Enerlites HMT01N 24hr Mechanical In Wall Timer Instruction Manual
- June 14, 2024
- ENERLITES
Table of Contents
Enerlites HMT01N 24hr Mechanical In Wall Timer
Product Information
Product Name
HMT01N – 24hr Mechanical In-Wall Timer
Wiring Directions
- Connect the BLACK wire on the switch to the HOT wire.
- Connect the WHITE wire on the switch to the NEUTRAL wire.
- Connect the Red wire on the switch to the LOAD wire.
Specifications
The HMT01N is a 24-hour mechanical timer that is easy to use. It has three colored wires that simplify the replacement of an existing switch/timer. The pins are built onto the Timer, reducing the chance of losing them. The dial is a mechanical clock, making it quick and easy to set the time.
Features
- Easy installation and replacement of existing switch/timer
- Pins built onto the Timer to prevent loss
- Mechanical clock dial for quick and easy time setting
Warnings
Before installing the Timer, turn off the power at the circuit breaker. It is recommended to have a qualified electrician perform the installation. Ensure that the circuit breaker or fuse(s) are turned off and power is off before wiring the device. Install the device in accordance with the National Electric Code and local regulations. Use Copper wires ONLY.
Product Usage Instructions
Setting/Operating
- Each pin on the Timer represents 30 minutes. Shaded numbers on the dial are for PM, and unshaded numbers are for AM.
- Example: To turn OFF the Load for 1 hour and 30 minutes starting from 8 PM and turn ON the Load at 9:30 PM, pull the 3 pins outwards that correspond with the Shaded 8 through 9.
Warranty Information
- For warranty information, please visit www.enerlites.com
SPECIFICATIONS
- Voltage ……………………………………….…………………….…………………..….. 120VAC, 60Hz
- Resistive……………….………….…………………………………………………………….15Amp, 1800W
- Electronic Ballast………..…..…………………..…………………………………………………………500VA
- Tungsten…………………………………………………………………………………….……………………1250W
- Motor…..…..…………………..………..…..…………………..……………………………………………1/2hp
- Operating Temperature ……………………………………………………………….32 to 104°F (0 to 40°C)
DESCRIPTION
- The HMT01N is a 24-hour mechanical timer that is very easy to use and the three colored wires make it very easy to replace an existing switch/ timer.
- The pins are built onto the Timer, which reduces the chance of losing pins.
- The dial itself is a mechanical clock, so setting the time is quick and easy.
FEATURES
- 24-hour ON/OFF timer.
- Up to 24 ON and 24 OFF settings
- Each pin counts for 30 minutes
- Replaces standard single pole switches
- Indoor use only
WARNING
- Turn the POWER OFF at the circuit breaker before installing the Timer
- Read and understand these instructions before installing. It is recommended that a qualified electrician perform this installation. Make sure to turn off the circuit breaker or fuse(s) and make sure the power is off before wiring the device.
- This device is intended for installation in accordance with the National Electric Code and local regulations.
- Use Copper wires ONLY.
WIRING DIRECTIONS
- Connect the BLACK wire on a switch to the HOT wire.
- Connect the WHITE wire on the switch to the NEUTRAL wire.
- Connect the Red wire on a switch to the LOAD wire.
SETTING/ OPERATING
- Set the Clock: Turn the dial until the “Current Time Pointer” points to the actual time.
- Set the ON/OFF times: Using the “Timer ON/OFF Pins, Pull outwards, the pins that correspond with the desired OFF time. Push inwards, the pins that correspond with the desired ON time.
- NOTE: Each pin represents 30 Minutes. Shaded numbers are for PM and unshaded numbers are for AM.
Example: Pulling the 3 pins outwards that correspond with the Shaded 8 through 9 will turn OFF the Load for 1 hour and 30 minutes starting from 8 PM and turning ON the Load at 9:30 PM.
ON/OFF/TIMER SWITCH:
- ON Position overrides the Timer schedule and turns the Load ON.
- OFF Position overrides the Timer schedule and turns the Load OFF.
- TIMER Position automates the Load ON/OFF according to the PIN settings.
WARRANTY INFORMATION
- This device is warranted to be free of material and workmanship defects for 2 years from the date of purchase. An original receipt or proof of purchase from an authorized retailer must be presented upon warranty claim. ALL claims must be verified and approved by Enerlites, Inc. Warranties from other Enerlites products may vary.
- This warranty is non-transferable and does not cover normal wear and tear or any malfunction, failure, or defect resulting from misuse, abuse, neglect, alteration, modification, or improper installation. To the fullest extent permitted by the applicable state law, Enerlites shall not be liable to the purchaser or end-user customer of Enerlites products for direct, indirect, incidental, or consequential damages even if Enerlites has been advised of the possibility of such damages. Enerlites’ total liability under this or any other warranty, express or implied, is limited to repair, replacement, or refund. Repair, replacement, or refund are the sole and exclusive remedies for breach of warranty or any other legal theory.
- © 2016 Enerlites Inc. CA, U.S.A.
- WWW.ENERLITES.COM 0208160037-02
- REV 20230802
Documents / Resources
|
Enerlites HMT01N 24hr Mechanical In Wall
Timer
[pdf] Instruction Manual
HMT01N 24hr Mechanical In Wall Timer, HMT01N, 24hr Mechanical In Wall Timer,
Mechanical In Wall Timer, Wall Timer, Timer
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>