Memoking E975 Embossing Label Maker Machine User Guide
- June 14, 2024
- Memoking
Table of Contents
Memoking E975 Embossing Label Maker Machine
Product Information
The product is a label-printing machine that allows users to create and print custom labels. It features a dial for selecting different symbols and icons, a handle for printing the characters, and a slot for inserting the label tape. The machine is designed to be easy to use and provides clear and precise printing results.
Specifications
- Printing Method : Manual
- Label Tape Compatibility : Standard label tape
- Printing Area: Adjustable
- Symbols and Icons: Space, Scissors
- Power Source : Manual operation
Product Usage Instructions
Step 1: Inserting the Label Tape
- Turn the dial to move the space icon into the printing area.
- Hold the handle tightly and open the rear cover.
- Insert the label tape into the slot.
- Squeeze the handle several times to run the tape.
- Note : Do not use the scissor icon when feeding the tape to avoid accidental cuts.
Step 2: Printing the Label
- After the label tape is installed, turn the dial to select the desired characters.
- Press the handle firmly to print the characters on the label.
- After printing is completed, turn the dial until you reach the scissors icon.
- Press the handle to cut the label.
- Fold along the dotted line on the label and remove the backing.
Step 3: Replacing the Label Tape
- To replace the label tape, open the rear cover.
- Pull out the original label tape.
- Insert a new label tape following the instructions in Step 1.
FAQ
The print is not clear.
The label tape is not installed correctly. Reinstall the label tape.
The print is misaligned.
The disc is set incorrectly. Rotate the dial to align the scissors icons of
the upper and lower discs.
The disc is stuck.
The disc may be stuck due to a mechanical issue. Please contact customer
support for assistance.
The label tape is stuck.
If you are unable to remove the label tape, please contact customer support
for guidance
The label won’t print.
Ensure that the label tape is properly installed. If the issue persists,
please contact customer support for further assistance.
How to prevent tape residue from accumulating inside the machine?
Cut the tape cleanly. Open the rear lid to check the amount of adhesive
tape remaining. When there is little label tape left, replace it immediately.
Instructions
- Turn the dial and move the “ ” space icon into the print area.
- Note : Please do not use the “ ” scissor icon when feeding the tape, because you may accidentally cut the label tape if you squeeze too hard
- Note : Please do not use the “ ” scissor icon when feeding the tape, because you may accidentally cut the label tape if you squeeze too hard
- Hold the handle tightly and open the rear cover.
- Insert the label tape into the slot and squeeze the handle several times to run the tape.
- Note: When the label tape is inserted into the slot, the label tape shall be pushed up until it cannot be pushed and the hand plate shall be squeezed several times.
- After the label is installed, turn the dial and press the handle to print the characters.
- After the printing is completed, turn the disc until you reach the “ ” Scissors icon, and press the handle to cut.
- Fold along the dotted line on the label and remove the backing.
- To replace the label tape, open the rear cover, pull out the original label tape, and repeat steps ① ② ③.
Common problems and solutions
| Question/Problem | Reason | Solution |
|---|
The print is not clear.
| The handle is not pressed hard enough.| Press the handle firmly.
The label tape is not installed correctly.| Reinstall the label tape.
Incorrect printing due to poor alignment of the upper and lower discs.| Rotate
the dial to align the scissors icons
of the upper and lower discs.
The print is misaligned.| The disc is set incorrectly.| Print the
characters in the printing area.
Turning the dial too fast may cause distorted prints or ghosting.
The disc is stuck.| Pressing the handle incorrectly.| Do not press the
handle when turning the disc.
The label tape is stuck.| Do not press the handle when removing the
label tape.
The label won’t print.| Label tape is not installed.| Check if the label
tape is inserted correctly.
The output slot of the machine is clogged with label tape residue.| Use a pair
of tweezers to remove the tape residue.
How to prevent tape residue from
accumulating inside the machine.| The label tape is not cut properly and
remains inside the machine.
Do not cut it more than once. The label tape may get stuck between
the input and output slots.| 1. Cut the tape cleanly.
2. Open the rear lid to check the amount of adhesive tape remaining. When
there is little label tape left, replace it immediately.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>