BOSCH GSB Professional Impact Drill Instruction Manual

GSB Professional
Original instructions

GSB Professional Impact Drill

Safety Instructions

General Power Tool Safety Warnings

WARNING

Read all safety warnings, instructions, illustrations and specifica- tions provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/ or seriousinjury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mainsoperated (corded) power tool or battery-operated (cordless) power tool.

Work area safety

• Keep work area clean and well lit. Cluttered or dark areas invite accidents.
• Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
• Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.

Electrical safety

• Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.

• Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators.
  There is an increased risk of electric shock if your body is earthed or grounded.

• Do not expose power tools to rain or wet conditions.
  Water entering a power tool will increase the risk of electric shock.

• Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts.
  Damaged or entangled cords increase the risk of electric shock.

• When operating a power tool outdoors, use an extension cord suitable for outdoor use.
  Use of a cord suitable for outdoor use reduces the risk of electric shock.
  u If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply.
  Use of an RCD reduces the risk of electric shock.

Personal safety

• Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inatten- tion while operating power tools may result in serious personal injury.

• Use personal protective equipment. Always wear eye protection. Protective equipment such as a dust mask, non-skid safety shoes, hard hat or hearing protection used for appropriate conditions will reduce personal injuries.

• Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool.
  Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents.

• Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.

• Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.

• Dress properly. Do not wear loose clothing or jewellery. Keep your hair and clothing away from moving parts.
  Loose clothes, jewellery or long hair can be caught in moving parts.

• If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used.
  Use of dust collection can reduce dust-related hazards.

• Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool safety principles. A careless action can cause severe injury within a fraction of a second.

Power tool use and care

• Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.

• Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.

• Disconnect the plug from the power source and/or remove the battery pack, if detachable, from the power
  tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.

• Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.

• Maintain power tools and accessories. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.

• Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.

• Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed.
  Use of the power tool for operations different from those intended could result in a hazardous situation.

• Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.

Service

• Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.

Safety Warnings for Drills

Safety instructions for all operations

• Wear ear protectors when impact drilling. Exposure to noise can cause hearing loss.
• Use the auxiliary handle(s). Loss of control can cause personal injury.
• Hold the power tool by insulated gripping surfaces, when performing an operation where the cutting accessory or fasteners may contact hidden wiring or its own cord.
  Cutting accessory or fasteners contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.

Safety instructions when using long drill bits

• Never operate at higher speed than the maximum speed rating of the drill bit. At higher speeds, the bit is likely to bend if allowed to rotate freely without contacting the workpiece, resulting in personal injury.
• Always start drilling at low speed and with the bit tip in contact with the workpiece. At higher speeds, the bit is likely to bend if allowed to rotate freely without contacting the workpiece, resulting in personal injury.
• Apply pressure only in direct line with the bit and do not apply excessive pressure.Bits can bend causing breakage or loss of control, resulting in personal injury.

Additional safety warnings

• Switch the power tool off immediately if the application tool becomes blocked.
  Be prepared for high torque reactions which cause kickback. The application tool becomes blocked when it becomes jammed in the workpiece or when the power tool becomes overloaded.

• Hold the power tool securely. When tightening and loosening screws be prepared for temporarily high torque reactions.

• Secure the workpiece. A workpiece clamped with clamping devices or in a vice is held more secure than by hand.

• Use suitable detectors to determine if utility lines are hidden in the work area or call the local utility company for assistance. Contact with electric lines can lead to fire and electric shock. Damaging a gas line can lead to explosion. Penetrating a water line causes property damage or may cause an electric shock.

• Always wait until the power tool has come to a complete stop before placing it down. The application tool can jam and cause you to lose control of the power tool.

Product Description and Specifications

Read all the safety and general instructions.
Failure to observe the safety and general instructions may result in electric shock, fire and/or serious injury.
Please observe the illustrations at the beginning of this operating manual.

Intended Use
The power tool is intended for impact drilling in brick, concrete and stone, as well as for drilling in wood, metal, ceramic and plastic. Tools with electronic control and right/ left rotation are also suitable for screwdriving and thread cutting.

Product Features

The numbering of the product features refers to the diagram of the power tool on the graphics page.

1. Keyless chuck
2. Front sleeve
3. Rear sleeve
4. “Drilling/impact drilling” selector switch
5. Lock-on button for on/off switch
6. On/off switch
7. Speed preselection thumbwheel (GSB 16 RE)
8. Rotational direction switch (GSB 10 RE/GSB 13 RE/ GSB 16 RE/GSB 1000 RE)
9. Button for depth stop adjustment a)
10.  Wing bolt for attaching the auxiliary handle a)
11. Auxiliary handle (insulated gripping surface) a)
12. Depth stopa)
13.  Handle (insulated gripping surface)
14. Chuck key a)
15.  Keyed chucka)
16. Universal bit holder a)
17. Screwdriver bit a)b)
18. Hex key a)b)
19. Open-ended spanner a)b)
    a) Accessories shown or described are not included with the product as standard. You can find the complete selection of accessories in our accessories range.
    b) Commercially available (not included in the scope of delivery)

