iotty LSW2E2 Smart Wi-Fi Switch for Light and Gate Instruction Manual
- June 14, 2024
- iotty
Table of Contents
Model: E2PLUS
ID: LSW2E2
MLS2E202
Technical specifications
E2 PLUS Smart Switch
Model: E2PLUS
ID: LSW2E2
Input: 230 Vac
Frequency: 50Hz
Max 5A per RL
Ambient temperature: 25°C
Operating temperature: from 0°C to 40°C
Only works with 2.4GHz Wi-Fi band
Frequency range: 2412-2472MHz
Maximum RF output power of the product: 17.29 dBm
RF exposure information: The Maximum
Permissible Exposure (MPE) level is calculated based on a distance of d=20 cm
between the device and the human body. To maintain compliance with the RF
exposure requirement, a separation distance of 20 cm between the device and
the human should be maintained.
Important notes
Safety Precaution
Incorrect installation is dangerous or illegal. Install in accordance with all
national and local codes.
Hire a professional electrician if you are not familiar or not comfortable
with electrical work, or if the wiring in your electrical box looks different
from the pictures.
For indoor use and dry location only.
Installation Precaution
Neutral wire required. Input L/N should be connected to a 16 A circuit
breaker, and each way output should be connected to a 5 A circuit breaker
before used.
Cable size: from 1,2 mm2 to 2,5 mm2 – select the cable size properly according
to the load current.
Multi-way (3-way via Wi-Fi)
A 3-way switch allows you to control an electrical load (lamp) from 2
different locations.
Thanks to the Multi-way feature, you can connect multiple iotty switches
together through the Wi-Fi network and take control of the same light.
For more details check: link.iotty.com/multi-way
Troubleshooting
In case of network error, try these steps in order:
- Restart the router and wait a few minutes to allow all devices to reconnect OR, if the problem persists,
- With the palm of your hand, cover all the buttons and hold for a long time to restart the device OR, if the problem persists,
- Remove the faceplate and push the AP button on the switch. Repeat device registration
Warranty
For warranty information visit us at
link.iotty.com/warranty
Device overview
Installation steps
Turn off the power at
the circuit breaker for the switch you are replacing. 
Remove your old switch and label your wires.
Remember that you must have neutral wire. 
Wire the iotty plate
Insert the power wire into terminal L. Insert the neutral wire into terminal
N. Connect the wires on RL: insert the load wire in one terminal of RL and the
power wire in the other terminal of RL. Repeat the operation on the other RLs
if you need to use more keys. If you have a ground wire, put insulating tape
or a hooded terminal to insulate it and place it into the wall box. Compare
the wiring with the electrical scheme in the picture to be sure everything is
in place.
Electrical scheme for a load that operates at a different voltage from iotty
device: 
Electrical scheme for a load that
needs a pulse to activate:To set the switch
properly, go to the iotty app, go to Device Settings and under “Switch Type”
select “Pulse Switch”.
Screw the iotty
switch in
Push all the wires back into the wall box (do not push the wires using the back of the switch). Insert the device in the wall box and screw it in. Position the switch so that the AP and reset buttons are located on the left.
Attach the glass faceplate
Attach the faceplate so that the little circle is located at the bottom.
http://link.iotty.com/play-store
http://link.iotty.com/app-store
Turn on the power and register device
Turn on the power at the circuit breaker. Check if the wiring was made
correctly by tapping on the glass to turn on and off the light. Now the
installation is complete and you can proceed to register the device.
iotty devices are compatible with the following integrations 
If you need more information you can contact us at
support@iotty.com or visit our FAQ section
https://support.iotty.com/hc
IOTTY srl
Via Del Laghetto, 18/20
33080 Porcia (PN) – ITALY
iotty@iotty.com
support@iotty.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>