ICP DAS U-7524M CR UA I/O Series 5 Channels DO and 2 Port Ethernet Switch User Guide

June 14, 2024
ICP DAS

ICP DAS U-7524M CR UA I/O Series 5 Channels DO and 2 Port Ethernet

Switch

Packing List

UA I/O package includes this document and the following items:

ICP-DAS-U-7524M-CR-UA-I-O-Series-5-Channels-DO-and-2-Port-Ethernet-Switch
-FIG-1

Technical Resources
How to search for drivers, manuals and spec information on ICP DAS website

ICP-DAS-U-7524M-CR-UA-I-O-Series-5-Channels-DO-and-2-Port-Ethernet-Switch
-FIG-3

Preparations for Devices

  1. PC/NB: Can connect to the network and set the network
  2. Ethernet Switch/Hub (Ex: NS-205A or PoE Switch NSM-208SE)
  3. Power Supply: +12 ~ +48 VDC (Ex: MDR-60-24)

Hardware Connection

Connect the UA I/O Module with the RJ-45 Ethernet port to an Ethernet switch/hub (Fig.2 for PoE Switch) and PC. You can also directly link the U-75xx to PC with an Ethernet cable. After power is connected, please【wait 1 minute】for U-75xx  start-up procedure. When the “RUN” light starts flashing, it represents the boot is complete.

ICP-DAS-U-7524M-CR-UA-I-O-Series-5-Channels-DO-and-2-Port-Ethernet-Switch
-FIG-4

Network Connection

Factory Default Settings of U-75xx



Network

| IP| 192.168.255.1| Assign U-75xx a new IP setting according to your case.
Mask| 255.255.0.0
Gateway| 192.168.1.1
Web UI Account| Username| root| After login, change the username/ password at once.
Password| root

  • Change the PC’s IP setting as following. (Write down the PC original network settings before modify.) EX:
IP 192.168.255.10
Subnet mask 255.255.0.0
Default Gateway 192.168.1.1
  • Make sure the PC and U-75xx is connecting through Ethernet. And then open a PC side browser (Ex: Chrome, IE…). Type http://192.168.255.1 in the URL address. Use default Web UI username/password root/root to login.ICP-DAS-U-7524M-CR-UA-I-O-Series-5-Channels-DO-and-2-Port-Ethernet-Switch -FIG-5
  • Change the Username/password in 【Account Setting】of 【System Setting】, or user cannot use any other functionICP-DAS-U-7524M-CR-UA-I-O-Series-5-Channels-DO-and-2-Port-Ethernet-Switch -FIG-6
  • Click【System Setting】【Network Setting】>【Network Setting(LAN)】to change the IP settings by user networkICP-DAS-U-7524M-CR-UA-I-O-Series-5-Channels-DO-and-2-Port-Ethernet-Switch -FIG-7
  • Save the IP settings, restore the PC original IP settings, and then type the new IP/Username/Password in the browser to login the Web UI of U-75xx to configure user’s UA project

AI/AO Jumper Setting

To change the Selection Jumpers for Analog channels:

U-7528M

Channel|
Jumper|
Channel| V/Iout6+| V/Iout7+
Jumper| J1| J2

Remove the top case and upper board of the module, the selection jumpers are next to the connector.ICP-DAS-U-7524M-CR-UA-I-O-Series-5-Channels-DO-
and-2-Port-Ethernet-Switch -FIG-8

U-7502M

Channel| Vin1±| Vin0±
Jumper| J2| J1
Channel| Vin2±
Jumper| J3
U-7528M

Channel|
Jumper|
Channel| V/Iout6+| V/Iout7+
Jumper| J1| J2
U-7517M-10

Channel| Vin8±| Vin7±| Vin6±| Vin5±| Vin4±| Vin3±| Vin2±| Vin1±| Vin0±
Jumper| J9| J8| J7| J6| J5| J4| J3| J2| J1
Channel| Vin9±
Jumper| J10

Jumper Location Figure

ICP-DAS-U-7524M-CR-UA-I-O-Series-5-Channels-DO-and-2-Port-Ethernet-Switch
-FIG-9

U-7504M

Channel| Vin3| Vin2| Vin1| Vin0| Vout3| Vout2| Vout1| Vout0
Jumper| J4| J3| J2| J1| J8| J7| J6| J5
U-7524M

Channel| Vout3+| Vout2+| Vout1+| Vout0+
Jumper| J4| J3| J2| J1
U-7526M

Channel| Vout1| Vout0| Vin5| Vin4| Vin3| Vin2| Vin1| Vin0
Jumper| J8| J7| J6| J5| J4| J3| J2| J1
U-7517M

Channel| Vin7±| Vin6±| Vin5±| Vin4±| Vin3±| Vin2±| Vin1±| Vin0±
Jumper| J8| J7| J6| J5| J4| J3| J2| J1
U- 7519ZM

Channel| CH0±| CH1±| CH2±| CH3±| CH4±| CH5±| CH6±| CH7±| CH8±| CH9±
Jumper| J1| J2| J3| J4| J5| J6| J7| J8| J9| J10

  • Set up the Jumper corresponding to the type of Voltage /  Current and Input / Output for each analog channel.

Voltage Input Selection Jumper (Jumpers default: Voltage

ICP-DAS-U-7524M-CR-UA-I-O-Series-5-Channels-DO-and-2-Port-Ethernet-Switch
-FIG-10

  • Voltage Input (Single-ended Mode) Selection JumperICP-DAS-U-7524M-CR-UA-I-O-Series-5-Channels-DO-and-2-Port-Ethernet-Switch -FIG-11
  • Voltage Output Selection JumperICP-DAS-U-7524M-CR-UA-I-O-Series-5-Channels-DO-and-2-Port-Ethernet-Switch -FIG-12
  • Current Input Selection JumperICP-DAS-U-7524M-CR-UA-I-O-Series-5-Channels-DO-and-2-Port-Ethernet-Switch -FIG-13
  • Current Output Selection JumperICP-DAS-U-7524M-CR-UA-I-O-Series-5-Channels-DO-and-2-Port-Ethernet-Switch -FIG-14
  • Thermocouple Input Selection JumperICP-DAS-U-7524M-CR-UA-I-O-Series-5-Channels-DO-and-2-Port-Ethernet-Switch -FIG-15

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals