

Turn off the display by pressing and holding for 3 seconds

Safety Protection
When the PC video signal exceeds the frequency range of the display, the display will disable the line and field synchronizing signals to protect the display. Under this circumstance, you must set the output frequency of the PC to an acceptable range for the display to work properly.

Simple Problems Disposal

|
---|---


1.Blank screen /Power indicator does not work

| Check whether the power supply is in goad contact with the display and the power socket; and check whether the display is turned off.


2.Dark screen

| Enter the “Brightness & Contrast” menu to regulate the contrast and the brightness of the display.


3.Display overheating

| Leave at least 5cm of ventilated space around the display. Do not place articles on the display.



4.Dark/light spats when powered an

| It is normal. Because of the temperature difference in the environment, the backlit tube emits uneven light at the initial stage after the display turns on. However, the backlit tube will emit normal light after 20 minutes, and the dark/light spots will be eliminated at that time.


5.lmage distortion, flashing, shaking

| Check your computer configuration, choose the correct resolution, and reset your refresh rate.


6.Noisy signal when powered off

| During the power-off of the display, there may be some noisy signals on the screen caused by the normal discharge.

Product Technical Specifications

Panel Dimension 31.5″
Best Operating Resolution Ratio 3840×2160 @ 144Hz
Input Voltage DC 24V / 10A
Contrast 1000:1(SDRJ,1000000:1(HOR)
Visible Area 697.306mmx392.234mm
Pitch size far wall mount 10Dmmx10Dmm
Requirements of Operating Environment
Barometric Pressure B6kpa-104kpa
Working Temperature and Humidity OC-40C
Storage Temperature and Humidity -10C-6DC
Packing Dimension (WxHxOJ and Weight
Display Dimension (WxHxOJ (excluding base) 719x421x70.9mm
Packing Dimension (WxHxOJ 98Dx56Dx235mm
Net Weight of Display (including base) 9.0Kg
Packing Weight 14.8Kg

Power Management System

|
---|---

Normal Operation

|

:s240W

Standby| <0.5W

Remark: All technical specifications in the User Guide and on the external packing are allowed to change without prior notice. If there is a subtle difference between the User Guide and the actual operation, the latter shall prevail

Instruction for base installation

KTC-M32P10-32-Inch-Gaming-Monitor-fig-5

Indicative Description of The Regulations for the Administration of the Recovery and Disposal of Waste Electrical and Electronic Products
To core for and protect the earth better, please send it to o local manufacturer with notionally recognized qualification for recycling according to the notional applicable laws and regulations an recycling of waste electrical and electronic products when you no longer need this product or at the end of its service life.
The environment-friendly use period of this product is 10 years (see the Marking for the Restriction of the Use of Hazardous Substances in the right figure).
such use period will be maintained, only if you use the product under the normal worl<ing conditions specified in the User Guide only.

Any questions or comments, please contact us as below﹕support@ktcplay.com [North America] support.eu@ktcplay.com [Europe] For your warranty information, please visit www.ktcplay.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals