JUNLIT B09HK4892L Mini Smart Plug Smart Outlet Instructions
- June 14, 2024
- junlit
Table of Contents
- Product Instruction
- Indicator Light Status
- Safety Information
- Installation
- Add Devices
- Set your Echo Speaker by Alexa APP
- Enable Smart Life Skill in Alexa APP
- Control the Light Switch by Voice
- Google Assistant-Activate Smart Life in Google Home APP
- Specification
- Troubleshooting Guide
- Warranty
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
JUNLIT B09HK4892L Mini Smart Plug Smart Outlet Instructions
Product Instruction
Control Devices From anywhere Using the Smart life APP
Indicator Light Status
Light Status | Switch Status |
---|---|
ON | Power OFF |
OFF | Power ON |
Steady on | Energy-saving mode |
Blink quickly (0.3s interval) | Ready for default con -figuration mode |
Blink slowly [1.5s interval] | Ready for AP(Access Point) configuration mode |
Turn on for 10s and then turns off | Configured successfully but the network |
dis-connects suddenly
Safety Information
Risk of Electric Shock: Electricity can cause personal injury and
property damage if handled improperly. If you are not sure about any part of
these instructions, please seek professional assistance from a qualified
electrician.
Warnings
- Turn off the power at the circuit breaker and test that power is off before wiring
- Check supported maximum wattage rating: 1250W.
- Prepare Other Tools You’ll Need
- Screwdriver
- Plier
- Electrical Tester
Installation
Note
-
Make sure that the power at the circuit breaker is off before wiring.
-
Neutral Wire is required. Confirm the wall box containsa Neutral Wire (typically white). If the wall box don’t have
a Neutral Wire, please try another location in your home or call a professional electrician to in stall the switch. -
The wire colors indicated in this manual are the usual colors and may differ in some homes.
-
Ensure the wire conductors are securely fastened to each wire.
-
If you don’t have any wiring experience, please call a professional electrician.
STEP 1
Turn off the circuit breaker and use the electrical tester to test the
power. Ensure the switch is off before wiring.
STEP 2
Remove the existing wall plate; Turn on the power at the circuit breaker and
use an electrical tester to check which wire is line/load wire; The tester
will flash and/ or chirp when it comes close to a load/line wire.
Turn off the power at the circuit breaker and use the electric tester to test
if the power is off, and then pull the existing switch out; Label the
line/load wire and other wires; Disconnect the wires from the existing switch
with plier.
Follow the wiring diagram to connect the switch wires to the wires in the wall
box with the wire conductors.
STEP 3
Mount the switch with the provided screws and sna the wall plate on it.
STEP 4
Turn the power back on at the circuit breaker.
STEP 5
Switch the light on.
Add Devices
-
Download Smart Life APP
Please scan the QR code or download Smart Life on APP Store or Google Play. -
Registration or Log In
- Download Smart Life Application.
- Enter the Register/Login interface: Tap “Register” to create an account by entering your phone number to get.
- Verification code and “Set pass-word”. Choose “Login” if you already have a Smart Life account. 3
-
Configure the APP to the Switch
Preparation: Ensure the switch has connected with electricity: Ensure your phone has connected to Wi-Fi router and is able to connect to the internet.
Note: This switch only supports 2.4G network. If you have connected 5G network, please disconnect 5G network firstly.
Tap the icon “+” on the top right corner to Select Device Type-tap “all” and choose “Wall Switch” -
Default Configuration Mode
* Press and hold the manual switch for 5 seconds until the blue indicator light blinks quickly.
* Tap “Confirm indicator rapidly blink”: Enter WiFi Password:Wait for completing the connection.
*Note: You can search the devices via Bluetooth.
* Devices have added successfully; If you can only find one switch, please start the above steps to configure the other switch again.
2. AP Mode
* If you cannot configure successfully with the default. mode, please try to connect with AP Mode
* Tap “AP Mode” on the top right corner.
* Press and hold the manual switch for 5 seconds, you can see the blue indicator light blinks quickly. Then press and hold for 3s again until the indicator light blinks slowly.
* Tap “Confirm indicator slowly blink”
* Enter WiFi Password.
* Open WLAN settings; Connect witch “Smart Life -xxxx”.
* Back to the APP and continue to add the device and wait for completing the connection
Set your Echo Speaker by Alexa APP
-
If you have finished to install Smart Life then open Amazon Alexa App: Sign in your Alexa account and enter password.
