BOSCH GSR 18V-90 C Professional Cordless Drill Instruction Manual

GSR/GSB 18V-85 C Professional Cordless Drill
Instruction Manual

Safety Instructions

General Power Tool Safety Warnings
WARNING
Read all safety warnings, instructions, illustrations, and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire, and/or serious injury.

Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.

Work area safety

• Keep work area clean and well-lit. Cluttered or dark areas invite accidents.
• Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or Power tools create sparks that may ignite the dust or fumes.
• Keep children and bystanders away while operating a
  power tool. Distractions can cause you to lose

Electrical safety

• Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce the risk of electric shock.

• Avoid body contact with earthed or grounded sur­ faces, such as pipes, radiators, ranges, and refrigerat­ There is an increased risk of electric shock if your body is earthed or grounded.

• Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of elec­tric shock.

• Do not abuse the cord. Never use the cord for carry­ ing, pulling, or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric

• When operating a power tool outdoors, use an exten­ sion cord suitable for outdoor use. The use  of a cord suit­able for outdoor use reduces the risk of electric shock.

• If operating a power tool in a damp location is un­avoidable, tse a residual current device (RCD) protec­ ted supply. Use of an RCD reduces the risk of electric

Personal safety

• Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inatten­tion while operating power tools may result in serious per­sonal injury.
• Use personal protective equipment. Always wear eye Protective equipment such as a dust mask, non-skid safety shoes, hard hat or hearing protection used for appropriate conditions will reduce personal in­juries.
• Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or en­ergising power tools that have the switch on invites acci­
• Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal in­
• Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
• Dress properly. Do not wear loose clothing or jew­ Keep your hair and clothing away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
• If devices are provided for the connection of dust ex­ traction and collection facilities, ensure these are con­ nected and properly used. Use of dust collection can re­duce dust-related hazards.
• Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool safety principles. A careless action can cause severe in­jury within a fraction of a second.

Power tool use and care

• Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was de­
• Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
• Disconnect the plug from the power source and/or re­ move the battery pack, if detachable, from the power tool before making any adjustments, changing ac­ cessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool
• Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
• Maintain power tools and accessories. Check for mis­ alignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
• Keep cutting tools sharp and clean. Properly main­tained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
• Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into ac­ count the working conditions and the work to be per­ Use of the power tool for operations different from those intended could result in a hazardous situation.
• Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.

Battery tool use and care

• Recharge only with the charger specified by the manu­facturer. A charger that is suitable for one type of bat­tery pack may create a risk of fire when used with another battery pack.
• Use power tools only with specifically designated bat­ tery packs. Use of any other battery packs may create a risk of injury and fire.
• When the battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws, or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or afire.
• Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally oc­ curs, flush with water. If liquid contacts eyes, addi­ tionally seek medical help. Liquid ejected from the bat­tery may cause irritation or burns.
• Do not use a battery pack or tool that is damaged or Damaged or modified batteries may exhibit unpredictable behavior resulting in fire, explosion, or risk of injury.
• Do not expose a battery pack or tool to fire or excess­ ive temperature. Exposure to fire or temperature above 130°C may cause an explosion.
• Follow all charging instructions and do not charge the battery pack or tool outside the temperature range specified in the instructions. Charging improperly or at temperatures outside the specified range may damage the battery and increase the risk of fire.

Service

• Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.
• Never service damaged battery packs. Service of bat­tery packs should only be performed by the manufacturer or authorized service providers.

Safety information for drills and screwdrivers
Safety instructions for all operations

• Wear ear protectors when impact drilling. Exposure to noise can cause hearing loss.
• Use the auxiliary handle(s). Loss of control can cause personal injury.
• Hold the power tool by insulated gripping surfaces, when performing an operation where the cutting ac­ cessory or fasteners may contact hidden wiring. Cut­ting accessory or fasteners contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.

Safety instructions when using long drill bits

• Never operate at higher speed than the maximum speed rating of the drill bit. At higher speeds, the bit is likely to bend if allowed to rotate freely without contact­ing the workpiece, resulting in personal injury.
• Always start drilling at low speed and with the bit tip in contact with the workpiece. At higher speeds, the bit is likely to bend if allowed to rotate freely without contact­ing the workpiece, resulting in personal injury.
• Apply pressure only in direct line with the bit and do not apply excessive pressure.Bits can bend causing breakage or loss of control, resulting in personal injury.

Additional safety warnings

• Hold the power tool securely. When tightening and loosening screws be prepared for temporarily high torque

• Secure the workpiece. A workpiece clamped with clamping devices or in a vice is held more secure than by

• Use suitable detectors to determine if there are hid­ den supply lines or contact the local utility company for assistance. Contact with electric cables can cause fire and electric shock. Damaging gas lines can lead to ex­ Breaking water pipes causes property damage.

