BLACKSPIDER BS100BT One Way Alarm User Manual
- June 14, 2024
- BLACKSPIDER
Table of Contents
BLACKSPIDER BS100BT One Way Alarm
Product Information
The Blackspideraudio BS100BT is a car alarm system designed to provide security and convenience for your vehicle. It is equipped with Bluetooth technology, allowing you to control the alarm system using your smartphone. The alarm system is compatible with both iOS and Android devices.
- Manufacturer : blackspideraudio
- Model : BS100BT
- Website : www.blackspider.co.za
Product Usage Instructions
Downloading and Installing the Bluetooth APP
To control the car alarm system using your smartphone, you need to download
and install the Bluetooth APP. Follow the steps below:
- Scan the QR Code provided in the user manual or on the product.
- Once the QR Code is scanned, it will redirect you to the download page of the APP.
- Download and install the APP on your smartphone.
Pairing the Alarm System with your Smartphone
After installing the APP, you need to pair the alarm system with your
smartphone. Follow the steps below:
- Open the Bluetooth APP on your smartphone.
- Select “Settings” within the APP.
- Long press the “Learning Code” option within the settings.
- Within 10 seconds, simultaneously press both the “Lock” and “Unlock” buttons on your car remote to initiate pairing mode.
- If successful, you will receive a notification confirming the pairing.
Controlling the Alarm System
Once the alarm system is successfully paired with your smartphone, you can
use the Bluetooth APP to control your vehicle. Follow the steps below:
- Return to the control page within the Bluetooth APP.
- Use the “Lock” button on the APP to lock your vehicle.
- Use the “Unlock” button on the APP to unlock your vehicle.
Specifications
- Compatibility: iOS and Android
- Manufacturer: blackspideraudio
- Model: BS100BT
Frequently Asked Questions (FAQ)
Can I use the car alarm system with both iOS and Android devices?
Yes, the Blackspideraudio BS100BT car alarm system is compatible with both
iOS and Android devices.
How do I pair the alarm system with my smartphone?
To pair the alarm system with your smartphone, follow the instructions
provided in the user manual. Open the Bluetooth APP, go to settings, long
press “Learning Code,” and simultaneously press the “Lock” and “Unlock”
buttons on your car remote within 10 seconds.
What should I do if the pairing process fails?
If the pairing process fails, make sure you are following the instructions
correctly. Ensure that your smartphone’s Bluetooth is turned on and that you
are within range of the car alarm system. If the issue persists, consult the
troubleshooting section of the user manual or contact Blackspideraudio
customer support.
Congratulations on the purchase of your state-of-the-art
“Bla.ckSpider”vehicle security system. Installation of this product by anyone
other than an authorized dealer voids the warranty. This owner’s guide should
help you to get the most out of your system. Please take the time to read it
before using the system. User Manual for 85100-BT
Features
- 12V Car Alarm
- Controlled by microprocessor system
- Two remotes with 4 buttons
- Up to 4 programmable remotes
- Frequency signal 433 MHZ (Impossible to be scanned)
- Remote Panic
- Car finder using remote
- Silent arming and disarming using the remote
- Boot release using remote
- One negative Aux output for optional modules
- LED indicator
- Auto arming (Programmable)
- Automatic auto arming (Accidental Disarming) (Programmable)
- Locks with auto arming (Programmable)
- Electronic siren with 120 Oba
- Valet mode using the reset button
- Anti-hijack by remote (Programmable)
- Anti-hijack by opening the driver’s door (Optional)
- Anti-hijack by ignition(Programmable)
- Flashing of car lights when the anti-hijack system is activated
- Exclusion of defective zones
- Function programming by software
- Manual disarming by a secure PIN code(Programmable)
- Last state memory
THE REMOTE:
Remote buttons functions:
With the ignition off:
- Button 1: Arm the system + Car Finder.
- Button 2: Disarm the system.
- Button 4: Channel 2, to open the boot.
- Buttons 1 and 2 pressed at the same time: Panic. Buttons 3 and 4 pressed at the same time: Channel 3 Button 1 then button 2: Impact sensor off.
- Button 3 then button1: Silent arming.
- Button 3 then button 2: Silent Disarming.
With the ignition ON:
- Button 1: Lock the doors.
- Button 2: Unlock the doors.
- Button 3: Anti hijack.
