BLACKSPIDER BS200BT Remote Alarm and Immobiliser User Manual

BLACKSPIDER BS200BT Remote Alarm and Immobiliser

Product Specifications

• Model: BS200BT
• Type: Alarm & Immobiliser
• Brand: Blackspider Audio
• Website: www.blackspider.co.za

Product Usage Instructions

Function Settings
To customize the functionality of the alarm and immobilizer, you can adjust the jumper positions as follows:

Locking, Short Circuit:
Pneumatic Central Locking
Auto Locking| JP2| Open Circuit: Ignition On, Auto Lock, Short Circuit: Ignition
On, Auto Lock is Disabled
Selective Unlocking| JP3| Open Circuit: Selective Unlocking Disabled, Short Circuit:
Selective Unlocking Enabled

Description of Functions & Features

Arming the Alarm & Immobilizer: Press the remote button to arm the system.

Frequently Asked Questions (FAQ)

Q: How do I program a new remote for the BS200BT?
A: To program a new remote, switch ignition on and press the reset button 5 times within 6 seconds. Indicator lights will come on, then press any button on the new remote. Finally, switch off the ignition to exit programming mode.

USER MANUAL & WIRING DIAGRAM
BS200BT
Alarm & Immobiliser

WIRING DIAGRAM

USER INSTRUCTIONS

FUNCTION SETTINGS

Locking Short Circuit: Pneumatic Central Locking
Auto Locking| JP2| Open Circuit: Ignition On, Auto Lock

Short Circuit: Ignition On, Auto Lock is Disabled

Selective Unlocking| JP3| Open Circuit: Selective Unlocking Disabled Short Circuit: Selective Unlocking Enabled
Note:

1. The default jumper settings is set to open circuit.
2. When changing jumper settings, unplug power then change jumper settings.

DESCRIPTION OF FUNCTIONS & FEATURES

1. ARMING THE ALARM & IMMOBILIZER
   Press the remote button , the siren will sound once and the indicator lights will flash once. If the vehicle has central locking, the door locks will lock. The status LED will light up. Arm the immobilizer and after 40 seconds it will enter into alarm mode if a door is opened the alarm will sound.

2. DISARMING THE ALARM & IMMOBILIZER
   Press the remote button , the siren will sound twice and the indicator lights will flash twice. If the vehicle has central locking, the doors will unlock and the immobilizer will disarm. If ignition is not switched on within 45 seconds, the system will rearm.

3. SELF ARMING IMMOBILIZER
   The Immobilizer will rearm after 45 seconds after disarming the alarm or 20 seconds after switching off ignition.
   Immobilizers status will be displayed with LED status light flashing once every second.

4. DISARMING THE SELF ARMED IMMOBILIZER
   Switch ignition on, and press the remote button , then press unlock , the status LED will go out.

5. ANTI-HIJACK IMMOBILIZER
   Switching on the ignition or opening a door will cause the anti-hijack to be armed. if reset button does not get pressed within 90 seconds, it will immobilize the vehicle.

6. INTRUSION DETECTION
   40 seconds after arming the alarm, if ignition is turned on or door is opened, alarm will sound and indicators will flash for 30 seconds unless the alarm is disarmed by the remote button .

7. MOTION SENSOR ISOLATION
   Press remote button , a second time after alarm is armed to disable motion sensor.

8. PANIC
   Press and hold lock button for more then 3 seconds, alarm will sound and indicators will flash for 30 seconds.
   Press the lock button once, will disarm the panic.

9. (OPTIONAL) SELECTIVE UNLOCKING
   Press unlock button once, will only unlock drivers door.
   Press unlock button twice, will unlock all doors.

10. (OPTIONAL) LOCK WITH IGNITION
    Turning ignition on will lock the doors if doors are closed.

11. VALET MODE
    In the event of emergency where remote doesn’t respond or when you are taking your vehicle for service, the vehicle should be in valet mode.
    Switch the valet mode on with override wire to ground. It will disable alarm & immobilizer.

12. PROGRAMMING A NEW REMOTE
    To programme new remote, switch ignition on and press reset button 5 times within 6 seconds. Indicator lights will come on then press any button on new remote.
    Then switch off ignition to exit programming mode.

NOTE
When new remote is programmed, the old remotes are erased. It is necessary to relearn remotes that are kept.

SPECIFICATIONS OF ALARM UNIT

ALARM UNIT

• Voltage: 12 – 14 V
• Standby Current Draw: <15mA
• Arming & Disarming Current: 10A
• Frequency: 433.92 MHz

MOBILE PHONE APP INSTALLATION METHOD (APP-07)

1. Download the Car Alarm APP
   • Scan the following QR to download APP.
   • Apple Phones (IOS): Search Car Alarm from the APP Store and download it.
2. How to connect your phone with your car
   • Turn on Bluetooth on your phone
   • Open the APP interface
   • Enable programming remote function on alarm then press any button on app and remotes to learn the bluetooth to alarm and relearn remotes. Then switch off ignition.

The Alarm can learn up to 4 devices (remotes and bluetooth phones).

References

• BlackSpider – Manufacturers of Blackspider products

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>