-
Click the menu on the left corner-click “Settings”; Choose “Set up a new device” Ichoose a device, like Echol Note: When the below page appears, long press the small dot on your Echo device until the light turns to yellow. Then click Continue on App.
Note: At this moment, the mobile phone can not open a variety of VPN software.
-
Choose your own WIFI and wait for a few minutes. After an introduction video, click next step, it will enter Home page automatically. Now the Echo has connected to WIFI successfully
Enable Smart Life Skill in Alexa APP
Choose “Skills” in the options bar, and then searck “Smart Life” in the input box.
Select Smart Life in the search results, and then click “Enable Skill”.
Then input the user name and password of Smart Life APP that you had
previously registered.
Control the Light Switch by Voice
After the above operation is successful, you can control the Light Switch via Echo.
-
Discover Devices
Firstly, you need to say to the Echo:
“Echo (or Alexa), discover my devices,”
Echo will start to find the device which is added in Smart Life APP. It will take about 20 seconds, then Echo will tell you the result.
You can also click “Discover devices in Alexa APP, then it will show the devices that have been found successfully.
-
Control Device by Voice Note:
The name of the device must be consistent with the addition of Smart Life APP. ntrol You can also group the Light Switch and give instructions to control them together.
Note:
Echo is one of the wake-up names, which can be any of the three names [Settings]: Alexa, Echo, Amazon. -
Support Skill List
You can control the device by instructions like these: “Alexa (or Echol, turn on the Light Switch” “Alexa (or Echo), turn off the Light Switch
Google Assistant-Activate Smart Life in Google Home APP
Preparation
- Have downloaded the Google Home App
- compatible with Android (4.2 or higher] or IOS (8.0 or higher] smartphones or tablet.
- Have registered your Google Account
- Have paired Light Switch with Smart Life APP and named it with a recognizable name.
- Have finished setting up Google Home.
STEP 1
Open Google Home App: Tap” “on the upper left corner; Select “More
Settings” to enter the next interface.
STEP 2
Choose “Services” in the options bar and select “Smart Life” to enter next
interface.
STEP 3
Tap “Link Account”, then sign in your Smart Life Account.
STEP 4
Tap Link Now, after your Smart Life account has linked to Google Assistant,
the smart devices will automatically appear. Command the Device through Your
Voice After the above operation is successful, you can control the device via
Google Home. Firstly, you need to say “OK Google, talk to Smart Life” to wake
up the Smart Life. Then you can control the device by instructions like these:
“Turn on the Light Switch “Turn off the Light Switch”
Note
After Smart Life has been wakened up, you can say “Cancel” or “Stop” to exit
Smart Life or say “Nothing” when you hear “What can I do for you”. Then you
can say “OK Google, talk to Smart Life” to start voice control.
Specification
Model | YSS101 |
---|---|
Input Voltage | 120V-60Hz |
Output Current | 10A |
Supported Bulb Types | Dimmable LEO – 300WIncandescent – 600W |
Wireless Frequency | 2,46 |
Wireless Standard | IEEE802.11 b/g/n |
Support System | Android 4,4 and above orIDS 10.0 and above |
Operating Temperature | 512-45t |
Working Humidity | 35%,-85% RH |
Troubleshooting Guide
Possible Problem | Possible Cause | Solution |
---|---|---|
1.1nableto connect the switch with the phone | The switch is not al | |
– [awed for connection or the switch has been connected | **Press and hold |
the switch for 3s, the switch will initiate configuration
Unable to turn tht switch on/oft manually| ncorrect wiring| Make sure the
switch is wired correctly
No electricity| Check the circuit breaker: Make sure that the power is
restored to the switch
The light bulb is broken or is not compatible| Replace the light bulb
The switch won’t respond to APP control| Network delays or is
disconnected| Check your network connectivity
Permission is denied by your phone| Grant permission on your
phone Settings
The switch is out of order| Manually switch on
to check the switch
Your light bulb is blinking when switched off| Electric leakage occurs
or the light bulb and the switch are not compatible| Rewire or replace the
light bulb
The switch can’t connect to the APP| Enter wrong WiFi
pass-word| Enter the correct WiFi password
Weak WiFi signal| Check WiFi signal
Unable to connect to WiFi| Confirm Your WiFi is** 2.40
Warranty
This product carries a one-year warranty from purchase date. Please feel free
to let us know what we can do to assist you when you have any product problem.
Junlit customer service Email address:
supports@junlit.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>