Oladance OWS2 Open Ear Headphones User Guide
- June 14, 2024
- Oladance
Table of Contents
Oladance OWS2 Open Ear Headphones
In the box
Note: Ear supporters as an optional accessory, which can be used to enhance the wearing stability of the earbuds if needed.
Product Introduction
Get Started
- Open case lid, Bluetooth is ready to pair when breathing light starts to blink.
- Control Music
- Tap Once: Play / Pause
- Make Phone Call
- Tap Once: Answer a call
- Control Music
- Tap Twice: Left bud: Previous track
- Right bud: Next track
- Make Phone Call
- Tap Twice: End or decline a call
- Activate Voice Assistant
- Control Music
- Slide Forward: Volume up
- Slide Back: Volume down
- Make Phone Call
- Slide Forward: Volume up
- Slide Back: Volume down
Clear Bluetooth pairing list
- Tap and hold 5s on both buds at the same time
About Oladance APP
- Download Oladance APP to enjoy more customization and cool feature.
- Let’s have fun with your Oladance Wearable Stereo!
Using Instructions
Connection
Multi-point connection
- Enable multi-point connection: After the first device is connected, press and hold both headset touch pads at the same time for 2 seconds, after hearing a beep the headset enters pairing mode again, the second device can search for the headset and connect.
- Disconnect multi-point connection: When the headset has been connected to 2 devices, press and hold the two headset touch pads for 2 seconds at the same time, after hearing a beep, the headset disconnects all Bluetooth devices and enters pairing mode.
Operation temperature: 0~45°C
Input: 5.0V 1A
Disposal and Recycling Information
This symbol (with or without a solid bar) on the device, batteries (included), and / or the packaging, indicates that the device and its electrical accessories (for example, a headset, adapter or cable) and batteries should not be disposed of as household garbage.
Battery warning
The built-in lithium battery of the product is forbidden to be disassembled, impacted, extruded or put into fire. The battery under the very low air pressure may result in explosion or flammable liquid or gas leakage. Avoid the battery in a high-temperature environment or being exposed to strong sunlight to avert explosion. Don’t use the battery continuously in case of serious ballooning. The battery shall be handled pursuant to the local regulations and shall not be disposed as household garbage. Don’t try to repair, remove or refit the battery. The explosion may happen if the battery is replaced by the one subject to incorrect model. Don’t compress or puncture the battery with hard object. The battery leakage, overheating or outbreak of a fire may occur if the battery is destroyed.
Declaration of Conformity
Hereby, Shenzhen Dancing Future Technology Ltd., declares that this device is in compliance with Directive 2014/53/EU.
SAR: RF exposure information: The EIRP power of the device at maximal case is below the exempt condition, 20mW specified in EN 62479: 2010. RF exposure assessment has been performed to prove that this unit will not generate the harmful EM emission above the reference level as specified in EC Council Recommendation (1999/519/EC)
FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference
- this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit dilerent from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help important announcement.
RF Exposure
The portable device is designed to meet the requirements for exposure to radio waves established by the FCC RF exposure guidelines. These requirements set a SAR Limit of 1.6 W/kg averaged over one gram of tissue. The highest SAR value is measured at a distance of 0mm between the radiator and the Head. The highest reported Head SAR value: 0.66W/kg.
RF Exposure
The portable device is designed to meet the requirements for exposure to radio waves established by the ISED. These requirements set a SAR limit of 1.6 W/kg averaged over one gram of tissue. The highest SAR value is measured at a distance of 0mm between the radiator and the Head. The highest reported Head SAR value: 0.66W/kg.
- FCC ID: 2A9AR-OLA06L
- FCC ID: 2A9AR-OLA06R
- IC: 29727-OLA06L
- IC: 29727-OLA06R
- HVIN: OLA06L
- HVIN: OLA06R
- 201-220755
- CMIIT ID: 2022DP19264
Important Note: Radiation Exposure Statement
- This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 0cm between the radiator and your body.
- This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Warning
- Don’t place the product into a liquid environment or avoid the product exposed to high humidity
- Avoid extrusion to avert the damage to the product
- Don’t attempt to dismantle the product. Put the product in a cool and dry place to keep it dry if stored for a long time
- Avoid touching the strong magnet to prevent the magnetic headset from being demagnetized.
- Avoid the dusty, wet and dirty environment where the electronic circuit of the equipment may be damaged if being used.
- Don’t Use the equipment at the moment of thunderstorm because the thunderstorm may incur equipment fault or shock hazard.
- Don’t use the equipment when riding a motorcycle or a bicycle,driving a car or crossing the road to ensure your safety.
- Keep the equipment out of reach of children or pets to avert the damage.
- Don’t wash the equipment with chemical cleanser or strong detergent
Don’t Listen to the voice under high sound pressure and high volume for a long time to prevent the possible hearing impairment when the headset is used.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
- this device may not cause interference.
- this device must accept any interference, including interference that may cause undesired operation of the device.