• Always wait until the power tool has come to a com­ plete stop before placing it down. The application tool can jam and cause you to lose control of the power tool.

• In case of damage and improper use of the battery, va­ pours may be emitted. The battery can set alight or ex­ Ensure the area is well ventilated and seek medical attention should you experience any adverse effects. The vapours may irritate the respiratory system.

• Do not open the battery. There is a risk of short-circuit­

• The battery can be damaged by pointed objects such as nails or screwdrivers or by force applied externally. An internal short circuit may occur. causing the battery to burn. smoke. explode or overheat.

• Only use the battery with products from the manufac­. This is the only way in which you can protect the battery against dangerous overload.
  Protect the battery against heat, e.g. against continuous intense sunlight, fire, dirt, water, and moisture. There is a risk of explosion and short- circuiting.

• Switch the power tool off immediately if the applica­tion tool becomes blocked. Be prepared for high torque reactions which cause kickback. The applica­tion tool becomes blocked when it becomes jammed in the workpiece or when the power tool becomes over­

• Caution! When using the power tool with Bluetooth . a fault may occur in other devices and systems, aero­planes and medical devices (e.g. pacemakers, hearing aids). Also, damage to people and animals in the im­mediate vicinity cannot be completely excluded. Do not use the power tool with Bluetooth in the vicinity of medical devices, petrol stations, chemical plants, areas with a potentially explosive atmosphere or in blasting areas. Do not use the power tool with Bluetooth in aircraft. Avoid using the product near your body for extended periods.

The Bluetooth® word mark and logos are registered trade­marks owned by Bluetooth SIG, Inc. and any use of such marks by Robert Bosch Power Tools GmbH is under li­cense.

Product Description and Specifications

Read all the safety and general instructions.
Failure to observe the safety and general instructions may result in electric shock, fire, and/or serious injury. Please observe the illustrations at the beginning of this operating manual.

Intended use
The power tool is intended for driving and loosening screws and for drilling in wood, metal, ceramic, and plastic. The GSB is also designed for impact drilling in brick, masonry, and stone.
With the Bluetooth® Low Energy Module GCY 42 inserted, power tool data and settings can be transferred between the power tool and a mobile device by means of Bluetooth® wireless technology.

Product features
The numbering of the product features refers to the diagram of the power tool on the graphics page.

indicator
(5) Intermediate piece of auxiliary handle| (15) Universal bit holdera)
(6) Wing bolt for depth stop adjustment| (16) Rotational direction switch
(7) Torque presetting ring| (17) On/off switch
(8) Mode selector switch| (18) Handle (insulated gripping surface)
(9) Gear selector switch| (19) Bluetooth® Low Energy Module cover GCY 42
(10) Belt clip|

a) Accessories shown or described are not included with the product as standard. You can find the complete selection of accessories in our accessories range.

Technical data

ProCORE18V…
Recommended chargers| | GAL 18…
GAX 18…
GAL 36…| GAL 18…
GAX 18…
GAL 36…

A) Measured at 20−25 °C with rechargeable battery GBA 18V 4.0Ah.
B) Measured with GBA 18V 1.5Ah and GBA 18V 12Ah.

Noise/Vibration Information

| GSR 18V-85 C| GSB 18V-85 C
---|---|---
Noise emission values were determined according to EN 62841-2-1. Typically, the A-weighted noise level of the power tool is
Sound pressure level
Sound power level| dB(A)
dB(A)| 87
98| 87
98
Uncertainty K| dB| 5| 5
Wear hearing protection!
Vibration total values ah (triax vector sum) and uncertainty K determined according to EN 62841-2-1:
Drilling:
ah K| m/s2
m/s’| <2.5
1.5| <2.5
1.5
Impact drilling|
ah K| ni/s2
m/s2| –
–| 15.5
1.5

The vibration level and noise emission value given in these instructions have been measured in accordance with a standardized measuring procedure and may be used to compare power tools. They may also be used for a preliminary estimation of vibration and noise emissions. The stated vibration level and noise emission value represent the main applications of the power tool. However, if the power tool is used for other applications, with different application tools or is  poorly maintained, the vibration level and noise emission value may differ. This may significantly increase the vibration and noise emissions over the total working period.
To estimate vibration and noise emissions accurately, the times when the tool is switched off or when it is running but not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions over the total working period.
Implement additional safety measures to protect the operator from the effects of vibration, such as servicing the power tool and application tools, keeping their hands warm, and organizing workflows correctly.

