Kraus KPF-2631 Single Handle Commercial Style Kitchen Faucet Instruction Manual

Oletto™ Single Handle
Commercial Style
Kitchen Faucet
KPF-2631

KPF-2631 Single Handle Commercial Style Kitchen Faucet

Congratulations on the purchase of your new  Kraus plumbing fixture!
Please keep the box and packaging materials until your product is  completely installed. If you have any questions, require technical assistance or have any problems with your product:
STOP DO NOT RETURN TO STORE
Please contact our Customer Service Team 1-800-775-0703 / customerservice@kraususa.com
Have the model number available and retain a copy of your receipt with purchase date for reference.
If for any reason this product does not meet your expectations, please be sure to repack this product in the original box and packaging material to avoid damage during transit.
Prior to Installation:

• Make sure you have all necessary parts by checking the diagram and parts list. If any part is missing or damaged, please contact Kraus Customer Service at 800-775-0703 for a replacement.
• Read all instructions and safety warnings and ensure you have all tools, parts, and equipment necessary for a safe installation.
• Turn off the hot and cold water supply at the angle stops and turn on the old faucet to release any built up pressure. Remove existing faucet.
• Pre-drilled hole size requirement: 1 3/8″ (min)
• Max countertop thickness: 2 3/8”

For technical assistance or replacement parts, please contact Kraus Customer Service and one of our representatives will be happy to help: Toll-Free: 800-775-0703 or Customerservice@kraususa.com
Tools Required

Care & Maintenance

To keep the product clean & shining, follow the steps below:

1. Rinse with clean water & dry with a soft cloth
2.  Do not clean with soaps, acid, polish, abrasives or harsh cleaners
3.  Do not use cloth with a coarse surface
4.  Unscrew the aerator and clean when necessary

• This installation manual is subject to change without further notice. Diagram and Parts List A. Sprayer
  B. Faucet Body
  C. Escutcheon
  D. Gasket
  E. Easy Install Assembly
  F. Weight
  G. Weight Clip
  H. Quick Connector
  I. 2.5mm Hex Wrench
  J. 6mm Hex Wrench
  Faucet Dimensions

Installer Tip:

Shut off main water supply before installing new faucet.
Step 1a: Installing the easy install assembly (without escutcheon) Shut off the water supply. Remove the old faucet. Clean the mounting surface.
Check for the proper thickness of the sink or countertop. Insert the base (a) into the sink or countertop. If your model does have a escutcheon, skip to step 1 b.
NOTE: “Front” on the base (a) must face the front of the sink or countertop. The two mounting plates (b)b) on the base (a) must be loose movable during the installation of the base (a).
Step 1b: Installing the easy install assembly (with escutcheon) Place the escutcheon (C) and the gasket (D)D) on the s or countertop. Insert the base (a) into the escutcheon (C). Note: If the surface is uneven, use silicone under the gasket (D).
NOTE: “Front” on the base (a) must face the front of the sink or countertop. The two mounting plates (b)b) on the base (a) must be loose movable during the installation of the base (a).
Step 2: Installing the easy install assembly Press the base (a) so that it can not move, then turn the screw with the provided hex wrench (C, HEX: 6.0mm) clockwise, as shown in Fig 1. When the mounting plates (b) make contact with the sink (1), continue to turn the screw with the provided hex wrench (C, HEX: 6.0mm) clockwise, as shown in Fig 2, until the base (a) is completely tightened and secured, as shown in Fig 4.
Step 3: Installing the faucet Insert the hose (1), supply lines (2) and quick connect hose (3) one by one through the hole of the base (a). Carefully insert the hoses into the base. Place the faucet assembly onto the base (a) as shown in the above figure. Secure the faucet assembly (B) by tightening the set screw with the provided hex wrench (I, Hex: 2.5 mm).
Step 4: Installing the counterweight Install the weight clip (G) at the point of the hose marking “weight here”. Insert the weight (F) onto the weight clip (G) by sliding it down onto the weight clip (G).
Step 5: Connect waterlines to main valve Attach waterlines to angle stops and tighten until snug. Turn on angle stops and check for leaks (DO NOT TURN FAUCET ON).
NOTE: Please make sure filter washers are installed before connecting to the main valve.
Step 6: Flush faucet NOTE: Please make sure the washer (1) is installed before attaching the spray head to the hose.
Pull the hose assembly out of the spout and remove the spray head (A) by unscrewing it from the hose in a counterclockwise direction. Be sure to hold the end of the hose down into the sink and turn the faucet on to the warm position where it mixes hot and cold water. Flush the water lines for one minute. This flushes away any debris that could cause damage to internal parts. Check for leaks. Retighten any connections if necessary, but do not overtighten. Reinstall the spray head (A) by hand tightening it back onto the sprayer hose. After installation is completed, turn on the hot and cold water supplies. Check for leaks.

