Oster Master Series Blender User Manual

MASTER SERIES
BLENDER LICUADORA

Master Series Blender

Visit us at OsterBlending.com

IMPORTANT SAFEGUARDS

When using your blender, you should always follow basic safety precautions, including the following:

• Read all instructions before use.
• To protect against electrical hazards, do not immerse the cord, plug or motor base in water or other liquids.
• Always use the product on a clean, flat, hard, dry surface. There should be no material such as a tablecloth or plastic between the unit and surface.
• Flashing light indicates blender is ready to operate. Avoid ANY contact with the blades or moving parts.
• Keep hands and utensils out of jar while blending to reduce the risk of injury or damage to the blender. A scraper may be used but must be used only when the blender is not running.
• Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions, or is dropped or damaged in any manner. Return appliance to the nearest authorized service facility for examination, repair or electrical  or mechanical adjustment.
• The blender blades are sharp. Handle carefully.
• To reduce the risk of injury, never place cutter-assembly blades on base without jar properly attached.
• Always put the lid on the jar before operating the blender.
• When blending hot liquids beware of steam. Remove the filler cap from the lid to allow steam to escape.
• Do not use outdoors.
• Do not allow the cord to touch hot surfaces, including the stove, or hang over the edge of a table or counter.
• Unplug the blender when it is not in use, before taking off or putting on parts, and before cleaning. To disconnect, turn appliance off by pressing ON/Off button and remove plug from outlet.
• This appliance is not to be used by children or by persons with reduced physical, sensory or mental capabilities.
• Close supervision is necessary when any appliance is used near children. Children should not play with the appliance.
• Do not blend boiling liquids in the blender.
• The use of attachments, including canning jars, not recommended by the manufacturer may cause a risk of injury to persons.
• When blending hot liquids, remove center piece of two-piece cover.
• Do not attempt to replace or splice a damaged cord.

Food Processor Accessory Additional Precautions

• Be certain cover is securely locked in place before operating the appliance.
• Do not attempt to defeat the cover interlock mechanism.
• Never insert food by hand. Always use food pusher.
• Keep hands and utensils away from moving blades or discs while processing food to reduce the risk of severe injury to persons or damage to the food processor. A scraper may be used but must be used only when the food processor is not running.
• To reduce the risk of injury, never place cutting blade or discs on base without first putting bowl properly in place.

SAVE THESE INSTRUCTIONS
This product is for household use only.

• The maximum rating marked on the product is based on the attachment that draws the greatest load. Other attachments may draw less power.
  Power Cord Instructions:

• This appliance is equipped with a polarized plug for 120V and 127V units only.
  This type of plug has one blade that is wider than the other. This plug will fit in a polarized outlet only one way. This is a safety feature intended to help reduce the risk of electrical shock. If you are unable to insert the plug into the  outlet, contact a qualified electrician to replace the obsolete outlet. Do not attempt to defeat the safety purpose of the polarized plug by modifying the plug in any way.

• Try to position the blender near the power source to reduce the hazards associated with power cords (such as becoming entangled or tripping over a long power cord).

• Do not pull, twist or otherwise abuse the power cord.

• Do not wrap the power cord around the main body of the blender during or after use.

• Do not use an extension cord with this product.

This symbol has been placed in specific areas of the User Guide portion of this book. Its purpose is to help you easily identify instructions that require your special attention.

Welcome

Congratulations on your new Oster® Master Series Blender. Your Oster ® blender will allow you to create delicious smoothies, milkshakes, salsas and much more at the touch of a button! If you have any comments, questions or inquiries about this product, please call 1-800-334-0759. Your product includes the following features and benefits:

• User-friendly control panel.
• Advanced 6-Point Blade System which provides a wide range of food processing & blending options.
• Extra Wide Blade design allows food to fall easily to the bottom of the jar, for more efficient Blending!

For Best results, carefully read the instruction manual before using this appliance.
Learning About The Master Series Blender With Push Button Control Panel

1. Filler Cap / 2 Ounce Measuring Cup: – Allows you to add ingredients during use. Also allows you to open to allow steam to escape when blending hot foods.

2. Jar lid – Seals the blender jar.

3. Jar – 6-cup Dishwasher Safe Bookless glass jar withstands Thermal shock.
   Glass Jar Blade Assembly – With locking feature to secure blade assembly to threaded jar bottom.
   Seals the jar to the blade for leak-proof operation.