Technical Data

Impact drill| GSB …| 10| 10 RE
1000 RE| 13| 13 RE| 16| 16 RE
---|---|---|---|---|---|---|---
Article number| 3 601…| B16 0..| 8161..| B17 0..| B171.. B17 6..| B18 O..| 8181.. B18 6..
Rated power input| W| 500| 500| 600| 600| 701| 701
Power output| W| 250| 250| 301| 301| 351| 351
No-load speed| min-¹| 2600| 0-2600| 2800| 0-2800| 3000| 0-3000
Max. speed under load| min-¹| 1610| 1610| 1570| 1570| 1640| 1640
Impact rate at no-load speed| min-¹| 41,600| 41,600| 44,800| 44,800| 48,000| 48,000
Rated torque| Nm| 1.5| 1.5| 1.8| 1.8| 2.0| 2.0
Speed preselection| | –| –| –| –| –| •
Clockwise/anticlockwise rota- tion| | –| •| –| •| –| •
Spindle collar diameter| mm| 43| 43| 43| 43| 43| 43
Max. drilling diameter| | | | | | |
– Concrete| mm| 10| 10| 13| 13| 16| 16
– Steel| mm| 8| 8| 10| 10| 12| 12
– Wood| mm| 20| 20| 25| 25| 30| 30
Chuck capacity| mm| 1.5–10| 1.5–10| 1.5–13| 1.5–13| 1.5–13| 1.5–13
Weight according to EPTA-Pro- cedure 01:2014| kg| 1.5| 1.5| 1.8| 1.8| 1.9| 1.9
Protection class| | | | | | |

The specifications apply to a rated voltage [U] of 230 V. These specifications may vary at different voltages and in country-specific models.

Assembly

• Pull the plug out of the socket before carrying out any work on the power tool.

Auxiliary handle (see figure A)

• Do not operate your power tool without the auxiliary handle (11).
• Before carrying out any work, make sure that the wing bolt is tightened. Loss of control can cause personal injury.

You can swivel the auxiliary handle (11) to any angle for a safe work posture that minimises fatigue.
Turn the wing bolt for adjusting the auxiliary handle (10) anticlockwise and swivel the auxiliary handle (11) into the required position. Then retighten the wing bolt (10) by turning it clockwise.

Setting the drilling depth (see figure A)
You can use the depth stop (12) to set the required drilling depth X.
Press the button for depth stop adjustment (9) and insert the depth stop into the auxiliary handle (11).
The fluting on the depth stop (12) must face downwards.
Pull the depth stop (12) far enough out that the distance between the drill bit tip and the edge of the depth stop (12) corresponds to the required drilling depth X.

Changing the tool

• Wear protective gloves when changing tools. The drill chuck may heat up significantly when it is used for long periods.

Keyless chuck (see figure B)

The drill spindle is locked when the on/off switch (6) is not pressed. This makes it possible to change the application tool in the drill chuck quickly, conveniently and easily.
Open the keyless chuck (1) by turning it in the direction of rotation ➊ until the tool can be inserted. Insert the tool.
Firmly tighten the sleeve of the keyless chuck (1) by turning it by hand in the rotational direction ➋ until it stops clicking.
This will automatically lock the drill chuck.
Hold the rear sleeve (3) of the keyless chuck (1) firmly and turn the front sleeve (2) in the rotational direction ➊ until the tool can be inserted. Insert the tool.
Hold the rear sleeve (3) of the keyless chuck (1) and firmly tighten the front sleeve (2) by hand in the rotational direction ➋ until it stops clicking. This will automatically lock the drill chuck.
The lock will disengage again if you turn the front sleeve (2) in the opposite direction to remove the tool.
The lock will disengage again if you turn the sleeve in the opposite direction to remove the tool.
Keyed chuck (see figure C)
Open the keyed chuck (15) by turning it until the tool can be inserted. Insert the tool.
Insert the chuck key (14) into the corresponding holes of the keyed chuck (15) and clamp the tool evenly.
Screwdriving tools (see figure D)
You should always use a universal bit holder (16) when using screwdriver bits (17). Only use screwdriver bits that fit the screw head.
For screwdriving, make sure the “drilling/impact drilling” selector switch (4) is always set to the “drilling” symbol.

Changing the Drill Chuck

• Pull the plug out of the socket before carrying out any work on the power tool.

Removing the Drill Chuck (see figure E)
To remove the keyless chuck (1), clamp a hex key (18) in the keyless chuck (1) and position an open-ended spanner (19) (width across flats: 12) against the spanner flat of the drive spindle.

Place the machine on a firm surface, e.g. a work bench.
Hold the open-ended spanner (19) in place and loosen the keyless chuck (1) by turning the hex key (18) in the rotational direction ➊. A tightly seated keyless chuck can be loosened with a light blow on the long shaft of the hex key (18).
Remove the hex key from the keyless chuck and completely unscrew the keyless chuck from the machine.
The keyed chuck (15) can be removed in the same way as described for the keyless chuck.

