ansio 3390 Garden 5 litre Pressure Sprayer User Guide

: June 14, 2024
: ansio

Table of Contents

3390 Garden 5 litre Pressure Sprayer
GARDEN PRESSURE SPRAYER
USAGE INSTRUCTIONS
OPENING THE UNIT
INSTRUCTIONS
TROUBLESHOOTING
SPARE WASHERS INSTRUCTIONS
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

3390 Garden 5 litre Pressure Sprayer
User Guide

3390 Garden 5 litre Pressure Sprayer

ansio 3390 Garden 5 litre Pressure Sprayer

GARDEN PRESSURE SPRAYER

Do contact us regarding any aspect of your purchase by sending an email to support@ansio.com or calling us on 0 800 080 6781 (UK Toll Free) or +44 207 157 9795

NOTES FOR FIRST TIME USE
When using for the first time, test using just water. Add chemicals such as pesticides, insecticides or fertilizers ONLY after ascertaining that the equipment works as expected. This is for your own safety.

USAGE INSTRUCTIONS

NOTE
Before using the unit, screw the cap with ridges clockwise to make sure the green part of the handle is tightly locked to the black tube as shown in the figure.

FILLING THE TANK & USING THE UNIT

Fill in the white tank with water (up to maximum) and put the handle back into the container (Fig.1)
Turn the handle clockwise to screw it back in tightly (Fig.2)
To start pumping, press and turn the green handle in an anti-clockwise direction. Start pumping to build up the pressure and use the sprayer (Fig.3)

OPENING THE UNIT

Ensure that the upper part of the handle is tightly locked by inserting the two knobs/prongs on either side of the handle into the grooves and turned clockwise to lock (Fig.4)
Unlock the handle by rotating it in anti-clockwise direction (Fig.5)
Pull it out along with the black tube.

ansio 3390 Garden 5 litre Pressure Sprayer - cap1

INSTRUCTIONS

Lock the trigger for continuous spray
a) Press down the trigger.
b) Hold and push forward.
c) When the trigger is pressed all the way forward, the trigger is in the continuous spray mode.
d) Press down on the trigger and pull back to release the lock.
The safety pressure valve automatically releases excess pressure.

ansio 3390 Garden 5 litre Pressure Sprayer - trigger

TROUBLESHOOTING

PROBLEM	POSSIBLE CAUSE	RESOLUTION

Sprayer
Leaks| Loose connections: Typically leaks occur when the connectors are not screwed on tightly. Check all the connections to ensure that they are screwed on tight. (If this is not the reason, continue diagnosis checking the other options below)| Tighten the connections that are loose by screwing them tightly.
Missing or compromised washers:
It is possible that the washers preventing leaks at the connections are dry, cracked or missing causing the leaks. Unscrew the connection and inspect the state of the washers inside.| Replace worn out, cracked, or missing washers using the spare ones provided with the package.
Sprayer not spraying (or) Spraying weakly| Blocked Nozzle: If any solid matter enters the pump system (sand or dirt, for example), it can build up at certain points and cause a reduction or complete loss in spraying pressure. If the sprayer is not spraying, check the nozzle tip for any clogs or blockages.| If your nozzle is clogged, remove it from the trigger and try to clean it out and remove any solids in the lines that may be causing the block. If the nozzle tip is damaged or clogged to the point where it cannot be cleaned, it should be replaced
altogether.
Check Pump: Remove the pump and place the bottom of the pump against the flat palm of the hand, wearing rubber gloves, especially if a chemical is present. Pumping the pump should result in pressure being felt coming out of the black non return valve of the pump. If no pressure is felt, then the sprayer isn’t getting pressure.| Check, lubricate and replace faulty/missing/dry plunger O ring or leaking non return valve.
Check connections: The sprayer will lose pressure if the connections
are not secured or if the washers are dry, cracked or missing. Check the connection points have good washers and they are secure in place.| Check and replace ineffective washers using the spares provided with the package. Make sure that the connections are screwed tightly in place after replacing the washers.
Sprayer does not stop when Trigger is released| Grit/Dirt in the ON/OFF control:
This could be caused by Dirt or Grit in the trigger mechanism preventing the full release of the trigger. Check the trigger to see if there is dirt/grit lodged under it.| Gently lift the trigger and clean thoroughly using cloth or water as appropriate. This should restore the full function of the trigger.
Sprayer does not stop when Trigger is released| Air in Lance: Sometimes, air gets trapped in the lance, causing the liquid to continue to dribble even after the trigger is released.| To remove any air, hold the lance in a vertical position pointing away from you, toggle the trigger ON and OFF until the air is discharged, then continue spraying.
| Sprayer left with residual pressure| After each use, use the pressure release valve to vent any residual pressure before storing.
| Chemicals in the sprayer| After using sprayer to spray chemicals, clear the chemical from the sprayer, fill with water and spray to get rid of the chemicals such as weed killers. Not only will this mean you keep your sprayer in working order but will reduce the risk of forgetting the product you were using last time and potentially putting a weed killer onto a plant you do not want to kill!
| Sprayer left in the sun| The sun dries out the washers causing it crack and/or compromise their performance.
If you are still having issues, we suggest contacting us to help resolve the problem