ieGeek ZS-GX2S Wire Free Outdoor Battery Security Camera User Manual

ieGeek ZS-GX2S Wire Free Outdoor Battery Security Camera User Manual

Technical Support

If you need help, please contact ieGeek before returning your product Most questions can be answered through our online support center at www.iegeek.com or our after-sale mailbox at: service@iegeek.com.

Please read this manual thoroughly before using this wireless security camera. If you have any issues, please email your order number and the problem TO our mailbox: service@iegeek.com. Receiving your message, we will provide a fast solution in 24 hours.
Warming Tip:

• Before connecting this camera to the Wi-Fi, please ensure the Wi-Fi signal strength is to be over than 75% to keep good Wi-Fi signal.
• This wireless camera supports events recording when Wi-Fi disconnected.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help. Responsible for compliance could void the user’s authority to operate this equipment. (Example- use only shielded interface cables when connecting to computer or peripheral devices).

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and,
2. This device must accept any interference received, including interference that may cause undesired operation.

FCC Radiation
Exposure Statement: The equipment complies with FCC Radiation exposure limits set forth for uncontrolled environment This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. (FCC ID: 2AZL7-ZS-GX2S)

Camera introduction

1. Antenna

2. Lens

3. Working statu light

4. Microphone

5. PR
   

6. Reset Button

7. Charging Indicator

8. Speaker

9. Power Button

10. SD Card Slot

11. Dedicated Charging Port

APP Download and Account Registration

Download ‘ieGeek Cam’ APP
Method 1: Download ‘ieGeek Cam’ or ‘CloudEdge’ APP from APP Store (iOS and Android);
Method 2: Scan ‘ieGeek Cam’ APP QR code to download it.

Tips:
Please turn on 2 below permissions while using this APP for the first time.

• Allow ‘ieGeek Cam’ APP to access mobile cellular data and wireless LAN or it will fail to add IP camera.
• Allow ‘ieGeek Cam’ APP to receive pushed message or the phone will not receive alarm push when motion detection or audible alarm is triggered.

Register Account
New users need to register by email. The concrete steps are as following:

1. Click “Register”;
2. Follow the steps to complete the registration of the account;
3. Log in.

Note:

• When registering a new account, please choose the region which you are actually in and correct country code. (Different registered regions can’t share the camera.)
• Please choose to register by e-mail. Please choose to register by e-mail.

How to Add a Camera to APP

Before Using:

1. Please insert the Micro SD card before power on, otherwise, the SD card cannot be detected.
2. Put the camera and smart phone 1-3 ft (30-100 cm) away from the router to set Wi-Fi.
3. Make sure that the camera is using 2.4GHz Wi- Fi.

Wi-Fi Connection Steps

Tap ‘+’ to Add Device

Select Battery Camera

Power on Camera

Reset Device

Input Wi-Fi Password

Scan QR Code

Wait for Connection

Device Added

(Note: If it can’t be powered on, please plug in DC 5V 2A power adapter to charge the camera for 15min first)

My camera fails to connect Wi-Fi?

1. Please make sure the Wi-Fi the camera connected is 2.4GHZ.
2. Make sure the password correction of the Wi-Fi. (Note: the password of the WiFi cannot include single quote, underline, space and virgule (/).
3. Once the devices that your router connected excess the its max limit numbers, other devices will cannot connect the router.
4. Make sure the QR code on the phone screen is normal and the distance between the phone and the camera lens is 10-15cm (3.9-5.9inch) during the scanning process.
5. If the camera cannot connect the Wi-Fi, please try to re-download the APP, reset the camera and restart the router, and then add the camera again.
6. If you tried all steps, but still no luck, please message your order and problem to service@iegeek.com.

Charge the Battery

Charge the battery with a 5V 2A power adapter

• The battery is a built-in battery and cannot be removed. Charge the battery with the ieGeek Solar Panel. For the weatherproof performance, always cover the dedicated charging port with the rubber plug after finishing charging the battery.

