Oase EAC0012 Aquarium Controller Instruction Manual
- June 14, 2024
- Oase
Table of Contents
Oase EAC0012 Aquarium Controller
Commissioning
Original manual. This manual belongs to the unit and must always be passed on together with the unit.
WARNING
- Switch off all units in the aquarium or disconnect the power plugs of all units before reaching into the water.
- This unit can be used by children aged 8 and above and by persons with reduced physical, sensory, or mental capabilities or lack of experience and knowledge if they are supervised or have been instructed on how to use the unit safely and they understand the hazards involved. Do not allow children to play with the unit. Only allow children to carry out cleaning and user maintenance under supervision.
Further instructions in a PDF format are available for download online at: www.oase.com/manual
The following additional topics are addressed in the operating manual:
- Symbols on the unit
- Updating the firmware
- Cleaning and maintenance, malfunction rectification
- Technical data
- Disposal
Safety information
Electrical connection
- Only connect the unit if the electrical data of the unit and the power supply match.
- Only plug the unit into a correctly installed outlet.
- The device is to be supplied through a residual current device (RCD) having a rated residual operating current not exceeding 30 mA.
- Protect open plugs and sockets from moisture.
Safe operation
- Never immerse the unit in water or other liquids.
- Do not use the unit, if electrical lines or the housing are damaged.
- Do not carry or pull the unit by its power cable.
- Route lines in such a way that they are protected from damage and do not present a tripping hazard.
- Only carry out work on the unit that is described in this manual.
- Never carry out technical changes to the unit.
- Only use original spare parts and accessories.
- Should problems occur, please contact the authorized customer service or OASE.
Intended use
Only use the product described in this manual as follows:
- For controlling and monitoring OASE Control-compatible devices from the aquarium-keeping segment.
- Indoors only.
- While adhering to the technical specifications.
The following restrictions apply to the unit:
- Do not use for commercial or industrial purposes.
Product Description
- The Aquarium Controller is a control system for electrical equipment with OASE Control functions from the aquarium-keeping segment. It is operated using the free app “OASE Control” for tablets or smartphones.
- The Cloud function makes it possible to use the Aquarium Controller outside of the home network via OASE Cloud.
- More information about the App and the OASE Control-system is available at www.oase.com.
System Overview
System components, accessories
Aquarium Controller
(33885)
| For controlling electrical equipment with OASE Control function-
options from the aquarium-keeping segment.
---|---
OASE Control Aquarium Transformer 120 W (INT: 33888, GB: 33889)| For supplying
the Controller and end devices with power.
Highline Premium LED Power Adapter (33898)| For connecting end devices with
increased power consumption that require an additional OASE Control Aquarium
Trans- former 120 W.
OASE Control Aquarium Y-Adapter (33897)| For connecting two end devices to one
Controller output.
Stream Max Pump Controller (33919)| For controlling flow pumps with the
Aquarium Controller.
System configuration
-
The maximum permissible power consumption of the system is limited by the maximum output of the power supply. (See type plate or operating manual for OASE Control Aquarium Transformer 120 W)
Example: The maximum output of the OASE Control Aquarium Transformer is 120 W. This means the total maximum power consumptions of all connected devices (end devices plus Controller) must not exceed 120 W. (See type plate or operating manual for the connected device.) -
If you would like to connect end devices with greater power consumption to a Controller out-put, use a HighLine Premium LED Power Adapter and an additional OASE Control Aquarium Transformer 120 W. This transformer will then exclusively supply the end device connected to it.
Product Overview
- Connection OASE Control Aquarium Transformer
- Connection for a device with OASE Control functions from the aquarium-keeping segment.
- Status LED (→ Operating conditions indicated by the Status LED)
- Service button (→ Service button functions)
Operating conditions indicated by the Status LED
| LED | LED status | Description |
|---|---|---|
| – | Off | The Aquarium Controller is switched off. |
| Green | Lit | A direct connection is established. |
| Flashing slowly (1× per second) | A connection to a WiFi network is |
established.
Yellow| Lit| The Aquarium Controller is starting.
| Flashing slowly (2 s on, 1 s off)| The Aquarium Controller is attempting to
establish a connection to the router. This can take several minutes.
· If no connection is found, check the WiFi connection. If necessary, reduce the distance between the Aquarium Controller and the router.
Green+ yellow| Lit| The Aquarium Controller is in firmware update mode.
| Green is lit, yellow is flashing| A firmware update is in progress.
Red| Flashing| An internal error has occurred; recommended procedure:
· Disconnect the power supply, and wait for approx. 10 seconds, then re- establish the power supply.
· If the error remains active, …
– use the “OASE Control” app to check for new firmware. If necessary, install new firmware.
– reset the device to its factory settings and restart it. (→ Service button functions)
– contact the OASE service.
Service button functions
| Operation | Description |
|---|---|
| Press and hold for 5 seconds until the green LED begins to flash. | Reset |
network settings.
· When the button is released, the green LED extinguishes, and the yellow LED lights up for approx. 5 seconds. Then the yellow LED extinguishes and the green LED lights up.
· The network settings are reset to the delivery default settings.
· All other settings are maintained (e.g. device list and device settings).
Press and hold for 15 seconds until the yellow LED begins to flash.| Reset to factory settings.
· When the button is released, the green LED extinguishes, and the yellow LED lights up for approximately. 10 seconds. Then the yellow LED extinguishes and the green LED lights up.
· All settings are reset to the delivery default settings.
Installation
Place the Aquarium Controller in a protected, dry location, for example in the cabinet below an OASE aquarium.
Connection
Connect the system as shown in the system overview. (→ System overview)
- Establishing the plug connection
- Disconnecting the plug connection
Commissioning/start-up
Switching ON/OFF
- Switching on: Establish the power supply.
- Switching off: Disconnect from the power supply.
Installing the “OASE Control” app
The “OASE Control” App must be installed on your Smartphone/tablet for
commissioning and operating the unit.
The operating systems iOS 12.0 (Apple) or Android 7.0 or newer are required to
operate the App on mobile devices.
How to proceed:
- Install the App “OASE Control” via the App Store of your operating system (iOS or Android).
- Open the App “OASE Control” and follow the instructions.
- When you first open the App, you will be asked to create your own free OASE account. The account allows you to easily use multiple smart devices. All settings are automatically synchronized via your account.
Establishing a connection
For operation, the Aquarium Controller and the Smartphone/Tablet must be
connected via a WiFi network. a
| Connection type | Description |
|---|---|
| WiFi network connection (Standard) | The Aquarium Controller establishes a |
wireless connection to a WiFi network router.
· To use the Cloud functions, the network router must be connected to the internet.
Direct connection (Ad-hoc connection)| Only recommended if no WiFi network router signal is available at the in- installation site.
The Aquarium Controller creates its WiFi network (SSID and password see type plate). Please note:
· The Aquarium Controller can only be operated with the aid of a mobile device (smartphone/tablet) if the mobile device is connected to its WiFi network.
· As there is no internet access, Cloud functions will not be available.
· Most mobile devices will automatically switch to the new WiFi network if they detect a known WiFi network with internet access.
WiFi network connection(Standard)
Direct connection (Ad-hoc connection)
OASE GmbH
- Address: Tecklenburger Straße 161 48477 Hörstel | Germany
- + 49 (0) 5454 80-0
- + 49 (0) 5454 80-9353
- info@oase.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>