Enerlites HMVS-J Series 180° PIR Vac Motion Sensor Wall Switch Instruction Manual
- June 14, 2024
- ENERLITES
Table of Contents
Enerlites HMVS-J Series 180° PIR Vac Motion Sensor Wall Switch
Product Information
- The HMVS-J Vacancy Only Sensor Switch uses an advanced passive infrared sensor to detect heat emitted motion. It is designed to turn on a load when the manual button is pushed and will keep it on as long as it detects motion. The switch automatically shuts off the load at the end of the selected time delay, with the countdown starting after the last motion detected. The sensor is equipped with a switch to adjust the time delay.
- The coverage of the sensor includes a detection range of up to 12 feet on each side and up to 30 feet from the front. The recommended installation height for the switch is between 4 and 5 feet.
Installation Instructions
- Turn off the POWER at the circuit breaker before installing the sensor.
- Read and understand the instructions before installing. This device should be installed in accordance with the National Electric Code and local regulations. It is recommended to have a qualified electrician perform the installation.
- Ensure that the circuit breaker or fuse(s) are turned off and that power is off before wiring the device.
- Use copper wires only for wiring.
Wiring Directions
- Connect the RED wire from the sensor to the LOAD wire.
- Connect the BLACK wire from the sensor to the HOT wire.
- Connect the GREEN wire from the sensor to the GROUND wire.
Note : A NEUTRAL wire is not required for the switch.
Color Change
The face cover of the sensor is changeable. To change out the cover:
- Slide down the top cover to release it.
- Line up the tabs and slide up to attach the new cover.
Time Switch
Located on the left side of the sensor, this switch adjusts the time delay. The default position is 15 seconds (Test mode). It is selectable between Test (15secs), 10mins, and 20mins.
Manual ON/OFF Button
The push button can be used to manually turn ON/OFF the load. The load will turn ON only when the push button is used and automatically turns OFF when the selected time delay has expired. If the time delay has expired and the load turns OFF, it will turn ON again automatically if motion is detected within 30 seconds.
Warranty Information
For warranty information and further details, please visit www.enerlites.com
SPECIFICATIONS
- Voltage…………………………………………………………………………120/277VAC,60Hz
- Resistive……………………………………………………………………………………………..5A
- Incandescent………………………………………………………………………………..500W
- Electronic Ballast…………………………………..500VA@120VAC, 1000VA@277VAC
- Motor………………………………………………………………………………………..……1/8Hp
- Time Delay……………………………………………………………..15Sec, 10Mins, 20Mins
- Default Light Level………………………………………………………………30 Lux–Daylight
- Operation Temperature………………………………………………………….32° F–131° F
- Max Coverage………………………………………………………………………………..700SF
DESCRIPTION
The HMVS-J uses an advanced passive infrared sensor to detect heat-emitted motion. The sensor switch will turn on a load when the manual button is pushed and the sensor will keep it on as long as it detects motion. It will automatically shut off the load at the end of the selected time delay. The countdown of the time delay starts after the last motion detected. The sensor is also equipped with a switch to adjust Time Delay.
COVERAGE
As illustrated in Figure 1, The HMVS-J has a 180° detection range with a maximum distance of 30’ detection in front of the sensor and 12′ on the sides providing 700 sq. ft. of coverage. For maximum results, the sensor must be properly installed between the height of 4’ to 5’ and away from obstructions such as walls, furniture and transparent barriers like Low-E glass
WARNING
- Turn the POWER OFF at the circuit breaker before installing the sensor
- Read and understand these instructions before installing. This device is intended for installation in accordance with the National Electric Code and local regulations. It is recommended that a qualified electrician performs this installation. Make sure to turn off the circuit breaker or fuse(s) and make sure power is off before wiring the device.
- Use copper wires only
WIRING DIRECTIONS
- Connect RED wire from sensor to the LOAD wire.
- Connect BLACK wire from sensor to the HOT wire.
- Connect GREEN wire from sensor to the GROUND wire.
NEUTRAL wire NOT REQUIRED for switch.
COLOR CHANGE
The face cover of the sensor is changeable. To change out the cover
- Slide down top cover to release
- Line up tabs and slide up to attach
Time switch
Located on the left, this switch adjusts the time delay. Default position: 15
Seconds (Test mode) Selectable: Test (15secs), 10mins, 20mins.
Manual ON/OFF Button
The push button may be used to manually turn ON/ OFF the load. The Load will turn ON ONLY when the push button is used and automatically turns OFF when the selected time delay has expired. If the time delay has expired and the Load turns OFF, the Load will turn ON again automatically if motion is detected within 30 seconds.
WARRANTY INFORMATION
This device is warranted to be free of material and workmanship defects for 2 years from the date of purchase. Original receipt or proof of purchase from an authorized retailer must be presented upon warranty claim. ALL claims must be verified and approved by Enerlites, Inc. Warranties from other Enerlites products may vary. This warranty is nontransferable and does not cover normal wear and tear or any malfunction, failure, or defect resulting from misuse, abuse, neglect, alteration, modification, or improper installation. To the fullest extent permitted by the applicable state law, Enerlites shall not be liable to the purchaser or end user customer of Enerlites products for direct, indirect, incidental, or consequential damages even if Enerlites has been advised of the possibility of such damages. Enerlites’ total liability under this or any other warranty, express or implied, is limited to repair, replacement or refund. Repair, replacement or refund are the sole and exclusive remedies for breach of warranty or any other legal theory.
© 2021 Enerlites Inc. CA, U.S.A.
WWW.ENERLITES.COM
0211180132-01 REV 20230802
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>