Charging Indicator:
Red LED: Charging Blue
LED: Fully Charged

Installation Guides

Mounting Height: 2-3 Meters

PIR Detecting Distance: 2-10Meters

• Use the camera waterproof plug for better weatherproof performance when you install the camera outdoors.

• Install the camera 2-3 meters (7-10 ft) above ground. The detection range of the motion sensor would be maximized at such a height. •
  Install the camera 2-3 meters(7-10 ft) above ground. The detection range of the motion sensor would be maximized at such a height.

• For effective motion detection, please install the camera angularly.

NOTE: If a moving object approaches the PIR sensor vertically, the camera may fail to detect motion.

Notes on PIR Motion Sensor

PIR Sensor Detection Range
The PIR detection range can be customized to meet your specifific needs. You may refer to the following table to set it up in Device Settings via ieGeek Cam App.

Important Notes on Reducing False Alarms

• Do not face the camera towards any objects with bright lights, including sunshine, bright lamp lights, etc.
• Do not place the camera near any outlets, including the air conditioner vents, humidififier outlets, the heat transfer vents of projectors, etc.
• Do not install the camera at places with strong wind.
• Do not face the camera towards a mirror.
• Keep the camera at least 1 meter away from any wireless devices, including WiFi routers and phones in order to avoid wireless interference.

FAQS

For more detailed FAQS, please log in to the APP, search in “Me”-“EAQ”-“Help Document”-“Battery Camera

The device prompts offline?

Update router or Wi-Fi password?

Delete the camera from your CloudEdge account. After resetting the device, use the new Wi-Fi and password to add it again.

Will not connect to WiFi?

1. The wifi currently connected to the the mobile phone is a 2.4Ghz network; The current location has good wifi coverage and a stable network (wifi signal is greater than 75%); 2) Avoid using wifi extender, 3) Check whether the wifi password is entered correctly; It cannot be ruled out that in the rare case of special network incompatibility, the App and the camera cannot be connected correctly. In. this case, our camera is not compatible, please contact the after-sales service first.(service@ iegeek.com)

Fast power consumption?

1. In the case of poor wifi coverage (such as signal is below 75%), which will increase power consumption; 2) The PIR trigger frequency is high,and the power consumption will increase when infrared light/ white light is on at night; 3) The mobile phone often accesses the camera remotely, which will increase the power consumption; 4) For the first use,it's recommended to use the power to 10%, and then charge it to 100%, which is helpful for the health of the lithium battery

Camera not detecting movement?

1. In the case of unstable network,the message may not be pushed in time after the PIR is trigged.In this case, you can first confirm the network status and remove the camera to verify and confirm in an environment with good network coverage; 2) Inappropriate installation position will result in PIR not triggering and not detecting. If the position is too high, the object is too far away, or the object is too small, the camera will not trigger, try to adjust the installation position according to the trigger requirements for many times.

SD card not recognized?

1. Support capacity is 16-128GB micro SD card; 2) Before use, make sure to format the micro SD card as FAT32 or exFAT file system on the computer, then insert it into the camera, and finally perform the format memory card operation on the camera again; 3) If the micro SD card is not recognized during use, it is generally a quality problem of the micro SD card, and it is necessary to replace the memory card with more stable reading and writing.

Points de collecte sur www.quefairedemesdechets.fr

FR
Vaus êtes responsible de remettre tous les appareils électriques et électoniques usages à des points de collected correspondents. Pour en savoir plus : www.quefairedemesdechets.fr

Prolinx GmbH Brehmstr. 56, 40239 Duesseldorf Germany

Prolinx Global LTD27 Old Gloucester Street London, WC1N 3AX, UK

B210-220022 FCC ID: 2AZL7-ZS-GX2S WEIYE 株式会社 Made in China Model: ZS-GX2S

Sales Email: service@iegeek.com
Official website: https://www.iegeek.com

Validate your warranty within 7 days and get 2-year extended warranty on your iegeek security products.


Email: service@iegeek.com

Scan the QR code : to get the latest version of the PDF manual

www.iegeek.com
leGeek and leGeek logo are trademarks of Shenzhen Globalebuy Co., Ltd, registered in the United States and other countries. All right reserved.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>