- Button 4: CHANNEL2 To open the boot.
- Buttons 1 and 2 pressed at the same time: Panic. Buttons 3 and 4 pressed at the same time: CHANNEL 3
Reset button:
- Cancel Auto-arming if activated.
- Reset the Anti hijack by ignition mode.
- Activate Valet mode.
- Deactivate the alarm when remotes are not working.
- To program new remotes.
LED Indicator:
The LED assists in notifying you about the 7 functions of the car alarm
system.
Remote Functions
- Button 1: Arm/lock the doors with the ignition off. Press button 2 within the first 3 seconds after arming the system to turn the impact sensor off.
- With the ignition ON: press to lock the doors.
- Button 2: Disarm/ unlock the doors with the ignition OFF.
- With the ignition ON: Press to unlock doors.
- Button 3 : (Anti-Hijack) Press to activate the Anti-Hijack system.
- Button 4: (Channel 2 / Channel 3) Press it for 3 seconds and you will activate channel 2. This channel is used for opening the electronic boot. Press the buttons 3 and 4 at the same time and you will activate Channel 3.
- Buttons 1 and 2 simultaneously: Press and hold the buttons 1 and 2 simultaneously for 3 seconds to activate the Panic.
- Button 3 and then Button 1 🙁 Silent arming)
- With the ignition OFF: Press button 3 and then button 1. The system will be armed in silent mode. The indicator lights will flash.
- Button 3 and then Button 2: (Silent Disarming)
- With the system armed: Press button 3 once and then press button 2 once. The system will be disarmed in silent mode. The indicator lights will flash.
Buttons 3 and 4 simultaneously: Press for 3 seconds to activate channel 3 to control an additional convenience option.
SECURITY CODES OF REMOTES:
- The system has two remotes.
- Each one has a unique code.
- You can program up to 4 remotes.
HOW TO ARM THE SYSTEM:
Arming the system with remote:
With the doors closed, press button 1 once to arm the system, while the
ignition is OFF. The lights will flash and the siren will sound once. The LED
will blink slowly confirming that the system is armed.
Bypassing of defective areas:
Your system is equipped with circuitry that will exclude repetitive trigger
sequences due to faulty door pin switches or environmental conditions such as
thunder. When arming the alarm, and one zone is defective (For example, if the
boot is not closed), the siren will sound 3 times and the lights will flash 3
times simultaneously indicating that one area is defective. When this happens
the defective area will be excluded automatically and the car will be
protected.
Bypassing the shock sensor with the remote:
Press button 1 of the remote to the arm, and within 3 seconds after arming ii
press button 2, the siren will sound once to confirm the exclusion of the
shock sensor. This function is necessary when parked close to an area with
high traffic or thunder. When you disarm the system, the shock sensor will
reset.
Auto Arming (Programmable):
The system can also be programmed to arm itself automatically. If the system
is programmed for auto arming, it will automatically arm after the ignition is
turned off and the system “sees” you leave the vehicle by opening and closing
a door. The lights will flash one time, the siren will sound one time and the
LED will start to blink slowly, confirming the arming of the system. If the
central locking system is connected and programmed the doors will lock. If,
within 30 seconds before arming, one door is opened, the auto arming will be
on a wail mode. When the door is closed again the system will restart the auto
arming mode.
NOTE : The system will auto-arm and lock doors if selected. Please do not leave keys inside the car.
Alarm system Armed and Activated:
When the alarm system is armed, the LED will blink slowly. If a door is
opened, the siren will start to sound and the lights will blink for 30
seconds, if the door is still open after 30 seconds, the siren will continue
ringing with the lights flashing for 3 minutes, after 3 minutes the alarm
system will exclude the door sensors and continue protecting the car with the
other sensors. If the door is closed within the first 30 seconds after the
sound of the siren, the siren will be silent and the lights will stop blinking
30 seconds after the door is closed. When you disarm the system, the siren
will sound 4 times and the lights will flash 4 times, this will indicate that
the alarm was triggered and the LED will continue blinking until the ignition
is switched on.
Disarming of the system:
When the system is armed, press button 2 of the remote once, the siren will
sound 2 times and the lights will flash 2 times indicating that the system is
disarmed. The immobilizer circuit (optional if connected) will be deactivated
and the LED will be OFF. If the central locking system is connected the doors
will be unlocked. If you press button 2, the system will send a signal to open
the doors again.