4. Sealing Ring :

5. Blade – 50% Larger blade system than traditional Oster Blenders.

6. Threaded Jar Bottom With Locking Lever –
   Advanced design for simple assembly to jar.

7. Motor Base – Holds the jar securely. Contains a powerful, variable speed motor.

8. Control Panel
   a. Power Button (Off button) – Turns the product Off.
   b. Variable Control settings range from Stir to Extract and also indicate the food results: from Easy Clean to Smoothie.
   c. Pulse button – Press to pulse and release to stop. Perfect for Crushing Ice.

Learning About The Master Series Blender With Electronic Control Panel (Select Models only)

1. Filler Cap / 2 Ounce Measuring Cup: – Allows you to add ingredients during use. Also allows you to open to allow steam to escape when blending hot foods.

2. Jar lid – Seals the blender jar.

3. Jar – 6-cup Dishwasher Safe Bookless glass jar withstands Thermal shock.
   Glass Jar Blade Assembly – With locking feature to secure blade assembly to threaded jar bottom. Seals the jar to the blade for leak-proof operation.

4. Sealing Ring :

5. Blade – 50% Larger blade system than traditional Oster Blenders.

6. Threaded Jar Bottom With Locking Lever – Advanced design for simple assembly to jar.

7. Motor Base – Holds the jar securely. Contains a powerful, variable speed motor.

8. Control Panel
   a. Power Button (On/Off button) – Turns the product On and Off.
   b. Pre-Programmed Settings: Use for flawless results at the touch of a button. Select the desired setting and your Oster ® Master Series blender cycle through the program, delivering expert results at the touch of a button. Unit will  Stop after running through the cycle. Select From: Green/ Frozen Smoothies Food Chop / Salsa
   c. Manual Controls: Select from Low-Med-High
   d. Pulse button – Press to pulse and release to stop.

Using The Oster ® Master Series Blender

Before you use the product for the first time, separate the lid, filler cap and blade from the jar. Wash in warm, soapy water, or top rack in the dishwasher. Rinse and dry well.
WARNING: Blade is sharp. Handle with care.

6 Cup glass Jar Assembly

1. Place Blade into Threaded Jar Bottom (Fig.1).

2. Place sealing ring over blade assembly. Carefully press and tuck sealing ring into locking groove (Fig2).

3. Ensure the locking sealing ring is fully and evenly tucked in place and holding the blade assembly to the threaded jar bottom. For correct assembly see (Fig3).

4. Install the Integrated Blade Assembly onto the Jar. Turn clockwise to tighten.
   Be sure the Integrated Blade Assembly is tightened to the jar before using.
   NOTE: For proper installation onto Blender Motor base, make sure locking lever rotates past the anti-rotation tabs on the Blender jar or smoothie cup. See (Fig4).
   CAUTION: If Locking Lever is damaged or missing, do not operate blender, and contact Customer Service for a replacement.

5. Put the ingredients into the jar.

6. Secure the lid and filler cap.

7. Place the jar onto the base.

8. Plug the power cord into a standard household
   120/127-volt, 60 hz. AC outlet. You are now ready to start.
   ALWAYS PLACE HAND ON CONTAINER COVER WHILE OPERATING BLENDER.

Using the Push Button Control Panel

1. Make Sure the “OFF” button is pressed before plugging in the blender.
2. Select setting and blend ingredients to desired consistency. Note: Control panel lists function as well as desired outcome.
3. Press OFF to stop and turn off blender.
4. Press and hold ICE CRUSH / PULSE for ice crushing and chopping. Repeat as needed.

Using the Pre-Programmed Settings (Select Models Only)

1. Press the ON/OFF power button to turn the product on. The power light will blink, indicating the product is active and ready to use. The light will stay on when the motor is running.

2. Select and Press the desired Pre-Programmed Setting Button:
   – “Green/Frozen Smoothie”
   – “Food Chop/Salsa”

3. To change your selection, press ON/OFF twice followed by another Preprogrammed Setting button (“Frozen Drinks & Shakes” or “Food Chop”)

4. Once the program is complete the product automatically stops. Please note: You may press the ON/OFF button to cancel the program at any time. The blinking bule light indicates that the blender is ready.

5. Press the ON/OFF power button to turn the product off. This product is pre-programmed to turn off automatically if not used for a period of several minutes. All lights will turn off when the unit automatically powers down.

