Kraus KPF-1610 Bolden Single Handle 18-Inch Commercial Kitchen Faucet with Air Gap Instruction Manual
- June 14, 2024
- Kraus
Table of Contents
Kraus KPF-1610 Bolden Single Handle 18-Inch Commercial Kitchen Faucet with
Air Gap Instruction Manual
Tools Required
-
Tools Required
-
Phillips Screwdriver
-
Silicone Sealant
-
Safety Goggles
-
Pipe Tape
Care & Maintenance
- To keep the product clean & shining, follow the steps below:
- Rinse with clean water & dry with a soft cloth
- Do not clean with soaps, acid, polish, abrasives or harsh cleaners
- Do not use cloth with a coarse surface
- Unscrew the aerator and clean when necessary
- This installation manual is subject to change without further notice.
Diagram and Parts List
A. Spray Head
B. Faucet Body
C. Mounting Hardware
C1. Rubber & Metal Washer
C2. Mounting Nut
C3. Mounting Screws
D. Quick Connector
E. Weight
E1. Weight Clip
E2. Weight
F. 2.5mm Hex Wrench
Faucet Dimensions
Installer Tip:
Shut off main water supply before installing new faucet.
Step 1. Remove mounting hardware
Shut off the water supply. Remove the old faucet. Clean the mounting
surface. Remove mounting hardware (C) from faucet body (B)
Step 2. Installing the faucet assembly
Optional No Escutcheon Installation. Insert faucet body through the hole in
the sink or countertop.
Step 3. Securing the faucet assembly
Install the rubber washer and metal washer (C1) onto the threaded mounting
shank. Thread the nut (C2) onto the mounting shank. Lock the nut (C2) into
position by tightening the screws (C3). Do not overtighten.
Step 4. Securing the faucet assembly
Push the quick connector (D) firmly upward and attach it to the receiving
block (1). Pull down moderately to ensure the connection has been made.
Step 5. Installing the counterweight
Install the weight clip (E1) at the point of the hose marking “weight here”.
Insert the weight (E2) onto the clip (E1) by sliding it down onto the clip
(E1).
Step 6. Making the waterline connections
Thread the nut (1) on the supply line onto the outlet of the water supply
valve and tighten with a wrench. Do not overtighten.
NOTE: Please make sure filter washers are installed before connecting to
the main valve.
Step 7. Flushing and checking for leaks
Pull the hose assembly out of the spout and remove the spray head by
unscrewing it from the hose in a counterclockwise direction. Be sure to hold
the end of the hose down into the sink and turn the faucet on to the warm
position where it mixes hot and cold water. Flush the water lines for one
minute. This flushes away any debris that could cause damage to internal
parts. Check for leaks. Retighten any connections if necessary, but do not
overtighten. Reinstall the spray head by hand tightening it back onto the
spray hose. After installation is completed, turn on the hot and cold water
supplies. Check for leaks.
Replacement Parts
Replacement Parts Lis | Finish/Color | Part # |
---|---|---|
1.Sprayer | CH,SFS,SS,SB,MB,SFSB,BG,BB SFACB,SFACBMB,BGMB** | KP27216 |
2. Screen Washer | KP27208 | |
3. Sprayer Hose | BLBG,BLMB,BLSFS,BLSS,GRCH BLSFACB,GRSFS,GRSS,BLBB* | KP27247 |
4. Flow Regulator Assembly (1.8GPM) | WH** | KP27074 |
5. Quick Connector Assembly | KP27090 | |
6.. Spring Assembly | CH,MB,SB,SFS,BG,SS,SFSB** | KP27220 |
6. Spring Assembly | SFACB,BB** | KP27322 |
7. Sprayer Holder Assembly | CH,SFS,SS,SB,SFSMB,BG,SFACB,BB | |
MB,SFACBMB,BGMB,SFSB,MBSB, SFSCH,SSCH,SSMB,MBSFSB,BBMB** | KP27218 | |
7.1. Inverter | KP27245 | |
7.2. Wearable Ring & O-ring Assembly | KP27085 | |
8. Set Screw | BL,GR** | KP27084 |
9. Index | KP27124 | |
10. Cartridge Kerox K-35 | KP27083 | |
11. Bonnet Nut | KP27082 | |
12. Cap | CH, SFS, SS, SB, MB, BG, SFACB, SFSB, BB** | KP27081 |
13.. Handle Assembly | CH, SFS, SS, SB, MB, BG, SFACB, SFSB, BB** | KP27072 |