Silent Arming:
First press button 3 once and then press button 2 of the remote to disarm in
silent mode. If the alarm was triggered, after disarming the system in silent
mode the siren will sound 3 times informing you that the alarm was triggered.
Automatic rearming after accidental disarming:
This function is programmed in the system memory like a preventative function.
In this case, it is necessary to disarm the system using the remote and if you
are not going to open the car or move the ignition switch to the ON position,
the LED indicator will start to blink very fast, after 90 seconds the system
will be armed again confirming with one sound of the siren and one flash of
the lights. If the function 15 is programmed to the ON position the doors will
be locked protecting the car again until you disarm the car.
Anti-Hijack by Doors:
With the ACC on, if you open and then close the driver’s door, the LED light
will flash and the car lights will flash two times indicating the activation
of the Anti-Hijack. If the sound is programmed, the siren will sound two
times. For the anti-hijack function, you must connect the anti-hijack wire to
a negative door switch.
Anti-Hijack by remote:
This function is used to activate the anti-hijack by pressing button 3 for
three (3) seconds while the car is running, the lights will flash two limes
and the LED light will start to blink indicating the anti-hijack is activated.
If the sound is programmed the siren will sound two times. This function is
programmable(see programming table)
Anti-Hijack by ignition:
This function of the anti-hijack is automatically activated each time you turn
the ignition switch from OFF to ON. It doesn’t need a door to be opened ora
remote to be pressed. When ii is activated the LED starts to blink, the lights
will flash two limes and if the sound is programmed the siren will sound two
times. This Function is programmable. (see programming table)
Anti-Hijack proximity sensor:
This function is used to activate the anti-hijack when the extra remote (see
below how to program) is away from the car for more than 60 seconds when it is
running. After 60 seconds the anti-hijack will be activated, the LED will
start to blink, the lights will flash two times and if the sound is programmed
the siren will sound twice. This Function is programmable. (See programming
table).
How to turn on the remote:
Press the button on the remote and hold it pressed, the red LED of the
remote will flash once. After 3 seconds the LED of the remote will be on for 2
seconds. Release the button on the remote. The remote will send one signal to
the receptor every 6 seconds. When the battery of the remote is depleted the
red LED on the remote will start to blink. You need to replace the battery.
How to turn off the remote:
Press the button of the remote and hold it, the red LED of the remote will
flash once and then turn off. After 3 seconds, the LED of the remote will
blink 5 times, then release the button of the remote.
Anti-hijack activated:
When the system goes into anti-hijack mode, the lights of the car will
flash 2 times, if function 13 is activated the siren will sound 2 times, and
the LED will start to blink slowly. After 30 seconds the lights start to blink
and the siren will start to sound. After 15 seconds of the siren sounding, and
if function 14 is programmed, the anti-hijack will be activated intermittently
causing the car to slow down, then after 15 seconds the anti-hijack will be
fully activated turning off the engine and locking the doors. The siren will
sound continuously.
How to cancel the anti-hijack systems:
- To cancel the anti-hijack system before the siren starts to sound or within 60 seconds after the activation, press and release the reset button one time.
- To cancel the anti-hijack after the siren starts or after 60 seconds of the activation, move the ignition switch to the ON position, press the reset button the amount of times as the security code (default is 1 time), and wait 3 seconds, this 3 seconds is to confirm that the security code was entered correctly.
Valet mode and reset button:
You can prevent your security system from automatically arming and triggering
by using Valet Mode. This is very useful when washing the vehicle or having it
serviced. In Valet Mode, the security system will not arm, even with the
remote, but all convenience functions (door locks, trunk release, etc.) will
continue to work normally. To activate the valet mode, you have to disarm the
system and move the ignition switch to the ON position, then press and hold
the reset button for 3 seconds. When this mode is activated the LED will be on
all the time. When the valet mode is activated, the immobilizer circuit and
the alarm system will be inactive; but you can still use the car finder, panic
mode, boot opening, opening or closing of the doors, etc. To exit the valet
mode, you have to move the ignition switch to the ON position, and then press
the reset button once. The LED will turn OFF indicating the deactivation of
the valet mode.
Disarming of the system by the reset button:
If the battery on your remote is low, or if the remote is lost or faulty, you
can disarm the system with the reset button.
- FIRST : With the system armed, open the driver’s door, the siren will start to sound.