Assembly

• Remove the battery from the power tool before carrying out work on the power tool (e.g. maintenance, changing tool, etc.). The battery should also be removed for transport and storage. There is risk of injury from unintentionally pressing the on/off switch.

Inserting the Bluetooth® Low Energy Module GCY 42 (Accessory)
Read the corresponding operating instructions for information about the Bluetooth® Low Energy Module GCY 42.
Charging the Battery

• Use only the chargers listed in the technical data. Only these chargers are matched to the lithium-ion battery of your power tool.

Note: The battery is supplied partially charged. To ensure full battery capacity, fully charge the battery in the charger before using your power tool for the first time.

The lithium-ion battery can be charged at any time without reducing its service life. Interrupting the charging process does not damage the battery.
The lithium-ion battery is protected against deep discharge by the “Electronic Cell Protection (ECP)”. When the battery is discharged, the power tool is switched off by means of a protective circuit: The application tool no longer rotates.

• Do not continue to press the On/Off switch after the power tool has automatically switched off. The battery can be damaged.

Follow the instructions on correct disposal.
Removing the Battery
The battery (11) is equipped with two locking levels to prevent the battery from falling out when pushing the battery release button (12) unintentionally. As long  as the battery is inserted in the power tool, it is held in position by means of a spring.
To remove the battery (11), press the release button (12) and pull the battery out of the power tool. Do not use force to do this.

Battery charge indicator
The green LEDs on the battery charge indicator indicate the state of charge of the battery. For safety reasons, it is only possible to check the state of charge  when the power tool is not in operation. Press the button for the battery charge indicator or to show the state of charge. This is also possible when the battery  is removed. If no LED lights up after pressing the button for the battery charge indicator, then the battery is defective and must be replaced.

**Battery model GBA 18V…

**

**Battery model ProCORE18V…

**

Auxiliary handle

• Do not operate your power tool without the auxiliary handle (4).
• Before carrying out any work, make sure that the auxiliary handle is tightened. Loss of control can cause personal injury. Ensure that the auxiliary handle is tightened with a torque suited to the fastening method; fasten this to the power tool so that any movement of the auxiliary handle around or along the drilling axis is avoided.

Fitting the auxiliary handle
To open the auxiliary handle, turn the lower gripping end of the auxiliary handle (4) in an anticlockwise direction.
Pull back the intermediate piece of the auxiliary handle (5) and hold it in this position.
Slide the auxiliary handle over the drill chuck to mount the auxiliary handle on the power tool.
Then let go of the intermediate piece (5).
Afterward, turn the lower gripping end of the auxiliary handle (4) clockwise to retighten it.

Swivelling the auxiliary handle
You can swivel the auxiliary handle (4) to any angle for a safe work posture that minimizes fatigue.
Turn the lower gripping end of the auxiliary handle (4) anticlockwise and swivel the auxiliary handle (4) into the required position. Afterward, turn the lower gripping end of the auxiliary handle (4) clockwise to retighten it.

Setting the drilling depth
You can use the depth stop (3) to set the required drilling depth X.
Loosen the wing bolt for adjusting the depth stop (6) and insert the depth stop into the auxiliary handle (4).
Pull the depth stop (3) far enough out that the distance between the drill bit tip and the edge of the depth stop (3) corresponds to the required drilling depth X.
Retighten the wing bolt for adjusting the depth stop (6).

Changing the tool (see figure A)

• Remove the battery from the power tool before carrying out work on the power tool (e.g. maintenance, changing tool, etc.). The battery should also be removed for transport and storage. There is risk of injury from unintentionally pressing the on/off switch.

The drill spindle is locked when the on/off switch (17) is not pressed. This makes it possible to change the application tool in the drill chuck quickly, conveniently and easily. Open the keyless chuck (2) by turning it in the direction of rotation ➊ until the tool can be inserted. Insert the tool.
Firmly tighten the keyless chuck (2) by turning it by hand in the direction of rotation ➋. This will automatically lock the drill chuck.

Dust/Chip Extraction
Dust from materials such as lead-containing coatings, some wood types, minerals and metal can be harmful to one’s health. Touching or breathing-in the dust  can cause allergic reactions and/or lead to respiratory infections of the user or bystanders.
Certain dust, such as oak or beech dust, is considered carcinogenic, especially in connection with wood-treatment additives (chromate, wood preservative).  Materials containing asbestos may only be worked by specialists.

• Provide for good ventilation of the working place.
• It is recommended to wear a P2 filter-class respirator.

