Enerlites 8882 Two Gang Recessed Voltage Cable Wall Plate Instruction Manual
- June 14, 2024
- ENERLITES
Table of Contents
Enerlites 8882 Two Gang Recessed Voltage Cable Wall Plate
Product Information
The 8882 2 Gang Recessed Multimedia Pull Box cover is a wall plate designed to install low voltage cables behind your flat panel TV, amplifier, or other audio and video devices. It is compatible with a low voltage mounting bracket (sold separately). The plate can be installed with the opening facing up or down, giving your in-wall low-voltage cable installation a professional appearance.
- Specifications
- Adapter material: Thermoplastic
- Number of Gangs: 2
- Wall Plate Configuration: Audio and Video
- Opening Approximately: 2 3/4″ W x 2 3/4″ H
- Features
- Recessed design for a clean and professional look
- Compatible with low voltage mounting bracket
- Can be installed with the opening facing up or down
Product Usage Instructions
- Select a suitable location on the wall where you want to install the 2 Gang Recessed Multimedia Pull Box cover.
- If required, install a low voltage mounting bracket on the wall according to the manufacturer’s instructions.
- Ensure that the power to the area is turned off before proceeding with the installation.
- Hold the 2 Gang Recessed Multimedia Pull Box cover against the wall, aligning it with the low voltage mounting bracket if present.
- Mark the screw hole locations on the wall using a pencil.
- Drill pilot holes at the marked locations to facilitate screw installation.
- Securely fasten the 2 Gang Recessed Multimedia Pull Box cover to the wall using appropriate screws or fasteners.
- If necessary, connect your low voltage cables to the wall plate following the cable manufacturer’s instructions.
- Verify that all connections are secure and properly insulated.
- If desired, attach a multimedia device, such as a flat panel TV or amplifier, to the wall plate using suitable mounting hardware.
- Turn on the power and test the functionality of your audio and video devices.
DESCRIPTION
- 2-Gang Recessed Cable Wall Plate is used to install low voltage cables behind your flat panel TV, your amplifier or other audio and video devices.
- This plate is designed to be used with a low voltage mounting bracket (sold separately). The plate can be installed with the opening facing up or down.
- Give your in-wall low-voltage cable installation a professional appearance using this 2-Gang Recessed Low Voltage Cable Wall Plate from Enerlites
SPECIFICATIONS AND FEATURES
SPECIFICATIONS
- Adapter material ………………………………………………………………………….Thermoplastic
- Number of Gangs …………………………………………………………………………………………..2
- Wall Plate Configuration ……………………………………………………………Audio and Video
- Opening Approximately ………………………………………………………..2 3/4″ W x 2 3/4″ H
FEATURES
- Designed for use with low voltage cables behind flat screen TVs, amplifiers or other audio and video devices
- Easily holds up to 10 cables
- Mounts to a standard low voltage mounting bracket (not included)
- Can be installed with the opening facing up or down
- Screws included
INSTALLATION
- After installing a low voltage mounting bracket (not included), pass your low voltage A/V cables through the opening in the plate.
- Secure the Recessed Cable Plate to the bracket using the included screws and a Phillips head screwdriver.
WARRANTY INFORMATION
This device is warranted to be free of material and workmanship defects for 1 year from the date of purchase. Original receipt or proof of purchase from an authorized retailer must be presented upon warranty claim. ALL claims must be verified and approved by Enerlites, Inc.Warranties from other Enerlites products may vary. This warranty is nontransferable and doesnot cover normal wear and tear or any malfunction, failure, or defect resulting from misuse, abuse, neglect, alteration, modification, or improper installation.
To the fullest extent permitted by the applicable state law, Enerlites shall not be liable to the purchaser or end user customer of Enerlites products for direct, indirect, incidental, or consequential damages even if Enerlites has been advised of the possibility of such damages. Enerlites’ total liability under this or any other warranty, express or implied, is limited to repair, replacement or refund. Repair, replacement or refund are the sole and exclusive remedies for breach of warranty or any other legal theory.
© 2018 Enerlites Inc.
CA, U.S.A.
WWW.ENERLITES.COM
0206050122
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>