iotty E1PLUS WiFi Connected Smart Switch User Manual
- June 17, 2024
- iotty
Table of Contents
iotty E1PLUS WiFi Connected Smart Switch
Technical specifications
E1 PLUS Smart Switch
Model: E1PLUS
ID: LSW2E1
Input: 230 Vac
Frequency: 50Hz
Max 5A per RL
Ambient temperature: 25°C
Operating temperature: from 0°C to 40°C
Only works with 2.4GHz Wi-Fi band Frequency range: 2412-2472MHz
Maximum RF output power of the product: 17.29 dBm
RF exposure information: The Maximum Permissible Exposure (MPE) level is
calculated based on a distance of d=20 cm between the device and the human
body. To maintain compliance with the RF exposure requirement, a separation
distance of 20 cm between the device and the human should be maintained.
Important notes
Safety Precaution
Incorrect installation is dangerous or illegal. Install in accordance with all
national and local codes.
Hire a professional electrician if you are not familiar or not comfortable
with electrical work, or if the wiring in your electrical box looks different
from the pictures.
For indoor use and dry location only.
Installation Precaution
Neutral wire required. Input L/N should be connected to a 16 A circuit
breaker, and each way output should be connected to a 5 A circuit breaker
before used.
Cable size: from 0.2mm2 to 2.5mm2 – select the cable size properly according
to the load current.
Multi-way (3-way via Wi-Fi)
A 3-way switch allows you to control an electrical load (lamp) from 2
different locations.
Thanks to the Multi-way feature, you can connect multiple dotty switches
together through the Wi-Fi network and take control of the same light.
For more details check: link.iotty.com/multi-way
Troubleshooting
In case of network error, try these steps in order:
-
Restart the router and wait a few minutes to allow all devices to reconnect
OR, if the problem persists, -
With the palm of your hand, cover all the buttons and hold for a long time to restart the device
OR, if the problem persists, -
Remove the faceplate and push the AP button on the switch. Repeat device registration
Warranty
For warranty information visit us at link.iotty.com/ warranty
Device overview
It restarts the device, all settings remain saved.
It makes the dotty Wi-Fi visible again.
Useful to re-register the device on the app, update the Wi-Fi credentials, or
turn off the device Wi-Fi.
5 mm (0.20 in) Distance between the back of dotty device and the wall
Installation steps
-
Turn off the power at the circuit breaker for the switch you are replacing.
-
Remove your old switch and label your wires. Remember that you must have neutral wire.
-
Wire the dotty plate
Insert the power wire into terminal L. Insert the neutral wire into terminal N. Connect the wires on RL: insert the load wire in one terminal of RL and the power wire in the other terminal of RL. Repeat the operation on the other RLs if you need to use more switches. If you have a ground wire, put insulating tape or a hooded terminal to insulate it and place it into the wall box.
Main power supply 230 Vac
= Live/power
= Neutral
= Load/lamp
= Load/lamp
Electrical scheme for a load that operates at a different voltage from dotty device:
Electrical scheme for a load that needs a pulse to activate:
To set the switch properly, go to the dotty app, go to Device Settings and under “Switch Type” select “Pulse Switch”.
= Power
= Neutral
Main power supply 230 Vac
= Power
= Neutral
Main power supply 230 Vac
-
Screw the dotty switch in
Push all the wires back into the wall box (do not push the wires using the back of the switch). Insert the device in the wall box and screw it in. Position the switch so that the AP and reset buttons are located on the left.
-
Attach the glass faceplate
Attach the faceplate so that the little circle is located at the bottom.
-
Turn on the power and register device
Turn on the power at the circuit breaker. Check if the wiring was made correctly by tapping on the glass to turn on and off the light. Now the installation is complete and you can proceed to register the device iotty devices are compatible with the following
App
integrations
If you need more information you can contact us at
support@iotty.com or visit our
FAQ section
Customer Support
IOTTY sol
Via Del Larghetto, 18/20
33080 Porcha (PN) – ITALY
iotty@iotty.com
support@iotty.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>