Fosmon C-10683 Electrical Wireless Remote Control User Manual

Fosmon C-10683 Electrical Wireless Remote Control

Introduction

Thank you for purchasing this Fosmon product. For optimum performance and safety, please read this user manual carefully before operating and keep it for future reference. Fosmon’s Wireless Remote Control Outlet remotely turn ON/OFF decorative/holiday lighting, lamps and electronic devices wirelessly with a single button. You can conveniently control your security lights, patio lights, or holiday decoration without stepping outside.

Package Includes

• One outlet, one Remote, and one Battery (CR2032) for C-10683
• Two outlets, two remotes, and two batteries (CR2032) for C-10757US
• User Manual

Specification

• Max range in Open Area – 30m/89.4ft
• For outdoor and indoor use
• Max load: 15A Resistive or General purpose
• 125VAC, 60HZ,15A, Resistive
• 125VAC, 60HZ,15A, General purpose
• 125VAC, 60HZ, 10A / 1250W, Tungsten
• 125VAC, 60HZ,1/2HP TV-5
• Frequency: 433.92MHz
• Learned transmitter and receiver code
• ETL Listed

Product Diagram

Safety Precautions

• If using outdoors, be sure to plug into a GFCI approved outlet, and hang with outlet facing down.
• This will prevent water from penetrating the outlet.
• This is not waterproof. DO NOT submerge or place in an area susceptible to flooding or standing water.

RF warning statement:
To maintain compliance with FCC’s RF exposure guidelines, this equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.

Installation and Operation

Pairing Operation

• Open battery cover of the remote and put 1 pc CR2032 in it. The positive (+) side of the battery should be face-up. Then press ON/OFF button to see if the LED indicator turns on. If it turns on, the remote is functioning.
• Plug the receiver into a 3-prong AC outlet. The receiver’s LED indicator flashes slowly, indicating that the receiver is in the pairing mode.
• While the LED indicator on the receiver flashes slowly, press the remote’s ON/OFF button once to pair with the receiver.

Note : The receiver will exit pairing mode after either paired or 29 seconds.

• Press the remote’s button to turn your receiver

Un-pairing Operation

• Unplug the receiver and plug it back in again (The LED indicator on the receiver will flash slowly indicating that it is in pairing mode).
• Then press and hold the remote’s button for 3-4 seconds (You should see the receiver’s LED flash quickly for 3-4 seconds). After this, the receiver will return back to pairing mode.
• Unplug the receiver.
• The receiver should now be unpaired with the remote.

Follow Us On Social Media

• www.fosmon.com
• support@fosmon.com

Limited Lifetime Warranty
This fosmon product includes a limited lifetime warranty. Please visit our Fosmon website for more details.

Recycling the Product
To dispose of this product properly, please follow the recycling process regulated in your area.

FCC

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

• this device may not cause harmful interference, and
• this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for comollance could void the user’s authority to oberate the eauipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user Is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FAQs

, allowing users to operate devices from a considerable distance within the specified range.” image-3=”” headline-4=”p” question-4=”Is the Fosmon C-10683 easy to set up?” answer-4=”Yes, the Fosmon C-10683 is designed for easy setup. It usually comes with clear instructions to help users quickly pair the remote control with the corresponding receiver.” image-4=”” headline-5=”p” question-5=”Can the Fosmon C-10683 control multiple devices?” answer-5=”Some models of the Fosmon C-10683 are designed to control multiple devices, offering users the convenience of operating different electrical appliances with a single remote.” image-5=”” headline-6=”p” question-6=”Is the remote control powered by batteries?” answer-6=”Yes, the Fosmon C-10683 remote control is typically powered by batteries, and users should check the product specifications for the specific battery requirements.” image-6=”” headline-7=”p” question-7=”Does the Fosmon C-10683 come with a warranty?” answer-7=”The Fosmon C-10683 remote control may come with a limited warranty. Users are advised to check the product documentation or contact the manufacturer for warranty details.” image-7=”” headline-8=”p” question-8=”Is the remote control compatible with smart home systems?” answer-8=”Depending on the model, the Fosmon C-10683 may or may not be compatible with smart home systems. Users should check product specifications for compatibility details.” image-8=”” headline-9=”p” question-9=”Can the Fosmon C-10683 be used outdoors?” answer-9=”The Fosmon C-10683 is generally designed for indoor use. Outdoor use may depend on the specific model and its weather-resistant features. Users should check product specifications for details.” image-9=”” headline-10=”p” question-10=”Is the remote control programmable?” answer-10=”Some models of the Fosmon C-10683 may offer programmable features, allowing users to customize settings and functions according to their preferences.” image-10=”” headline-11=”p” question-11=”What frequency does the Fosmon C-10683 remote control operate on?” answer-11=”The Fosmon C-10683 remote control typically operates on a specific radio frequency (RF). Users should check the product specifications for details on the frequency.” image-11=”” headline-12=”p” question-12=”Can the Fosmon C-10683 remote control be used with non-Fosmon receivers?” answer-12=”In most cases, the Fosmon C-10683 is designed to work with compatible Fosmon receivers. Using it with non-Fosmon receivers may not guarantee proper functionality. Users should follow manufacturer recommendations.” image-12=”” count=”13″ html=”true” css_class=””]

Video-Introduction

Download This PDF Link: Fosmon C-10683 Electrical Wireless Remote Control User Manual

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>