Using the Manual Controls
The Manual Controls include:
Low
Med
High
Pulse
Use these controls for personal recipes or to continue blending after a Programmed Setting is finished.

1. Press the ON/OFF power button to turn the product on. The power light will blink, meaning the product is active and ready to use. The light will stay on when the motor is running.
2. Put the ingredients into the jar.
3. Secure the lid and the filler cap.

High

1. Press the “High” button to run the product at a high speed.
2. Press the ON/OFF power button to turn the product off.

Medium

1. Press the “Medium” button to run the product at a medium speed.
2.  Press the ON/OFF power button to turn the product off.

Low

1. Press the “Low” button to run the product at a low speed.
2.  Press the ON/OFF power button to turn the product off.

Pulse

1. Verify that the blue light is blinking. This indicates that the blender is turned on.
2. Press and hold the “Pulse” button.
3.  Release the pulse button to stop.
4. Press the ON/OFF power button to turn the product off.
   Use pulse button to crush ice or chop food.

Caring for Your Product

After Use

1. Press the OFF button and unplug blender. Lift the jar straight up from the base, remove the lid and empty the jar.
2. If necessary, use a rubber spatula to scrape foods away from the sides of the jar.

Cleaning
WARNING: Blades are sharp. Handle carefully.
CAREFULLY release the blade from the bottom of the jar by turning the threaded jar bottom counterclockwise. The jar lid, filler cap and blade are dishwasher safe. Use the top rack of the dishwasher for the jar lid, filler cap, and blade.  Place sealing ring into bottom basket of dishwasher.
You can also wash the parts in warm, soapy water. Rinse well and dry. Wipe the base with a soft, damp cloth to clean. Never submerge the blender base in a liquid.
Check the parts as you put them back together.
TIP: Run blender with soapy water for 20-30 seconds at Low or Medium Speed for cleaning without disassembly. Follow with clean water rinse.

Storing
Reassemble the blender for storage. Leave the lid open a gap so no odors are retained.
NOTICE: Never put the jar, or any other parts, in a microwave oven. Never store foods or drinks in the jar.
Servicing
This appliance has no user serviceable parts. Any servicing beyond the cleaning described in the Cleaning section should be performed by an authorized service representative only.
If repairs are needed, send your appliance only to an authorized OSTER® Appliance Service Center. Replacement parts are available on www.oster.com or  call 1-800-334-0759.

Blending Tips

Liquids
Put liquids into the jar first, unless the recipe says otherwise. Add more liquid if ingredients are not blending properly.
Using the Filler Cap
Do not remove the lid while in use. Instead, open the filler cap to add smaller ingredients.
Ice Crushing
Without Liquid: use pulse button until you achieve desired results.
With Liquid: Add desired amount of ice cubes and water until ice floats. Blend on High until you achieve desired results then strain off water.
Working with Hot Foods or Liquids
WARNING: When you work with HOT FOODS, remove the filler cap to vent steam. Tilt the lid away from you partially covering the opening. Keep hands and other exposed skin away from the lid opening to prevent possible burns.
WARNING: When you work with HOT LIQUIDS, remove the filler cap and start at a low speed, and then gradually increase to a faster speed. Do not add liquid over the 4 cup (1L) level. Always keep hands away from steam.

Ingredient Quantities
Use only the amount of food suggested in the recipes. If you want greater amounts, prepare in batches. Using larger amounts may overload and strain the motor. You might also get different results from those described.

Frequently Asked Questions

Why doesn’t the blender turn on?

• Make sure the base is plugged in an active power receptacle. • Verify blinking blue light is active after pushing on/off button.

How can I prevent liquids from leaking out?

Check to see that the sealing ring is correctly assembled in between the blade and the jar.

Blend-N-Go® Smoothie Cup Accessory (Select Models Only)
NOTE: For proper installation onto Blender Motor base, make sure locking lever rotates past the anti-rotation tabs on the smoothie cup.

A. Locking Lever
B. Anti-Rotation Tabs
C. Blender base
NOTE: Blend-N-Go® Smoothie cup attachment is only compatible with threaded jar bottom with locking lever, See Images below

To Purchase Smoothie Kit visit OsterBlending.com
Using Your Blend-N-Go® Cup With Your Oster Master Series Blender
Before washing ensure the blender is off and unplugged. Wash all components except blender base with soapy water with a soft sponge and a bottle brush. Do not use abrasive cleansers or sponges for cleaning. Rinse well and dry. Parts are also dishwasher safe. Do not blend hot liquids.
Place desired ingredients into smoothie cup in the following order: Liquids, fresh ingredients, frozen fruit, ice, yogurt and ice cream. (Cut all firm fruits, vegetables and other foods into pieces no larger than 1/2-inch (1.25 cm) by 2 inches (5.0 cm).

