HATHEPHS CS01 Smoke Alarm and Carbon Monoxide Detector User Guide

HATHEPHS CS01 Smoke Alarm and Carbon Monoxide Detector

Thank you!

Thank you for purchasing our photoelectric smoke and carbon monoxide combination alarm device. Please read this manual carefully to ensure proper use and store it in a safe place for future reference.

Product Specifications

Power: DC 2*1.5V AA Alkaline Battery
Operation Current: <15uA (standby); <70mA (alarm)
Alarm Volume: >85 dB(A) at 3 meters
Smoke Sensitivity: 0.09 – 0.17 dB/m
CO sensitivity: 50ppm 60~90 min | 1oo ppm 10~40 min | 300 ppm <3 min
Low Battery: 2.6 ± 0.1 V
Silence Time: approx. 10 minutes
Comply to Standard 1: EN 14604:2005/ AC:2008 (for smoke detector)
Comply to Standard 2: EN 50291-1:2018(for carbon monoxide detector)

Packing List

• 1 x smoke and carbon monoxide alarm
• 1 x Mounting bracket
• 1 x Screw Kit (install option 1)
• 1 x Adhesive (install option 2)
• 1 x User manual

Product profile

Installation Instructions

Where to install

1. At first you should install an alarm in the bedroom and walkway. If there are several bedrooms in the house, please install an alarm in every bedroom.

2. Install an alarm above the stairway and on every floor of the house.

3. Smoke, heat and burning things will spread horizontally after rising to the ceiling, so install the alarm in middle of the ceiling.

4. If the alarm cannot be installed in the middle of the ceiling, install it keeping 300mm away from the corners. (see the figure 1 ).
   

5. If the alarm is installed in the wall, it should keep 100 mm away from the ceiling.

6. If the length of the room or the hall is beyond 30 foot, you need to install several alarms there.

7. When the wall or ceiling is slanting, the alarm needs to be installed minimum 500mm away from the highest wall or ceiling point in the room (see the figure 2).
   

SINGLE FLOOR PLAN

● Smoke or Smoke/CO Alarms for Required Protection
○ Smoke Alarms for Additional Protection
△ Ionization Type Smoke Alarms with ” Hush” Control or Photoelectric Type

MULTIPLE FLOOR PLAN

Locations to Avoid

1. High-humidity areas such as kitchens, and bathrooms.
2. Next to air outlets, fans, and central heating.
3. Dusty, dirty areas or areas with insects.
4. High-temperature and easily polluted places.
5. Places with difficult access, making it difficult to operate the test function.
6. Within 1.5m from lamps.
7. Next to doors or windows.
8. In the top of rooms with sloping roofs, the corner of the room or other dead-air spaces.

Mounting Alarms

1. Twist off the mounting bracket from the alarm.
2. Put the bracket on the installation position and mark the screw holes on the ceiling or the wall.
3. Drill two mounting holes in the marketplace by an electric drill (The diameter of the drill hole is 5mm) and insert two plastic anchor plugs by hammer.
4. Screw the mounting bracket to the ceiling or the wall (Refer to figure 3).
5. Attach the alarm to the mounting bracket and turn clockwise to lock the alarm.
6. If you have any question on installation, please contact your retailer.

WARNING: The installation instructions must be followed strictly in case of any injury.

How to Power up & off the device

When the battery is installed on the device, it will be powered on automatically.

Test your Alarm

Test the unit to ensure proper operation by pressing the cover, the alarm will sound if the unit are working well. If no sounds, you can refer to “Troubleshooting” section for solution.

CAUTION:

1. DD NOT test your alarm using an open flame. This may damage the smoke alarm or ignite combustible materials and start a structural fire.
2. DO NOT stand close to the alarm when the alarm is sounding. Exposure at close range may be harmful to your earing, so step away when testing.
3. Weekly Test: test this smoke alarm once a week.

LED and Buzzer Indicators

1. Normal status: Green LED Flashes once every 60 seconds.
2. Test status: Two sets of 3 long beeps with Red LED flashes and two sets of 4 quick beeps with Red LED flashes.
3. Smoke alarm: Red LED flashes 4 times synchronized with 4 long beeps.
4. Carbon monoxide alarm: Red LED flashes 3 times synchronized with 3 short beeps.
5. Hush/Silence mode: Red LED flashes once every 8 seconds.
6. Low Battery status: Red LED flashes once every 60 seconds and 1 beep every 60 seconds.
7. Fault status: the alarm will deliver beeps every 40 seconds.

Silence Mode

During the unit is alarming, you can push the test button, it will be paused the unit alarming for approx 10 minutes. The red LED will flash once every 8 seconds, it indicates the smoke alarm device is running into the silence mode.The silence feature is to be used only when a known alarm condition, such as smoke from cooking activates the alarm.The smoke alarm device will automatically reset after approximately 10 minutes, if after this period, particles of combustion are still present, the alarm will sound again.

CAUTION:
Before using the alarm silence (silence), identify the source of the smoke and be certain a safe condition exists.

Maintenance and Cleaning

There are a few simple steps you need do to keep it working properly.

1. Test the alarm once a week.
2. Clean the alarm surface with a soft brush or cloth every month.
3. Do not paint the alarm. Paint will seal the vents and interfere with the sensor’s ability to detect smoke.
4. Never attempt to disassemble the alarm to clean inside. In addition to weekly testing, the alarm requires periodic cleaning to remove dust, dirt 1 and debris.
5. Clean the alarm at least once a month to remove dust, dirt, or debris.
6. Use a vacuum cleaner with the soft brush, vacuum all sides and covers of smoke alarm device.

If there is a defective battery or other failures, you can refer to “Troubleshooting” for solution, if there are still failures during warranty, you can return to your retailer.

IMPORTANT: Do not attempt to remove the cover to clean inside. This will void warranty.

Replaced Battery

1. The low battery signal can last for maximum 30 days, please replace the batteries in time to keep it working properly.

2. Battery required: standard 2* 1.5v AA batteries.
   

3. Correctly install the positive and negative poles of the battery(+&-)

TroubleShooting

Problem

|

Method of disposal

---|---
The alarm does not sound when testing| Please check whether the batteries be well assembled according to the Guide required
Red LED flashes and the alarm delivers one beep every 60 seconds| The battery is low. Please replace the batteries as soon as possible.
The alarm delivers one beep every 40 seconds|

1. clean the alarm. Please refer to the “maintenance and cleaning” section.
2. the alarm is malfunctioning. Contact the retailer to replace it.

Nuisance alarms are triggered intermittently or when residents are cooking, taking showers, etc.|

1. press silence button.
2. clean the alarm. Please refer to the “maintenance and cleaning”
3. move the alarm to new location.

Warranty Information

Amazon usually provide 30 days warranty after you purchase items, if you want to extend 12 months, just contact us by email.
Contact email: support@aunguuk.com
During the specified warranty period, we will repair or replace, at its discretion any defective Alarms that are returned to the retailer.
Please include your name, address, and phone number along with a brief description of what is wrong with the unit.
This warranty shall not apply to the alarm if it has been damaged, modified, abused, or altered after the date of purchase or if it fails to operate due to improper maintenance.
The Manufacturer shall have no liability for any personal injury, property damage, or any special, incidental, contingent, or consequential damage of any kind resulting from gas leakage, smoke, fire, or explosion.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>