14. Set Screw | KP27001 | |
15. Cover Button | BL,GR** | KP27002 |
16.Washer | KP27091 | |
17. Rubber & Metal Washe | KP27028 | |
18. Mounting Nut & Screws | KP27079 | |
19. Block | KP27073 | |
20. O-ring | KP27092 | |
21. Weight & Clip Assembly | KP27236 | |
22. Hex Wrench | KP27020 | |
23. Inverter | KP27123 | |
24. Filter Washers | KP27167 |
Denotes spray hose assembly color options : Spray hose assembly color options: Black hose w/Brushed Gold connector (BLBG), Black hose with Spot-Free Stainless connector (BLSFS), Gray hose with Chrome connector (GRCH), Gray hose with Spot-Free Stainless connector (GRSFS), Gray hose with Stainless Steel connector (GRSS), Black hose with Matte Black connector (BLMB), Black hose with Stainless Steel connector (BLSS), Black hose with Spot-Free Antique Champagne Bronze (BLSFACB), Black hose with Brushed Brass (BLBB) **Denotes faucet component color options:
- CH – Chrome
- SFS – Spot Free Stainless Steel
- SS – Stainless Steel
- MB – Matte Black
- BG – Brushed Gold
- SB – Black Stainless
- BB – Brushed Brass
- MBSFSB – Matte Black/Spot Free Black Stainless
- SFACB – Spot Free Antique Champagne Bronze
- MBSB – Matte Black/Black Stainless
- SFSCH – Spot Free Stainless Steel/Chrome
- BGMB – Brushed Gold/Matte Black
- SFSB – Spot Free Black Stainless
- SFSMB – Spot Free Stainless Steel/Matte Black
- SSMB – Stainless Steel/Matte Black
- SSCH – Stainless Steel/Chrome
- BBMB – Brushed Brass/Matte Black
- SFACBMB – Spot Free Antique Champagne Bronze/Matte Black
- BL – Black WH – White GR- Grey
Troubleshooting
If you have followed the instructions carefully and your faucet still does not work properly, take the following corrective steps:
PROBLEM | CAUSE | ACTION |
---|---|---|
Leakage under faucet handle | Bonnet nut (11) has come loose | Remove the cover |
button (15). Loosen set screw (14) with hex wrench (22). Remove the handle.
Unscrew cap (12). Tighten bonnet nut (11) with an adjustable wrench
The aerator has an irregular or reduced water flow| The aerator is dirty or
mis-fitted| Remove the aerator and check for debris. Ensure that the rubber
washer is properly installed
The water pressure is low.| The connector underneath the deck is clogged with
debris
The aerator is clogged
| Turn off the water supply and disconnect the connector / aerator. Unscrew the connector / aerator and clean under running water. Screw the connector / aerator back.
Test water flow. If water pressure is still low then replace the connector / aerator
There is a low flow of water.| The screen filters in the hose connectors are dirty| Turn off the water supply at the water valves and unscrew the hose connectors from the water supply lines. Clean the screens in the water lines with hot water, removing any debris or calcium build up.
Codes/Standards Applicable:
-
NSF/ANSI 372
-
NSF/ANSI/CAN 61: Q ≤ 1
-
LEAD FREE
NSF/ANSI 61 -
ASME A112.18.1
1.8GPM 6.8L/min maximum
Faucet – Lifetime Limited Warranty
Kraus USA Plumbing, LLC (“Kraus”) extends this warranty to the original purchaser for personal household use of the
Faucet when purchased from an authorized Kraus dealer and in the location of original installation. This warranty is non-transferable.
Kraus warrants the structure and finish of the Faucet to be free from defects in material and workmanship under normal usage for as long as the original purchaser resides in the residence in which the Faucet was first installed.
Kraus warrants the Faucet’s sprayhead assembly (including the engine, aerators, structure, restrictors, back flow preventers, sprayer hoses, braided supply line hoses which encompasses nylon, silicon and stainless steel) of the product to be free from defects in material and workmanship under normal usage for a period of one (1) year from the date of purchase.