• Place Blade into Threaded Jar Bottom or adapter.
• Place sealing ring over blade assembly. Carefully press and tuck sealing ring into locking groove. (See page 7 for more detailed instructions for blade assembly)
• Place blade assembly into cup. (See Figure 1 on Page 17)
• Be sure the Integrated Blade Assembly is tightened to the jar before using.
• Place cup assembly onto Blender base. (See Figure 2 on Page 17)
• Hold cup in position. Operate Blender according to the instructions in your Blender User Manual. Blend until desired consistency.
• Place lid on cup and turn clockwise to tighten.
  Enjoy your blended drink!

ALWAYS PLACE HAND ON CONTAINER WHILE OPERATING BLENDER.

Recipes

Honey-Vanilla Blast

Makes 1 serving
1 cup fat free milk ¼ cup protein powder
2 Tbsp. honey
1 cup (8 oz.) fat free vanilla yogurt
3 chunks frozen banana, about 1 medium

1. In jar, place ingredients in order given above.
2. Cover jar with lid. Press “On / Off” button, then press “Smoothies” button until desired results are achieved.
3. Pour into tall glass to serve.

Very Berry Smoothie
Makes 1 serving

1 cup orange juice ½ cup vanilla low fat yogurt
1 cup frozen mixed berries
2 frozen banana chunks, about 1 small
2 Tbsp. Agave
1. In jar, place ingredients in order given above.
2. Cover jar with lid. Press “On / Off” button, then press “Smoothies” button until desired results are achieved.
3. Pour into tall glass to serve.
Fiery Red Salsa Recipe
Makes 3 cups
2 large garlic cloves
1 can (15 oz.) whole tomatoes, drained
1 medium onion, cut into ¼ (4 pieces)
½ cup cilantro leaves
1-4 jalapeno peppers, quartered
½-1 tsp. sugar
Salt to taste
1 Tbsp. lime juice
1 can (15 oz each) whole tomatoes, drained
Tortilla chips for serving

1. In jar, place ingredients, except tortilla chips, in order given above. (Note: Place one can of tomatoes in after garlic cloves and second can after rest of ingredients are added. Also, place onion in middle of jar to avoid blockage.)
2. Cover jar with lid. Press “On / Off” button, then press “PULSE” button.
3. Pour into bowl; serve with tortilla chips.

Peachy Applesauce
Makes 1 ¼ cups
1 large apple, pared, cored and quartered
1 large peach, pitted, peeled and quartered (If out of season, use 2 canned peach halves.)
2 Tbsp. water

1. In small saucepan, cook fruits in water 5-8 minutes or until very tender.
2. In jar, place fruits and liquid.
3. Cover jar with lid. Press “On/Off” button, then press “Pulse” button 3 or 4 times until smooth.
4. Remove from jar; place in covered containers.
5. Chill or freeze at once.

Peachy Green Smoothie
Makes: 2 servings
1 banana
½ avocado
1 cup ice
½ cup coconut water
½ teaspoon vanilla extract
1 peach, stone removed
1 cup Greek yogurt
1 cup baby spinach
1 tablespoon honey or agave

1. Place all ingredients into the tall blender jug. Secure the lid.
2. Blend on HIGH speed until all of the ingredients are blended, or use the Frozen Smoothies button function.
3. Pour into a tall glass. Serve.

Banana Chai Thick Shake
Makes: 3 servings
4 frozen bananas
1 cup ice
½ teaspoon ground turmeric
¼ teaspoon ground ginger Pinch sea salt
3 cups skim milk or coconut water
½ teaspoon ground cinnamon
¼ teaspoon ground cardamom
½ teaspoon ground star anise

1. Place all ingredients into the tall blender jug. Secure the lid.
2. Blend on HIGH speed until all of the ingredients are blended, or use the Frozen Smoothies button function.
3. Pour into a tall glass. Serve.