- SECOND : Move the ignition switch to the ON position, within 10 seconds press the reset button the number of times as the security code (Factory default is one). The siren will continue to sound for 3 seconds and if the security code is correct, the system will be disarmed.
LED indicator:
The LED indicator is designed to bring information about the state of the
alarm system to the car owner. Additionally, it can alert you if someone tries
to steal the car. The LED should be installed in a place where the driver can
see it easily.
The LED has 7 different modes:
- LED off : The alarm is disarmed.
- LED on: The alarm is on Valet mode.
- LED blinking slowly: The alarm is armed.
- LED blinking fast: 30 seconds-Automatic arming. 90 seconds- Automatic Re-Arming.
- LED flashing 2 times with pause : The alarm was triggered due to an attempted theft by opening the boot.
- LED flashing 3 times with pause: The alarm was triggered due to an attempted theft by opening the doors.
- LED flashing 4 times with pause: The alarm was triggered due to an attempted theft by opening the bonnet.
Confirmation by siren and lights:
With the electronic siren and the lights of the car, the security system
will indicate to you the different events associated with the protection of
your car.
- One sound of the siren and flashing of the lights once will tell you the system is armed.
- One sound of the siren within the first 3 seconds, after arming, will tell you the exclusion of the shock sensor.
- One sound of the siren after turning the ignition OFF, will tell you that the system is in valet mode.
- Two sounds of the siren and the flashing of the lights twice will tell you the alarm system is disarmed.
- The siren sounds loud and the lights are blinking, the vehicle is being tampered with.
- With four sounds of the siren and flashing of the lights four times, after you disarm the system, the vehicle has been tampered with.
Shock sensor Alert:
The shock sensor is designed to tell you by way of the siren if the car has
a low or hard impact. If the impact is low the siren will sound intermittently
for 2 seconds and if the impact is hard the siren will sound for 30 seconds.
False alerts:
If the alarm is triggered, the siren will sound for 30 seconds. If the
siren sounds for more than 30 seconds, after 3 minutes the siren will turn off
and the system will bypass the faulty zone, protecting the car with the rest
of the sensors. This also applies to the shock sensor after 1 O alerts.
Programming functions:
Up to 16 different functions can be programmed into memory.
How to program functions
Entering the programming mode:
- Switch ignition from ON to OFF position.
- Within 7 seconds of switching to the OFF position, press and release the reset button 6 times.
- The lights will be on and the siren will sound once indicating that you are now in the programming mode. You have 10 seconds to select the function that you want to program. If within 10 seconds you fail to program anything, the system will exit the programming mode.
- Within 10 seconds, press and release the reset button corresponding to the number of the function that you want to program, and the siren will beep indicating the same quantity of tones. For example, if you want to program the system with the automatic arming feature, press the reset button two times, and the siren will then beep twice.
- To activate the function, press button 1 on the remote, the siren will sound once and the LED will light up. This process will confirm that the function is activated.
- To deactivate the function, press button 2 of the remote, the siren will beep twice and the LED will switch OFF. You have 1 O seconds to activate or deactivate the function. If you do not select an option, the system will exit the programming mode and the siren will beep 5 times to confirm this and the LED will switch off.
- if you need to program other functions, repeat steps 4,5,6 to activate or deactivate other functions.
- To exit the programming mode, wait 10 seconds or move the ignition switch to the ON position. The siren will beep 5 times and the LED will switch OFF.
PROGRAMMING FUNCTIONS
Programming the pulse time of the central locking system:
The central locking factory default pulse is set to 0.8 seconds. This time can
be extended to 4 seconds by cutting the jumper No.1.
Double pulse for central locking system:
The alarm comes programmed from the factory with the function of opening the
central locking system with a double pulse. Press button 2 of the remote to
disarm the alarm, the system will send the first pulse of opening, then press
button 2 of the remote again and it will send a second pulse to open the
central locking system.
Programming and functions of the Channel 3
Channel 3 of the alarm system is completely independent of channel 2, this was
designed to be used to activate optional modules like auto engine start,
electric windows, etc. To operate this function press buttons 3 and 4 of the
remote simultaneously.
Channel 3 has three kinds of signals:
- Pulse : Press buttons 3 and 4 of the remote simultaneously for 3 seconds to activate a pulse. If you hold the buttons pressed the pulse will change to 25 seconds or until you release the buttons.