Fitting the Drill Chuck (see figure F)
To assemble the keyless chuck, perform the same steps in reverse order.
The drill chuck must be tightened using a tightening torque of approx. 30–35 Nm.

Dust/Chip Extraction
Dust from materials such as lead-containing coatings, some wood types, minerals and metal can be harmful to one’s health. Touching or breathing-in the dust can cause allergic reactions and/or lead to respiratory infections of the user or bystanders.
Certain dust, such as oak or beech dust, is considered carcinogenic, especially in connection with wood-treatment additives (chromate, wood preservative). Materials containing asbestos may only be worked by specialists.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the materials to be worked.

• Avoid dust accumulation at the workplace. Dust can easily ignite.

Operation

Starting Operation

• Pay attention to the mains voltage! The voltage of the power source must match the voltage specified on the rating plate of the power tool. Power tools marked with 230 V can also be operated with 220 V.
•  Products that are only sold in AUS and NZ: Use a residual current device (RCD) with a nominal residual current of 30 mA or less.

Setting the Rotational Direction (see figures G–H)
(GSB 10 RE/GSB 13 RE/GSB 16 RE/GSB 1000 RE)
The rotational direction switch (8) is used to change the rotational direction of the power tool. However, this is not possible while the on/off switch (6) is being pressed.
Right  rotation: To drill and to drive in screws, press the rotational direction switch (8) through to the left stop.
Left Rotation: To loosen and unscrew screws and nuts, press the rotational direction switch (8) through to the right stop.

Setting the Operating Mode

Drilling and screwdriving
Set the selector switch (4) to the “drilling” symbol.

Impact drilling
Set the selector switch (4) to the “impact drilling” symbol.
The selector switch (4) clicks into place and can also be actuated when the motor is running.

Switching on/off
To start the power tool, press and hold the on/off switch (6).
Press the lock-on button (5) to lock the on/off switch (6) in this position.
To switch off the power tool, release the on/off switch (6);
or, if the switch is locked with the lock-on button (5), briefly press the on/off switch (6) and then release it.
Setting the Speed/Impact Rate (GSB 10 RE/GSB 13 RE/ GSB 16 RE/GSB 1000 RE) You can adjust the speed of the power tool when it is on by pressing in the on/off switch (6) to varying extents.

A light pressure on the on/off switch (6) results in a low rotational speed. Increased pressure on the switch causes an increase in speed.
Preselecting the Speed/Impact Rate (GSB 16 RE) You can preselect the required speed/impact rate using the speed preselection thumbwheel (7), even during operation.
The required speed/impact rate is dependent on the material and the work conditions and can be determined by practical trials.

Practical Advice

• Pull the plug out of the socket before carrying out any work on the power tool.
• Only apply the power tool to the screw/nut when the tool is switched off. Rotating tool inserts can slip off.

After working at a low speed for an extended period, you should operate the power tool at the maximum speed for approximately three minutes without load to cool it down.
To drill into tiles, set the selector switch (4) to the “drilling” symbol. After drilling through the tile, set the selector switch to the “impact drilling” symbol and drill with impact.
Use carbide drill bits when working with concrete, stone and masonry.
When drilling into metal, only use sharpened HSS drills (HSS = high-speed steel) which are in perfect condition.
The Bosch accessory range guarantees appropriate quality.
Using the drill bit sharpener (accessory), you can effortlessly sharpen twist drill bits with a diameter of 2.5–10 mm.

Maintenance and Service

Maintenance and Cleaning

• Pull the plug out of the socket before carrying out any work on the power tool.
• To ensure safe and efficient operation, always keep the power tool and the ventilation slots clean.
  In order to avoid safety hazards, if the power supply cord needs to be replaced, this must be done by Bosch or by an after-sales service centre that is authorised to repair Bosch power tools.

After-Sales Service and Application Service
Our after-sales service responds to your questions concerning maintenance and repair of your product as well as spare parts. You can find explosion drawings and information on spare parts at: www.bosch-pt.com
The Bosch product use advice team will be happy to help you with any questions about our products and their accessories.
In all correspondence and spare parts orders, please always include the 10‑digit article number given on the nameplate of the product.
Malaysia
Robert Bosch Sdn. Bhd.(220975-V) PT/SMY
No. 8A, Jalan 13/6
46200 Petaling Jaya
Selangor
Tel.: (03) 79663194
Toll-Free: 1800 880188
Fax: (03) 79583838
E-Mail: kiathoe.chong@my.bosch.com
www.bosch-pt.com.my

You can find further service addresses at: www.bosch- pt.com/serviceaddresses
Disposal
The power tool, accessories and packaging should be recycled in an environmentally friendly manner.
Do not dispose of power tools along with household waste.

Robert Bosch Power Tools GmbH
70538 Stuttgart
GERMANY
www.bosch-pt.com

Documents / Resources

| BOSCH GSB Professional Impact Drill [pdf] Instruction Manual
GSB Professional, GSB Professional Impact Drill, Impact Drill, Drill
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>