Observe the relevant regulations in your country for the materials to be worked.

• Avoid dust accumulation at the workplace. Dust can easily ignite.

Operation

Starting Operation
Inserting the battery
Note: The use of batteries unsuitable for your power tool can lead to malfunctions or damage to the power tool.
Set the rotational direction switch (16) to the middle position to avoid unintentionally switching it on. Insert the charged battery (11) into the handle until you feel it engage and it is flush with the handle.
Setting the Rotational Direction (see figure B)
The rotational direction switch (16) is used to change the rotational direction of the power tool. However, this is not possible while the on/off switch (17) is being pressed.
Right rotation: To drill and to drive in screws, press the rotational direction switch (16) through to the right stop.
Left rotation: To loosen and unscrew screws and nuts, press the rotational direction switch (16) through to the left stop.

Setting the operating mode

| Drilling
Set the mode selector switch (8) to the “drilling” symbol.
---|---
| Screwdriving
Set the mode selector switch (8) to the “screwdriving” symbol.
| Impact drilling (GSB 18V-85 C)
Set the mode selector switch (8) to the “impact drilling” symbol.

Switching on/off
To start the power tool, press and hold the on/off switch (17).
The LED (13) lights up when the on/off switch (17) is lightly or fully pressed, meaning that the work area is illuminated in poor lighting conditions.
To switch off the power tool, release the on/off switch (17).

Adjusting the Speed
You can adjust the speed of the power tool when it is on by pressing in the on/off switch (17) to varying extents.
Light pressure on the on/off switch (17) results in a low rotational speed. Increased pressure on the switch causes an increase in speed.

Preselecting torque (applies to screwdriving mode)
The torque presetting ring (7) can be used to preselect the required torque in 25 stages. Once the set torque has been reached, the application tool will be stopped.

Mechanical gear selection

• Only operate the gear selector (9) when the power tool is not in use.

First gear:
Low-speed range; for working with a large drilling diameter or for screwdriving.

Second gear:
High-speed range; for working with a small drilling diameter.

• Always push the gear selector switch as far as it will go. Otherwise, the power tool may become damaged.

Temperature-dependent overload protection
When used as intended, the power tool cannot be overloaded. In the event of overloading or the temperature rising/falling outside the permitted operating temperature range, the speed will be reduced. The power tool will not run at full speed again until the permitted operating temperature has been reached.
Activation of the temperature-controlled overload protector is indicated by the LED (14) on the power tool lighting up red. To return to within the permitted operating temperature range, switch the gear selector (9) to first gear, run the power tool at no load or wait until the LED (14) goes out.
When the LED (14) has gone out, the tool has returned to within the permitted operating temperature range.

Protection against deep discharge
The lithium-ion battery is protected against deep discharge by the “Electronic Cell Protection (ECP)”. When the battery is discharged, the power tool is switched off by means of a protective circuit: The application tool no longer rotates.

Emergency switch-off (KickBack Control)
The rapid shut-off function (KickBack Control) gives the user greater control over the power tool and offers them better protection than power tools that do not have KickBack Control. The power tool will switch off if it suddenly and unforeseeably rotates around the drilling axis.

Rapid shut-off is indicated by the LED on the power tool flashing.
To switch the tool back on , release the on/off switch and then press it again.

• It will no longer be possible to switch the power tool on if the KickBack Control function is faulty. Has the power tool serviced by a qualified repair person using only original replacement parts?

Connectivity functions
In conjunction with the Bluetooth® Low Energy Module GCY 42, the following connectivity functions are available for the power tool:

• Registration and personalization
• Status check, the output of warning messages
• General information
• Management

Read the corresponding operating instructions for information about the Bluetooth® Low Energy Module GCY 42.

Practical advice

• The power tool with inserted Bluetooth® Low Energy
  Module GCY 42 is equipped with a radio interface.
  Local operating restrictions, e.g. in aircraft or hospitals, must be observed.

• Only apply the power tool to the screw when the tool is switched off. Rotating application tools can slip off.

An auxiliary tool can be used to remove the screwdriver bit or universal bit holder.

Belt clip
You can use the belt clip (10) to hang the power tool on a belt, for example. You then have both hands free and the power tool is always at hand.

Maintenance and Service

Maintenance and Cleaning

• Remove the battery from the power tool before carrying out work on the power tool (e.g. maintenance, changing tool, etc.). The battery should also be removed for transport and storage. There is a risk of injury from unintentionally pressing the on/off switch.
• To ensure safe and efficient operation, always keep the power tool and the ventilation slots clean.

