Enerlites 975547-C Single Gang Floor Box with 20A Single Tamper Resistant Receptacle Instruction Manual

: June 14, 2024
: ENERLITES

Table of Contents

Enerlites 975547-C Single Gang Floor Box with 20A Single Tamper Resistant
Product Information
Product Usage Instructions
SPECIFICATIONS
DIMENSIONS
FLOOR BOX INSTALLATION
WIRING DIRECTIONS
WARRANTY INFORMATION
CONTACT
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Enerlites 975547-C Single Gang Floor Box with 20A Single Tamper Resistant

Receptacle

Product Information

Product Name| Single Gang Floor Box with 20A Single Tamper Resistant
Receptacle
---|---
Model Numbers| 975547-C & 975547-SS
Dimensions| Box: 4-1/4″(107.2mm) x 3-1/4″(83.3mm) x 3-5/16″(83.5mm)
Cover Plate: 3″(76.2mm) x 5″(127mm)
Gasket: 3-1/2″(88.9mm) x 5/8″(15.6mm)
Receptacle: 1-13/16″(46.0mm) x 1-1/8″(28.7mm)
Description/Features| Included is a one-gang floor box with a tamper-resistant 20 amp
single receptacle, FB-06 box, gasket, and cover.
Warranty| This device is warranted to be free of material and workmanship
defects for 2 years from the date of purchase. Original receipt or
proof of purchase from an authorized retailer must be presented
upon warranty claim. This warranty is non-transferable and does not
cover normal wear and tear or any malfunction, failure, or defect
resulting from misuse, abuse, neglect, alteration, modification, or
improper installation.

Product Usage Instructions

Before Installation:
- Ensure there is sufficient depth & space below the sub-floor.
Step 1:
- For carpeted floors, cut out a section of carpet smaller than the size of the cover.
WARNING:
- Turn the POWER OFF at the circuit breaker before installing the Floor Box.
- Read and understand these instructions before installing.
- This device is intended for installation by the National Electric Code and local regulations.
- It is recommended that a qualified electrician perform this installation.
- Make sure to turn off the circuit breaker or fuse(s) and make sure the power is off before wiring the device. Use copper wire only.
NOTES:
- 10-12 AWG Stranded or Solid Copper wire is recommended.
Step 2:
- Rout 3/8″(10.16mm) Deep For Outer Tabs
Wiring Directions:
- Connect the HOT wire to the BLACK wire.
- Connect the NEUTRAL wire to the WHITE wire.
- Connect the GROUND wire to the GREEN wire.

SPECIFICATIONS

Cover Material

975547………………………………………………………………………………..Brass(C) or Stainless Steel(SS)
Receptacle Rating…………………………………………………………………………………………..20A 125VAC
Box Material……………………………………………………………………………………………..Galvanized Steel
Knockout size……………………………………………………………………………………………………………..1/2″
Adjustable Height………………………………………………………………………………………….up to 1″ depth

DESCRIPTION/ FEATURES

Included is a One gang floor box with a tamper-resistant 20 amp single receptacle, FB-06 box, gasket, and cover.

Compact and stylish design with adjustable height function metal box with the choice of Brass(C) or Stainless Steel (SS).
Corrosion-resistant hardware ensures a long life span and reliable performance.
Easy access to power when you need it.
Used for carpet and wood floors.

WARNING

Turn the POWER OFF at the circuit breaker before installing the Floor Box.
Read and understand these instructions before installing.
This device is intended for installation following the National Electric Code and local regulations.
It is recommended that a qualified electrician perform this installation.
Make sure to turn off the circuit breaker or fuse(s) and make sure the power is off before wiring the device. Use copper wire only.

NOTES: 10-12 AWG Stranded or Solid Copper wire is recommended.

DIMENSIONS

FLOOR BOX INSTALLATION

Before Installation:

Ensure there is sufficient depth & space below the sub-floor.

Step 1

For carpeted floors:
- Cut out a section of carpet smaller than the size of the cover.
For wood sub-floors:
- Tape the template on the area you want to place the floor box.
- Use a knife to cut the outline of the box. Start with the ears and move inwards.
- Following the outline, cut the box shape without the ears completely through the subfloor or hardwood floor.
- Following the outline, cut 3/8″ deep into the subfloor for the mounting ears.
- DO NOT ROUT OUT THE FINISHED FLOOR.
Step 2
- Remove knockouts and secure the box onto the floor. Pull the wires through the opening of the floor and the knockout and connect the wires based on the wiring diagram.
- Use the proper connector/ clamp at the knockouts to secure the wires and to avoid accidental wire stripping.
- Secure the box to the opening using wood screws.

WIRING DIRECTIONS

Connect the HOT wire to the BLACK wire.
Connect the NEUTRAL wire to the WHITE wire.
Connect the GROUND wire to the GREEN wire.

WARRANTY INFORMATION

This device is warranted to be free of material and workmanship defects for 2 years from the date of purchase.
An original receipt or proof of purchase from an authorized retailer must be presented upon warranty claim.
ALL claims must be verified and approved by Enerlites, Inc.
Warranties from other Enerlites products may vary.
This warranty is non-transferable and does not cover normal wear and tear or any malfunction, failure, or defect resulting from misuse, abuse, neglect, alteration, modification, or improper installation.
To the fullest extent permitted by the applicable state law, Enerlites shall not be liable to the purchaser or end-user customer of Enerlites products for direct, indirect, incidental, or consequential damages even if Enerlites has been advised of the possibility of such damages.
Enerlites’ total liability under this or any other warranty, express or implied, is limited to repair, replacement, or refund.
Repair, replacement, or refund are the sole and exclusive remedies for breach of warranty or any other legal theory.