Replacement Parts

*Denotes spray hose assembly color options: Spray hose assembly color options: Black hose with Matte Black connector (BLMB), Gray hose with Chrome connector (GRCH), Gray hose with Spot-Free Stainless connector (GRSFS);
Black hose with Spot-Free Antique Champagne Bronze connector (BLSFACB); Black hose with Brushed Brass (BLBB); **Denotes faucet component color options: CH – Chrome

• SFS – Spot Free Stainless Steel
• MB – Matte Black
• BB – Brushed Brass
• SFACB – Spot Free Antique Champagne Bronze
• BL – Black
• GR – Grey

Troubleshooting

If you have followed the instructions carefully and your faucet still does not work properly, take the following corrective steps:

(13). Loosen the screw (12) with the hex wrench (20).
Remove the handle (11) and cap (10). Tighten the bonnet nut (9) with an adjustable wrench.
The aerator has an irregular or reduced water flow.| The aerator is dirty or misfitted.| Remove the aerator and check for debris. Ensure that the rubber washer is properly
installed.
Water will not shut off completely.| Cartridge may need to be adjusted or replaced.| Remove the index (13). Loosen the screw (12) with the hex wrench (20). Remove
the handle (11) and cap (10). Loosen the bonnet nut (9} with an adjustable wrench. Remove the cartridge (8). Check for cracks.
There is a low flow of water.| The filter washers in the hose connectors are dirty.| Turn off the water supply at the water valves and unscrew the hose connectors from the water supply lines. Clean the filter washers in the water lines with hot water, removing any debris or calcium build up.

Codes/Standards Applicable: Faucet – Lifetime Limited Warranty
Kraus USA Plumbing, LLC (“Kraus”) extends this warranty to the original purchaser for personal household use of the Faucet when purchased from an authorized Kraus dealer and in the location of original installation. This warranty is
non-transferable.
Kraus warrants the structure and finish of the Faucet to be free from defects in material and workmanship under normal usage for as long as the original purchaser resides in the residence in which the Faucet was first installed.
Kraus warrants the Faucet’s sprayhood assembly (including the engine, aerators, structure, restrictors, back flow preventers, sprayer hoses, braided supply line hoses which encompasses nylon, silicon and stainless steel) of the product to be free from defects in material and workmanship under normal usage for a period of one (1) year from the date of purchase.
Kraus warrants the Faucet’s cartridge to be free from defects in material and workmanship under normal usage for a period of five (5) years from the date of purchase.
Any product reported to the authorized dealer or to Kraus as being defective within the warranty period will be repaired or replaced with a product of equal value at the option of Kraus.
Commercial Warranty
Kraus USA Plumbing, LLC (“Kraus”) warrants its Products for a period of one (1) year to commercial purchasers of Products used in industrial, commercial and business applications.
Care and Cleaning Instructions
Certain cleaning products may cause damage to a Product’s finish and use of the following on the Product will void this warranty:

• Abrasive cleaners such as powders, bleach, ammonia, alcohol or chorine
• Abrasive pads, steel wool or wire brushes

What is Not Covered
This warranty does not cover Products that were discontinued when purchased or display Products, whether such Products were purchased at discount outlets, unauthorized dealers, and/or sold on clearance. This warranty does not
cover any free gifts included with purchase.
This warranty does not cover damage resulting from neglect, misuse (including use for an unintended application), abuse, carelessness, accident, hard water or mineral deposits, exposure to corrosive materials, improper maintenance, alteration of the Product, or failure to follow care, cleaning or installation instructions enclosed with your Product. Kraus recommends that all Kraus Products be installed by a fully licensed and insured trade professional with experience in the installation of bathroom and/or kitchen manufactured goods.
How to Make a Warranty Claim
If you are a consumer purchaser, please contact a Kraus Customer Service Representative at: Kraus USA Plumbing, LLC
12 Harbor Park Drive
Port Washington, NY 11050
Toll-free 800-775-0703
Customerservice@kraususa.com
If you are a plumbing contractor or trade professional, please contact a Kraus Pro Representative at: Kraus USA Plumbing, LLC
12 Harbor Park Drive
Port Washington, NY 11050
516-801-8955
Proservice@kraususa.com
If you are an authorized partner, please contact a Partner Support Representative at: Kraus USA Plumbing, LLC
12 Harbor Park Drive
Port Washington, NY 11050
516-801-8954
Partnersupport@kraususa.com
In requesting warranty service, please be ready to provide your proof of purchase and a description of the problem. Shipping charges will be covered for the first (1) year of the warranted replacement part or product (HI, AK, and Puerto Rico shipping charges may apply). International shipping fees are not included.
Limitation on Duration of Implied Warranties
Please note that some states/provinces (including Quebec) do not allow limitations on how long an implied warranty lasts, so the below limitations may not apply to you. TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, ANY IMPLIED WARRANTY, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND OF FITNESS FOR A PARTICULAR PURPOSE, IS LIMITED TO THE STATUTORY PERIOD OR THE DURATION OF THIS WARRANTY, WHICHEVER IS SHORTER.
Limitation of Special, Incidental or Consequential Damages
Please note that some states/provinces (including Quebec) do not allow the exclusion or limitation of special, incidental or consequential damages, so the below limitations and exclusions may not apply to you. TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS WARRANTY DOES NOT COVER, AND KRAUS USA PLUMBING, LLC SHALL NOT BE LIABLE FOR, ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING LABOR CHARGES TO REPAIR, REPLACE, INSTALL OR REMOVE THIS PRODUCT), WHETHER ARISING OUT OF BREACH OF ANY EXPRESS OR IMPLIED WARRANTY, BREACH OF CONTRACT, TORT, OR OTHERWISE.
This warranty gives you specific legal rights, and you may also have other rights which vary from state/province to state/province.
Download the Kraus Care & Maintenance Guide at:
http://www.kraususa.com/maintenance
IMPORTANT\
Register Your Kraus Product
Activate Your Warranty Access Premium Customer Support Get Product Information

REGISTER TODAY
http://www.kraususa.com/registrationwww.kraususa.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>