After-Sales Service and Application Service
Our after-sales service responds to your questions concerning maintenance and repair of your product as well as spare parts. You can find explosion drawings and information on spare parts at: www.bosch-pt.com
The Bosch product use advice team will be happy to help you with any questions about our products and their accessories.
In all correspondence and spare parts orders, please always include the 10‑digit article number given on the nameplate of the product.

Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange the collection of a product in need of servicing or repair.
Tel. Service: (0344) 7360109
E-Mail: boschservicecentre@bosch.com
You can find further service addresses at:
www.bosch-pt.com/serviceaddresses

Transport
The contained lithium-ion batteries are subject to the Dangerous Goods Legislation requirements. The batteries are suitable for road transport by the user without further restrictions.
When shipping by third parties (e.g.: by air transport or forwarding agency), special requirements on packaging and labeling must be observed. For the preparation of the item being shipped, consulting an expert for hazardous material is required.
Dispatch battery packs only when the housing is undamaged. Tape or mask off open contacts and pack up the battery in such a manner that it cannot move around in the packaging. Please also observe the possibility of more detailed national regulations.

Disposal
Power tools, rechargeable batteries, accessories, and packaging should be sorted for environmental-friendly recycling.
Do not dispose of power tools and batteries/rechargeable batteries into household waste!

Only for EU countries:
According to the Directive 2012/19/EU, power tools that are no longer usable, and according to the Directive
2006/66/EC, defective or used battery packs/batteries, must be collected separately and disposed of in an environmentally correct manner.

Only for the United Kingdom:
According to Waste Electrical and Electronic Equipment Regulations, 2013 (2013/3113) and the Waste Batteries and Accumulators Regulations 2009 (2009/890), power tools that are no longer usable must be collected separately and disposed of in an environmentally friendly manner.

Battery packs/batteries: Li-ion:
Please observe the notes in the section on transport (see “Transport”, page 20).

Licenses
Copyright © 2009–2020 ARM LIMITED
All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are
met:

• Redistributions of source code must retain the above copyright notice, this list of conditions, and the following disclaimer.
• Redistributions in binary form must reproduce the above copyright notice, this list of conditions, and the following disclaimer in the documentation and/or other materials provided with the distribution.
• Neither the name of ARM nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.

THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY  DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR  OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

Copyright © 2012–2019 STMicroelectronics
All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are
met:

• Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
• Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
• Neither the name of STMicroelectronics nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.

THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY  DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR  OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

EU Declaration of Conformity| We declare under our sole responsibility that the stated products comply with all applicable provisions of the directives and regulations listed below and are in conformity with the following standards. Technical file at: *
---|---
Cordless drill/driver
Article number

Robert Bosch Power Tools GmbH
70538 Stuttgart
GERMANY
www.bosch-pt.com
1 609 92A 5TY (2021.09) O / 260

1 609 92A 5TY

References

• Invented for life | Bosch Global
• The domain name bosch.mk is for sale
• Početna strana | Bosch u Srbiji
• Roundcube Webmail :: Welcome to Roundcube Webmail
• 巧米网为您服务！(QiaoMi.com)
• Skånevik Ølen Kraftlag AS
• Електроінструменти Bosch | Bosch Professional
• bosch-professional.com/wac
• Электроинструменты Bosch | Bosch Professional
• Bosch Power Tools | Bosch Power Tools
• Location selection | Bosch Power Tools
• Електроинструменти на Bosch | Електроинструменти на Bosch
• Service worldwide
• Elektrické nářadí Bosch | Elektrické nářadí Bosch
• Bosch Elektrowerkzeuge und Zubehör | Bosch Elektrowerkzeuge
• Bosch el-værktøj | Bosch el-værktøj
• Bosch-sähkötyökalut | Bosch-sähkötyökalut
• Outillage électroportatif Bosch | Outillage électroportatif Bosch
• Ηλεκτρικά εργαλεία Bosch | Ηλεκτρικά εργαλεία Bosch
• Bosch elektromos kéziszerszámok | Bosch elektromos kéziszerszámok
• Elektronarzędzia Bosch | Elektronarzędzia Bosch
• Scule electrice Bosch | Scule electrice Bosch
• Bosch električni alati | Bosch električni alati
• Bosch Услуги | Электроинструменты Bosch
• Elektrické náradie Bosch | Elektrické náradie Bosch
• Invented for life | Bosch Global
• Ana Sayfa | Bosch Türkiye
• Početna | Bosch u Hrvatskoj
• herramientasbosch.net
• Open Source Initiative – The steward of the Open Source Definition, setting the foundation for the Open Source Software ecosystem.
• bosch-professional.com/wac/

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>