Enerlites WF3K 3 Way Aux Switch Dimmer and ON OFF Switch Instruction Manual
- June 14, 2024
- ENERLITES
Table of Contents
Enerlites WF3K 3 Way Aux Switch Dimmer and ON OFF Switch
FEATURES
- Requires an Enerwave WF500D Wi-Fi Dimmer switch, not a standalone switch
- Offers Three or Four-Way control with full dimming rage when used with the Enerwave WF500D WiFi Dimmer Switch
- Includes white, light almond, and black interchangeable face covers that will match most standard wall plates
- Requires in-wall installation with hard-wired connections – Neutral wire is required.
SPECIFICATIONS
- Voltage ……………………………………………………………………………….120VAC, 60Hz
- Operating Temperature ………………………………………………….32°-104°F (0°-40°C)
REQUIREMENTS
- Requires an Enerwave WF500D Wi-Fi Dimmer Switch. This is NOT a standalone switch.
- Neutral wire is required
WARNING
Turn the POWER OFF at the circuit breaker before installing the Smart Dimmer
Read and understand these instructions before installing. This device is
intended for installation by the National Electric Code and local regulations.
It is recommended that a qualified electrician perform this installation. Use
copper wire only Only Use Wires with a Minimum Temperature Rating 75°C (167°F)
WIRING DIRECTIONS
First, find out if you will be controlling the lights from one location or multiple locations. Next, identify all the wires. Once you’ve identified the wires, follow the diagram below for wiring.
COMMON 3-WAY WIRING
- Step 1. Identify all your wires (DIAGRAM 1). Label the wires or draw a diagram of existing wires
- Step 2. Convert the TRAVELER B wire to the LOAD wire. To do so, take the LOAD wire and TRAVELER B wires off SWITCH 1 and connect them with a wire cap (DIAGRAM 2)
- Step 3. Connect the other end of the TRAVELER B wire to the LOAD terminal on the WF500D
- Step 4. Connect the NEUTRAL wire to both switches
- Step 5. Connect the TRAVELER A wire from the WF500D to one of the terminals on the 3-way switch
- Step 6. Connect the HOT wire to the HOT terminal on the WF500D
- Step 7. Connect the GROUND wires to the GROUND terminals on both switches
RETROFIT WIRING with WF3K
UPGRADING STANDARD 3-WAY SWITCHES TO Wi-Fi
UPGRADING STANDARD 3-WAY Circuit
REPLACING EXISTING SWITCHES WITH WF3K and WF500D Wi-fi Dimmer
The term “3-way circuit” refers to a circuit with two switches and one load
(light) as you find at the top and bottom of a stairway. There are many ways
to physically wire a 3-way circuit so it is important to understand how the
circuit is wired before performing the upgrade to a Wi-Fi control. DIAGRAM 1
illustrates a common 3-way circuit. In Diagram 1 and Diagram 2, SWITCH ONE is
replaced with the WF3K and SWITCH TWO is replaced with the WF500D. The
auxiliary switch (WF3K) does not control the power; instead, it sends a
momentary voltage signal through the traveller wire to the primary Wi-Fi
Dimmer switch (WF500D) which in turn, controls the power to the load.
WARRANTY INFORMATION
This device is warranted to be free of material and workmanship defects for 2 years from the date of purchase. An original receipt or proof of purchase from an authorized retailer must be presented upon warranty claim. ALL claims must be verified and approved by Enerwave, Inc. Warranties from other Enerwave products may vary. This warranty is non-transferable and does not cover normal wear and tear or any malfunction, failure, or defect resulting from misuse, abuse, neglect, alteration, modification, or improper installation. To the fullest extent permitted by the applicable state law, Enerwave shall not be liable to the purchaser or end-user customer of Enerwave products for direct, indirect, incidental, or consequential damages even if Enerwave has been advised of the possibility of such damages. Enerwave’s total liability under this or any other warranty, express or implied, is limited to repair, replacement or refund. Repair, replacement or refund are the sole and exclusive remedies for breach of warranty or any other legal theory.
2019 Enerwave Home Automation WWW.ENERLITES.COM 0206190144 REV 20230802
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>