3 Year Satisfaction Guarantee
Sunbeam Products, Inc. doing business as Jarden Consumer Solutions or if in Canada, Sunbeam Corporation (Canada) Limited doing business as Jarden Consumer Solutions (collectively “JCS”) warrants that for a period of three (3)  years from the date of purchase, this product will be free from defects in material and workmanship. JCS, at the Consumer’s sole option, will repair, or replace this product or any component of the product found to be defective during the guarantee period. This guarantee is valid for the original retail purchaser from the date of initial retail purchase and is not transferable. Keep the original sales receipt. Proof of purchase is required to obtain satisfaction guarantee  performance. JCS dealers, service centers, or retail stores selling JCS products do not have the right to alter, modify or any way change the terms and conditions of this guarantee.
All Metal Drive Ten (10) Year Limited Warranty
JCS also warrants that for a period of ten (10) years from the date of purchase, the All Metal Drive base unit metal coupling will be free from defects in material and workmanship. JCS, at its option, will repair or replace the metal drive  stud component of the All Metal Drive coupling if found to be defective during the warranty period. Replacement will be made with a new or remanufactured product or component. If the product is no longer available, replacement may  be made with a similar product of equal or greater value. This is your exclusive warranty. Do NOT attempt to repair or adjust any electrical or mechanical functions on this product.
This warranty does not cover damage resulting from any  of the following: negligent use or misuse of the product, use on improper voltage or current, use contrary to the operating instructions, disassembly, repair or alteration by anyone other than JCS or an authorized JCS service center.  Further, the warranty does not cover: Acts of God, such as fire, flood, hurricanes and tornadoes.
This warranty is valid for the original retail purchaser from the date of initial retail purchase and is not transferable. Keep the original sales receipt. Proof of purchase is required to obtain warranty performance. JCS dealers, service  centers, or retail stores selling JCS products do not have the right to alter, modify or any way change the terms and conditions of this limited warranty.
What are the limits on JCS’ Liability?
JCS shall not be liable for any incidental or consequential damages caused by the breach of any express, implied or statutory warranty or condition. Except to the extent prohibited by applicable law, any implied warranty or condition of  merchantability or fitness for a particular purpose is limited in duration to the duration of the above limited warranty. JCS disclaims all other warranties, conditions or representations, express, implied, statutory or otherwise. JCS shall  not be liable for any damages of any kind resulting from the purchase, use or misuse of, or inability to use the product including incidental, special, consequential or similar damages or loss of profits, or for any breach of contract,  fundamental or otherwise, or for any claim brought against purchaser by any other party. Some provinces, states or jurisdictions do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long  an implied warranty lasts, so the above limitations or exclusion may not apply to you. This limited warranty gives you specific legal rights, and you may also have other rights that vary from province to province, state to state or jurisdiction to jurisdiction.
How to Obtain Satisfaction Guarantee and/or Limited Warranty Service
In the U.S.A.
If you have any question regarding this guarantee or limited warranty or would like to obtain guarantee or limited warranty service, please call 1-800-334-0759 and a convenient service center address will be provided to you.
In Canada
If you have any question regarding this guarantee or limited warranty or would like to obtain guarantee or limited warranty service, please call 1-800-667-8623 and a convenient service center address will be provided to you.
In the U.S.A., this guarantee and limited warranty is offered by Sunbeam Products, Inc. doing business as Jarden Consumer Solutions located in Boca Raton, Florida 33431. In Canada, this guarantee and limited warranty is offered by  Sunbeam Corporation (Canada) Limited, located at 20 B Hereford Street, Brampton, Ontario L6Y 0M1. If you have any other problem or claim in connection with this product, please write to the Consumer Service Department.
PLEASE DO NOT RETURN THIS PRODUCT TO ANY OF THESE ADDRESSES OR TO THE PLACE OF PURCHASE.
For inquiries regarding recycling and proper disposal of this product, please contact your local waste management facility.

For product questions contact:
Sunbeam Consumer Service
USA : 1.800.334.0759
Canada : 1.800.667.8623
www.oster.com
©2016 Sunbeam Products, Inc., doing business as
Jarden Consumer Solutions. All rights reserved.
In the U.S., distributed by Sunbeam, Products, Inc.,
doing business as Jarden Consumer Solutions, Boca Raton, FL 33431
In Canada, imported and distributed by Sunbeam Corporation (Canada) Limited,
doing business as Jarden Consumer Solutions, Brampton (Ontario) L6Y 0M1.
Tritan™ is a trademark of Eastman Chemical company used with permission.
Printed in USA
Master Series Blender_16ESM1
Impreso en EEUU
GCDS-OST47250-BB

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>