- Constant : Press buttons 3 and 4 of the remote simultaneously for 3 seconds, and you will obtain a constant pulse for channel 3, press and release buttons 3 and 4 simultaneously again and it will deactivate pulse 3.
- Permanent : Press buttons 3 and 4 of the remote simultaneously for 3 seconds, and you will obtain a constant pulse of 30 seconds for channel 3.
The following can be selected in the programming mode for function 11.
Programming the Function for Channel 3:
- Pulse : Press button 1, the siren will sound once.
- Constant : Press button 2, the siren will sound twice.
- Permanent : Press button 3, the siren will sound 3 times.
Hooter Function:
The hooter can be programmed with 4 different functions but only one of
them can be selected.
- Dome Light: It will turn on the dome lights of the car when you disarm the alarm, and the dome light will blink intermittently when the siren sounds as a result of a panic or alarm being triggered.
- Immobilizer: When arming the alarm, it holds a constant pulse that can be used for a second current cut or additional active sensors.
- Power windows: When arming the alarm, it will send a pulse of 30 seconds that can be used to activate an optional module for power windows.
- Intermittent Hooter: The hooter will sound intermittent when the alarm is triggered and will give one sound when armed and 2 sounds when disarmed. It will also work with the output functions of the siren (Independent).
Programming the frequency of the hooter:
- Dome Light: Press button 1, and the siren sounds once to confirm.
- Current Cutter : Press button 2, and the siren sounds twice to confirm.
- Power Window : Press button 3, and the siren will sound three times to confirm.
- Intermittent hooter : Press button 4, and the siren will sound four times to confirm.
Programming a new remote and proximity remote:
The alarm is designed to memorize 4 different remotes.
PRECAUTION! When you program one remote, the rest of them will be erased from the memory, so please be sure to program all at the same time. The proximity remote must be the last one to be programmed.
Steps to follow when programming a remote:
- Turn the ignition to the ON position.
- Within the first 5 seconds of turning the ignition to the ON position, press and release the reset button 6 times. The siren will confirm with one loud sound, and you have 10 seconds to start programming the remotes. (If you do not start before the 10 seconds or turn the ignition switch to OFF, the system will exit the programming mode, and the siren will sound twice to confirm and the memory of the remotes will not be erased).
- Press and release button 1 of the remote to be programmed, and he siren will sound once to confirm the programming of this remote, from this moment the old transmitters are erased.
- If you desire to program a second remote, repeat step 3 and the siren will confirm with 2 sounds, 3 times when you program the third remote, and after the fourth one, the system will close the programming mode.
- Turn the ignition switch OFF or wait for 10 seconds. The siren will beep two limes indicating that the system is out of the remote learning mode.
- lf the anti-hijack by ignition is activated, first put the system into valet mode and follow the steps from 1 to 5.
- To program the additional remote for the anti-hijack by proximity mode, first program the alarm remotes. With the proximity remote off, press and release the button on the proximity remote, and the system will confirm with many sounds the memorization of the proximity remote.
Security code:
The factory default for security code is 1
You can disarm the alarm and anti-hijack by the ignition and program the security code with the reset button.
- Turn the ignition switch from OFF to ON 3 times, and the third time leave the ignition switch at the OFF position. All this must take less than 7 seconds.
- The siren will sound once and the lights will be on, the system is now in the PIN code programming mode.
- Press and release the reset button the same number of times as corresponds to the number of the PIN code that you select between 1 & 9. (Factory default code is 1)
- The siren will beep the same number of times as the PIN code that is selected and then exit the programming mode.
- Please store your PIN code as it will be required to disarm your alarm system in the case of an emergency, as well as, to deactivate the anti-hijack feature.
Identification of the installation wires:
RELAY CONNECTION OF HOOTER
ANTI-HIJACK CONNECTION USING DRIVER’S DOOR
CONNECTION USING CHANNEL 3 IN MODE B AND CHANNEL 2 Please scan the QR Code below to download the Bluetooth APP.
- Scan the QR Code.
- Download/Install the APP.
- Open the APP.
- Select “Settings”
- Long Press “Learning Code”
- Within 10 seconds press both the “Lock” and “Unlock” buttons at the same time to successfully pair the alarm.
- Once paired, return to the control page to Lock and Unlock your vehicle.
