Maidesite M015-00 Electric Standing Desk Instruction Manual
- June 14, 2024
- MAIDeSITe
Table of Contents
Standing Desk Assembly Instructions
*M015-00/Size:10060cm**
Safety & Warnings
Warm prompt
Make sure no obstacles are in the desk’s path. Make sure the desktop is not
touching any walls. Make sure all cords are appropriate length to accommodate
the change in height .
WARNING
Pinch Point Keep hands and fingers clear.
| Keep children away from electric height-adjustable desks, control units
and handsets. There is a risk of injury and electric shock.|
---|---|---
| Keep all electrical components away from liquids.|
| Do not sit or stand on the desk frame. Do not crawl or lie under the
desk frame.|
| Do not place any objects taller than 20″ underneath the desk.|
| Do not open any of the components – the Legs, Control Box, or Switch.
There is a danger of electric shock.|
| This product is designed with a duty cycle of 10% (2 min. on, 18 min.
off).|
| In the event of a power outage or if the power cord is unplugged, a
manual reset may be necessary – see USE section.|
USE/ LIABILITY
- This height adjustable desk has electric motors and is designed for use in dry work areas only.
- The desk height is adjustable so that it can be positioned at the most ergonomically suitable height.
- Any other use is at user’s risk.
- Under no circumstances does the manufacturer accept warranty claims or liability claims for damages caused from improper use or handling of the desk frame.
Parts List
Hardware List
STEP 1 Desktop Assembly
Note: Please make the assembly area soft and flat.
Please do not lift up the assembled desktop to avoid wood pins fracture.
![Maidesite M015 00 Electric Standing Desk
- Frame 2](https://manuals.plus/wp-content/uploads/2023/11/Maidesite-M015-00 -Electric-Standing-Desk-Frame-2.png)![Maidesite M015 00 Electric Standing Desk
- Frame 3](https://manuals.plus/wp-content/uploads/2023/11/Maidesite-M015-00 -Electric-Standing-Desk-Frame-3.png)![Maidesite M015 00 Electric Standing Desk
- Frame 4](https://manuals.plus/wp-content/uploads/2023/11/Maidesite-M015-00 -Electric-Standing-Desk-Frame-4.png)
Install the Accessories
Install the Casters
Install the Felt Side Storage Bag
Install the Memory Board
Hand Controller Instruction
CAUTION
Please RESET the desk at first time.
Please ensure that no objects (walls) will interrupt the movement of the desk,
and all cables of relevant devices are sufficiently long.
RESET: Long press the down key until the desktop reaches the lowest position;
long press the down key again, when it shows”RST ”on the digital display, the
desk is in initialization mode. Release the down key when the buzzer rings,
the initialization succeeds.
PS. If the system is abnormal or the digital display shows”RST ”, the desk
needs to be initialized as written above.
The following steps can be set according to personal preference.
Memory Height
Press the“m” key until it displays “ S – ”; press one of the memory
keys(number keys) and the current height will be recorded.
Switch between Centimeter and Inch
Long press the“m” key for 5 seconds until it displays “S-1”and “1”flashes.
Press the“m”key again to set:
0 = cm
1 = inches
Exit to operation interface by pressing the“m”key after setting.
The following steps can be set according to personal preference.
Anti-collision Sensitivity
1 “S-3”anti-collision sensitivity while going up Long press the“m”key for 5
seconds until it displays “S-1”and “1”flashes. Press the“up”key to switch
to“S-3”; press the“m”key to set up sensitivity :
0= Closed
1=Minimum Sensitivity
…… 8=Maximum Sensitivity
Exit to operation interface by pressing the“m”key after setting.
2 “S-4”anti-collision sensitivity while going down
Long press the“m”key for 5 seconds until it displays “S-1”. Press the“up”key
to switch to“S-4”; press the“m”key to set up sensitivity :
0= Closed
1=Minimum Sensitivity
…… 8= Maximum Sensitivity Exit to operation interface by pressing the“m”key
after setting.
Switch between Jog and Continuation at Memory Height
Long press the“m”key for 5 seconds until it displays “S-1”and “1”flashes.
Press the“up”key to switch to“S-6”; press the“m”key to set:
0=Jog (Long press a memory key 1/2/3/4, and it will stop after release)
1=Continuation (Press a memory key 1/2/3/4, and it will goes to default height
automatically)
Exit to operation interface by pressing the“m”key after setting.
Lock & Unlock
Lock: Press both the “m” and “up” keys for 5 seconds, when it displays”LOC”,
the system is locked and the desk can’t go up or down. Unlock: Press both
the“m” and “down” keys for 5 seconds, when it displays a number, the system is
unlocked.
Factory Initialization
If a new desk frame is replaced or to initialization default data; press both
the“up” and “down” keys for 10 seconds, the system is initialization to
default data after the buzzer rings once again, and it will display“RST” ; the
system is restored to its original settings.
The following steps can be set according to personal preference.
Max. Height Limit 96cm-120cm)
Adjust the desk to the target Max. height limit; press both the“up” and “down”
keys for 5 seconds; the height limit is restored after the buzzer rings.
Min. Height Limit (72cm-96cm)
Adjust the desk to the target Min. height limit; press both the“up” and “down”
keys for 5 seconds; the height limit is restored after the buzzer rings.
Cancel the Height Limit
RESET: the desk and the height limits will be auto-canceled.
USB Port
Output Voltage: 5V
Output Current: 0.8A
Error Codes & Solution
Error Code | Description | Solution |
---|---|---|
0.00E+00 | The voltage of the main power supply is over 45V. | Check the main |
power supply.
0.00E+00| The height difference is over 1 an between lead screws.|
Initialization.
0.00E+00| Something is wrong with the controller in connecting or working.|
Check the wire of the controller.
0.00E+00| The desk is blocked and stopped.| Release the key and run it again.
0.00E+00| Failed in powering up and the voltage is under 20V.| Replace the
main power supply or check the wire of it.
0.00E+00| It is protected while the main power supply is working. the voltage
is under 20V.| Power on again.
0.00E+00| The desktop is tilting.| Initialization.
HOT| The temperature of the power supply is too high.
or it continues wctkilg for over 2 minutes in 18 minutes.| Wait for the power
supply to cold down or
wait for over 18 minutes before working ago,.
Ell| The motor is not connected.| Check the connecting wire.
0.00E+00| Something is wrong with the sample channel of the motor.| Replace
the control board.
0.00E+00| The wire inside the motor fails in connecting.| Check the connection
of the motor Line.
| Something is wrong with the motor Hall, a it is disconnected.| Check the
Hall signal or replace the connecting wire.
0.00E+00| Short circuit inside the motor.| Replace the motor.
0.00E+00| Locked-rotor motor.| Initialization.
Ell| The motor is rotating in the wrong direction.| Replace the motor wire or
Hall wire.
0.00E+00| The motor overloads.| Reduce the load.
0.00E+00| Control box is offline in series connection.| Check the connecting
wire.
0.00E+00| Wrong signal in series connection.| Check the connecting wire or
replace the control box.
0.00E+00| Something is wrong with the memory unit.| Replace the control box.
0.00E+00| Something is wrong with the anti-collision sensor.| Replace the
control box.
** MADE IN CHINA
Prolinx Global LTD
27 Old Gloucester Street
London,WC1N 3AX,UK
Mr.Nianzhuang Liu
Email: eu@eulinx.eu
Email(UK): Customerservice-EU@maidesite.com
Instagra
Website: www.maidesite.co.uk**
YouTube:Maidesite Office
Facebook:Maidesite Desk
m Maidesite Standing Desk
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>