Kraus warrants the Faucet’s cartridge to be free from defects in material and workmanship under normal usage for a period of five (5) years from the date of purchase.
Any product reported to the authorized dealer or to Kraus as being defective within the warranty period will be repaired or replaced with a product of equal value at the option of Kraus.
Commercial Warranty
Kraus USA Plumbing, LLC (“Kraus”) warrants its Products for a period of one
(1) year to commercial purchasersof Products used in industrial, commercial
and business applications.
Care and Cleaning Instructions
Certain cleaning products may cause damage to a Product’s finish and use of
the following on the Product will void this warranty
- Abrasive cleaners such as powders, bleach, ammonia, alcohol or chorine
- Abrasive pads, steel wool or wire brushes
What is Not Covered
This warranty does not cover Products that were discontinued when purchased or display Products, whether such Products were purchased at discount outlets, unauthorized dealers, and/or sold on clearance. This warranty does not cover any free gifts included with purchase.
This warranty does not cover damage resulting from neglect, misuse (including use for an unintended application), abuse, carelessness, accident, hard water or mineral deposits, exposure to corrosive materials, improper maintenance, alteration of the Product, or failure to follow care, cleaning or installation instructions enclosed with your Product. Kraus recommends that all Kraus Products be installed by a fully licensed and insured trade professional with experience in the installation of bathroom and/or kitchen manufactured goods
How to Make a Warranty Claim
If you are a consumer purchaser , please contact a Kraus Customer Service
Representative at:
Kraus USA Plumbing, LLC
12 Harbor Park Drive
Port Washington, NY 11050
Toll-free 800-775-0703
Customerservice@kraususa.com
If you are a plumbing contractor or trade professional , please contact a
Kraus Pro Representative at:
Kraus USA Plumbing, LLC
12 Harbor Park Drive
Port Washington, NY 11050
516-801-8955
Proservice@kraususa.com
If you are an authorized partner , please contact a Partner Support
Representative at:
Kraus USA Plumbing, LLC
12 Harbor Park Drive
Port Washington, NY 11050
516-801-8954
Partnersupport@kraususa.com
In requesting warranty service, please be ready to provide your proof of purchase and a description of the problem. Shipping charges will be covered for the first (1) year of the warranted replacement part or product (HI, AK, and Puerto Rico shipping charges may apply). International shipping fees are not included.
Limitation on Duration of Implied Warranties
Please note that some states/provinces (including Quebec) do not allow
limitations on how long an implied warranty lasts, so the below limitations
may not apply to you. TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, ANY
IMPLIED WARRANTY, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND OF
FITNESS FOR A PARTICULAR PURPOSE, IS LIMITED TO THE STATUTORY PERIOD OR THE
DURATION OF THIS WARRANTY, WHICHEVER IS SHORTER.
Limitation of Special, Incidental or Consequential Damages
Please note that some states/provinces (including Quebec) do not allow the
exclusion or limitation of special, incidental or
consequential damages, so the below limitations and exclusions may not apply
to you. TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS WARRANTY DOES
NOT COVER, AND KRAUS USA PLUMBING, LLC SHALL NOT BE LIABLE FOR, ANY SPECIAL,
INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING LABOR CHARGES TO REPAIR,
REPLACE, INSTALL OR REMOVE THIS PRODUCT), WHETHER ARISING OUT OF BREACH OF ANY
EXPRESS OR IMPLIED WARRANTY, BREACH OF CONTRACT, TORT, OR OTHERWISE.
This warranty gives you specific legal rights, and you may also have other rights which vary from state/province to state/province.
Download the Kraus Care & Maintenance Guide at:
http://www.kraususa.com/maintenance
IMPORTANT
Register Your Kraus Product
Activate Your Warranty
Access Premium Customer Support
Get Product Information
REGISTER TODAY
http://www.kraususa.com/registration
www.kraususa.com
References
- Kraus | Kitchen and Bathroom | Sinks, Faucets, and Accessories
- Care & Maintenance | Well-crafted products | Light maintenance.
- Kraus USA Self Help
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>