QIACHIP ZBBridge-01 Smart Zigbee Bridge Hub User Manual
- June 14, 2024
- QIACHIP
Table of Contents
ZBBridge-01
User manual V1.0
ZigBee Bridge
Specifications
| Model | ZBBridge-01 |
|---|---|
| Input | 5V⎓1A |
| Wireless connections | IEEE 802.11 b/g/n 2.4GHz , ZigBee 3.0 |
| Operating systems | Android 4.1 & iOS 9.0 or higher |
| Working temperature | -10°C~40°C |
| Material | PC |
| Dimension | 76×61 x20mm |
Features
This is a ZigBee Bridge that allows you to control a variety of ZigBee devices by transforming WiFi into ZigBee. You can remotely turn on/ off or schedule on/off connected ZigBee devices, or share it with your family to control them together.
Product Introduction
- ZigBee LED indicator(Green)
- WiFi LED indicator(Blue)
- Input
- Pairing button
Operating Instruction
(1) Download APP
(2) Power on
After powering on, the device will enter the quick pairing mode (Touch) during the first use. The WiFi LED indicator changes in a cycle of two short and one long flash.
The device will exit the quick pairing mode (Touch) if not paired with in 3mins.lf you want to enter this mode, please long press the pairing button for about 5s until the WiFi LED indicator changes in a cycle of two short and one long flash and release.
(3) Add ZigBee Bridge
Connect your phone to 2.4GHz WiFi and turn on Bluetooth. Tab”+” and select “Bluetooth Pairing”, then operate following the prompt on the APP.
(4) Add a ZigBee sub-device ZigBee Bridge
Set it to the pairing mode before adding the ZigBee sub-device. then tap “+” pair the device with the ZigBee sub-device.
ZigBee Bridge can add up to 32 sub-devices now. It will support adding more sub-devices soon.
LED indicator status instruction
| Blue LED flashes (one long and two short | Quick Pairing Mode |
|---|---|
| Blue LED flashes quickly | Compatible Pairing Mode (AP) |
| Blue LED keeps on | Device is connected successfully |
| Blue LED flashes quickly once | Unable to discover the router |
| Blue LED flashes quickly twice | Connect to the router but fail to connect to |
WiFi
Blue LED flashes quickly three times| Upgrading
Green LED flashes twice| Sub-device deleting prompt
Green LED flashes slowly| Searching and adding
Compatible Pairing Mode(AP)
If you fail to enter Quick Pairing Mode (Touch), please try “Compatible Pairing Mode (AP)” to pair.
(1) Long press pairing button for 5s until the WiFi LED indicator changes in a cycle of two short flashes and one long flash and release. Long press pairing button for 5s again until the WIFi LED indicator flashes quickly, then the device enters Compatible Pairing Mode (AP).
(2) Tap”+” and select “Compatible Pairing Mode (AP)” on APP
For Android system: Enter WiFi password and tap “Next”. Be patient until
pairing completes.
For iOS system: Select WiFi SSID with ITEAD-****” and enter the password
12345678,and then go back to eWeLink APP and tap “Next”. Be patient until
pairing completes.
Delete ZigBee sub-devices
Long press the pairing button for 10s until the ZigBee LED indicator “flashes twice” that all paired sub-devices will be deleted successfully.
Delete single sub-device on APP
Factory Reset
Long press the pairing button for about 5s until the WiFi LED indicator changes in a cycle of two short and one long flash and release, then the reset is successful. The device enters quick pairing mode(Touch).
Image
Please reset the device to factory defaults if you want to change the WiFi network, then reconnect the new network.
Common Problems
Tap “ ” on eWeLink APP and select “FAQ ” to check.
eWeLink has integrated with mainstream Al platforms:
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>