LAKEMID DET Series Nightstands Set of 2 with Charging Station and Drawer User Manual

Table of Contents

LAKEMID-DET-Series-Nightstands-Set-of-2-with-Charging-Station-and-Drawer-
product-image

The LAKEMID End Tables with Charging Station are a versatile and functional addition to any living space. These end tables feature a built-in charging station, allowing you to conveniently charge your electronic devices while keeping them within reach.
These end tables are designed for use in the US and come in three color options: DETBR (Dark Brown), DETBK (Black), and DETGY (Gray).

General Guidelines

Please read the following instructions carefully and use the product accordingly.
Keep this manual and hand it over when transferring the product.
This summary may not include every detail of all variations and considered steps.
Contact us for further information and help.

Notes

It is recommended that 2 adults assemble the product using the included tool. Strictly follow the assembly steps.
If there is any odor after unpacking, put the product in a ventilated place for several days to air out.
Ensure all parts are intact before assembly. If there are any damaged or missing parts, stop assembly and contact us immediately. It is recommended to assemble the product on a soft surface.
Loosely tighten screws first, then fully tighten them after finishing the assembly.
Inspect the tightness of screws regularly and tighten again if necessary.
Protect the product from strong sunlight, damp environments, and mildew.
For daily care, clean it with a damp cloth first, then wipe dry.

Warnings

During assembly, keep all small parts out of the reach of children as it may be fatal if swallowed or inhaled.
To avoid the potential dangers of suffocation, keep all parts and packaging (film, plastic bags, foam, etc.) away from babies and children.
Do not stand or sit on the product.
Never touch the product with sharp or corrosive objects.
Do not place overweight items on top of this product.
Children are not allowed to climb on or play with the product for safety reasons as this may cause the product to tip over and result in immeasurable injury.
Make sure all parts and screws are tightened for a stable structure before use to reduce safety hazards.

Accessories List

Assembly Instructions

Step 1: Fully tighten all the screws. (X8)
Step 2 : Make sure the two ends are in the same side. Do not fully tighten the screws yet. (X4)
Step 3: Do not mix up 2 and 3. Use the shorter screws for 2 and longer screws for 3. Do not fully tighten the screws yet. (X4)
Step 4: (X1)
Step 5: Do not fully tighten the screws yet. (X4)
Step 6: Fully tighten all the screws above. Do not mix up 3 and 2. Use the longer screws for 3 and shorter screws for 2. (X4)
Step 7: (X4)
Step 8: Fully tighten all the screws. (X2)
Step 9: Fully tighten all the screws. (X1, X1)
Step 10: Connect the USB of the LED strip and the USB socket of the outlet.
Step 11: (X1, X2)
Step 12: Fully tighten the screw. (X1)
Step 13: Repeat the above steps to assemble the second one.
Step 14 : Congratulations!

Setting LED Light Control

Unplug the LED light and wait for a few seconds.
Plug in the LED light, within 5 seconds, press and hold the POWER and BRIGHT buttons at the same time until the LED flashes white light.
The LED light strip is currently restricted to be controlled only by this remote. However, if you press and hold the red button until the LED flashes white light, it will restore the ability to be controlled by any remote.

End Tables with charging station

Please read the following instruction carefully and use the product accordingly.
Please keep this manual and hand it over when you transfer the product.
This summary may not include every detail of all variations and considered steps. Please contact us when further information and help are needed.

Notes

lt is recommended that 2 adults assemble the product using the included tool, Strictly follow the assembly steps.
lf there is any odor after unpacking, put the product in a ventilated place for several days to air out.
Ensure all pats are intact before assembly. lf there are any damaged or missing parts, stop assemble and contact us immediately. lt is recommended to assemble the product on a soft surface.
Loosely tighten screws first, then fully tighten them after you finish the assembly.
Inspect the tightness of screws regularity and tighten again if necessary.
Protect the product from strong sunlight, damp environments, and mildew.
For daily care, please clean it with a damp cloth first, then wipe dry.

During assembly, keep all small parts out of the reach of children. lt may be fatal if swallowed or inhaled.
To avoid the potential dangers of suffocation, please keep all parts and packaging (film, plastic bags, foam.etc.) away from babies and children.
Do not stand or sit on the product.
Never touch the product with sharp or corrosive objects.
Please do not place overweight items on the top of this product.
Children are not allowed to climb on or play with the product for safety reasons. as this may cause the product to tip over and result in immeasurable injury.
Make sure all parts and screws are tightened for a stable structure before use to reduce safety hazards.

EXPLODED

$LAKEMID-DET-Series-Nightstands-Set-of-2-with-Charging-Station-and-Drawer-01 $9$$

$LAKEMID-DET-Series-Nightstands-Set-of-2-with-Charging-Station-and-Drawer-01 $14$$

CONGRATULATION!!

$LAKEMID-DET-Series-Nightstands-Set-of-2-with-Charging-Station-and-Drawer-01 $20$$

step1. Unplug the LED light and wait for a few seconds.
step2. Plug in the LED light, within 5 seconds, press and hold the “POWER” and “BRIGHT-” buttons at the same time until the LED flash white light. $LAKEMID-DET-Series-Nightstands-Set-of-2-with-Charging-Station-and-Drawer-01 $21$$

The LED light strip is currently restricted to be controlled only by this remote.
However, if you press and hold the red button until the LED flash white light. it will restore the ability to be controlled by any remote. $LAKEMID-DET-Series-Nightstands-Set-of-2-with-Charging-Station-and-Drawer-01 $22$$