Legrand ZLGP16 Wake Up Sleep Control Instruction Manual
- June 14, 2024
- Legrand
Table of Contents
Legrand ZLGP16 Wake Up Sleep Control
Wireless and battery less Wake Up/Sleep control
0 648 84L/85L – 0 677 86L/CB0423/CT0423/CN0423 0 770 57L – 6 000 84L 5 742
87/93 – 5 743 22 – 5 748 36 7 418 03L/33L/63L
Requires to install the connected starter pack and one or more «… with Netatmo» connected switch, micromodule or socket outlet
Module Control| Gateway power outlet and home/ away wireless master
switch| Mobile gateway power outlet
---|---|---
| 
| 
Pack contents:
Wake Up/Sleep control
Frequency bands: 2.4 – 2.4835 GHz Power level: < 20 mW
Start the configuration
Press the configuration button of Module Control or press the middle of the wireless master switch or on the configuration button of the mobile gateway power outlet until its light briefly turns green, and then stop pressing. All wired products lights will turn green.
| 
|
---|---|---
Pair the wireless, battery less switch to your connected installation.
Make sure that the indicator lights on the wired products are green and not flashing. If not, go back to step 1
-
A1 Tap 3 times any wired product “with Netatmo” with the wireless, battery less “Wake Up/Sleep control”. The light of the wired product flashes rapidly.
-
A2 For the specific case of the latching relay, press the main button of the latching relay until the configuration indicator flashes slowly in blue, release it then tap it 3 times with the wireless, battery less “Wake Up/Sleep control”. The indicator light of the wired product flashes rapidly.
-
B While holding the “setup” button on the wireless, battery less control, briefly press the “Wake Up” or “Sleep” control on the wireless battery less control.
-
C The indicator light of the wired product will briefly turn blue, and then will turn green again. The pairing was successful.
Complete the configuration of the scenarios using your HOME + CONTROL application, menu “Settings”, then “Scenarios
Complete the installation
To complete your installation, briefly press the configuration of the
Module Control or the middle of the wireless Home / Away master
switc h or on the configuration button of the mobile gateway power outlet.
All the indicator lights on the products switch off.
| |
---|---|---
If necessary, erase the configuration of the wireless battery less control (factory reset)
While holding the “setup” button on the wireless battery less control, press
the “Wake Up” button for 5 seconds.
Confirm that your control is correctly reset by making an “Wake Up”
command, then “Sleep
Before fixing the wireless control(s) with the removable stickers provided, test one on a non-visible area of the wall.
You can also fix the wireless control(s) permanently to the wall with screws.
http://www.legrandoc.com/064884L
LEGRAND – Pro and Consumer Service
The undersigned, Legrand declares that the radio-electric equipment type (0 648 84L/85L – 0 677 86L – CB0423/CT0423/CN0423 – 0 770 57L – 6 000 84L -5 742 87/93 – 5 743 22 – 5 748 36 – 7 418 03L/33L/63L) complies with directive 2014/53/EU. The full text of the EU declaration of conformity is available on the following website: www.legrandoc.com
Download the app
Your installation is ready. You can download the Legrand Home + Contro l
application to control your lights remotely
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with FCC RF and Innovation, Science and Economic Development Canada’s licence-
exempt RSS(s). Operation is subject to the following two conditions: (1) this
device may not cause interference, and (2) This device must accept any
interference, including interference that may cause undesired operation of the
device.
This device complies with FCC and ISED radiation exposure limits set forth for
general population. This device must not be co located or operating in
conjunction with any other antenna or transmitter.
FCC Caution: the user that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
FCC NOTE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instruction, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
Safety instructions
Make sure the power supply is disconnected before any intervention. Strictly comply with instructions for installation and use.
References
- Welcome to Legrand - Legrand
- Legrand E-catalog International | Electrical Ranges of products & Connected Solutions
- legrandoc
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>