Healthkeep FG2001B-A Smart Full Body Composition Scale Instruction Manual

Healthkeep FG2001B-A Smart Full Body Composition Scale

INSTALLATION INSTRUCTION

1. Download the “Fitdays” App from the Apple Store or Google Play.
2. Remove the plastic isolation sheet from the battery cover.
3. Place the scale on a hard flat surface.
4. Measure with bare feet and full contact with the electrodes.
5. Turn on the smart App and get the scale connected before measuring.
6. Follow the below operations and make sure the posture is correct for measuring.
   • Arms not straight
   • Arms close to waist
   • Keep your arms straight 45 degrees or 90 degrees
   • The tail finger does not touch the electrode pad
   • Two thumbs close together
   • Keep your all fingers touch the electrode pads

Healthkeep Smart Full Body Composition Scale

• Thanks for choosing the Smart Full Body Composition Scale. This scale uses bio-electrical impedance analysis (BIA) technology to help you conveniently measure.
• Body weight, Body balance, BMI, Body fat rate, Visceral fat, Body water, Skeletal muscle rate, Muscle mass, Bone mass, Protein, BMR, Body age, etc.

WARNING

• DO NOT use with medical implants such as pacemakers.
• DO NOT stand on the edge of the scale or jump on it;
• DO NOT overload the scale (Max.180kg/440lb/28st)
• DO NOT drop the scale or drop the objects on it as this may damage the sensors.
• DO NOT immerse the scale in water or use chemical cleaning agents. Clean the scale with a slightly damp cloth.
• Not recommended for pregnant women.
• Not recommended for infants, toddlers, and children who are under 10 years of age.
• Any measurement obtained using this device is for reference only and should not be considered as a medical opinion.
• DO NOT be used to diagnose or treat any medical condition. You should consult your primary care doctor or physician before making changes to your diet, exercise plan, or physical activities.
• Always place the scale on a hard, dry, and flat surface before measurement.
• Make sure your feet are dry before stepping on the scale.
• Connect the batteries in accordance with the correct polarities indicated.
• Remove batteries if the scale is not used for a prolonged period of time
• DO NOT use the device if damaged. The continuous use of a damaged unit may cause injury or improper results. Please check the device before each use.
• First, check the battery’s power and replace it if needed, if the scale malfunctions.
• Be careful when using it on wet and slippery surfaces.

Product Specification

Indication Symbols

• The batteries in the scales are too weak. Insert new batteries (see the”Replacing the Batteries” chapter).
• More than 180kg are on the scales. The scales are overloaded.
• An error has occurred during measurement. Step off the scales for 5 seconds and step onto them again to repeat the measuring process.

Product Overview

Indication Symbols

iOS: 8.0 or higher
Android: 5.0 or higher

Install Fitdays App

1. Scan the below QR Code to download the APP, or search “Fitdays” from the Apple Store and Google Play.
2. Download and install the App “Fitdays” on your device.
3. The App icon will appear on your phone or tablet after the installation is completed.

How to use the scale with Fitdays App for the first time?

1. Open the App “Fitdays” on your device.
2. Register your own account by email or log in with a social media account.
3. Add personal data and confirm.
4. iOS: Make sure Bluetooth is on and Bluetooth Authorization is allowed.
   • Android: Make sure Bluetooth is on and GPS and Location are allowed.
5. In the back of the scale, pull out the insulation sheet, then place the scale on a hard, flat surface, and step onto the scale with a single foot to activate the scale. Wait until the display shows “0.0kg”.
6. Pair the scale through Bluetooth. Make sure the scale is on when pairing. Leaving the APP on its main screen, it will automatically connect to the scale. Or you could also click “Account“ —-> “Device”—> “+” —-> “Bluetooth” find the scale Bluetooth ID: HPS8007.
7. The app will show your data within a few seconds.

Bluetooth Connection

1. Regular Connection
   • See the “How to use the scale with Fitdays App for the first time?” chapter.
2. If the regular connection to Bluetooth fails, please try the below steps:
3. Reset the scale by taking out one battery for 5 seconds and putting it back in.
4. Reset the Bluetooth connection. Ensure Bluetooth and GPS (Android only) are enabled on your device.

  * Under the “Account” section, select the “Device”. Slide it left to delete the current device.
  * Tap “+” on the top right to enter pairing mode.
  * Step onto the scale with a single foot to wake it up.
  * After a few seconds of loading, the scale name will appear, tap and confirm it.
  * Step on the scale again to complete the pairing.

Troubleshooting

1. Bluetooth failed to connect
   • Make sure the scale and the Bluetooth and GPS (Android only) on your phone are on;
   • Check the system version of your smartphone, it must be iOS 8.0 or higher/Android 6.0 or higher;
   • For successful connection, there is a Bluetooth icon on the display, and the word “Connected” will show on the circle of the homepage on the phone;
   • If fail to connect via Bluetooth, please click Account—>Device to find the scale ID: HPS8007.
2. No body fat data after weighting
   • Must step onto the scale with bare feet.
   • Make sure your feet and the scale are both dry.
   • Step off the scale when the measurement does not finish (Please keep standing on the scale for around 10 seconds until the number on the display stops flashing).
   • Bluetooth is not turned on.
   • Bluetooth is paired with a different scale.
3. Incorrect weight data occurs.
   • Check whether the scale is on a hard, flat surface.
   • Check each sensor foot on the back to make sure nothing is stuck to the bottom of it.
4. The incorrect fat-muscle ratio shows on the App.
   • The body parameter settings are incorrect, check to make sure you entered the correct gender, height, and age.
   • Check if you activate the Athlete Mode.
5. How do I re-calibrate the scale after removing it?
   • Step on the scale to turn it on. Let it automatically drop to 0.0kg to calibrate.
6. The scale does not turn on
   • Check if the insulation sheet has been pulled out.
   • Check if the battery has run out of power and change new batteries if needed.

Frequently Asked Questions & Answers

1. 1. How to get the most accurate result?
   • Stand on the scale firmly, do not shake when weigh-in.
   • Take your measurement at the same time each day to ensure the most accurate results.
   • Please place your scale on the hard/flat ground, then step on the scale with bare feet, after that, the display will be turned on.
   • Check your profile information (gender, age, and height), and make sure all the data is accurate.
   • Check the place, and make sure it is hard/flat, someplace seems flat but is actually not, you could try to move to a different hard surface until it gets the same result.
   • Check the bottom of the scale before measurement, if it is not balanced, the data won’t be accurate.
   • Make sure that “0.0” is shown on the display, before each time use.
   • Keep bare feet, with each foot touching both the top and bottom electrodes.
2. How to restart the scale?
   • First, take one of the batteries out of the scale.
   • Then, put back the batteries and wait for 5 seconds.
   • After the scale has been automatically restarted, you can step onto the scale.
3. How to change language?
   • Fitdays APP—>Account—>Settings—>Language
4. How to change the unit?
   • Fitdays APP—>Account—>Settings—>Switch units

**For more information, please check FQA from Fitdays APP. “Account >Settings

FAQ” Advice**

• Place the scale far away from the children in case of falling down or crashing.
• Do not expose the scale to heat or fire, which will easily cause an explosion.
• Waste electrical products should not be disposed of with household waste.
• Please recycle where facilities exist.
• Check with your local Authority or retailer for recycling advice.
• healthkeephome@gmail.com
• Feel free to contact us and get more than you think!
• Read this manual before using and save for future reference

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>