iotty E2PLUS WiFi Connected Smart Switch Instruction Manual

June 9, 2024
iotty

E2PLUS WiFi Connected Smart Switch
Instruction Manual

Model: E2PLUS
ID: LSW2E2
MLS2E201

Technical specifications

E2 PLUS Smart Switch
Model: E2PLUS
ID: LSW2E2
Input: 230 Vac
Frequency: 50Hz Max 5A per RL
Ambient temperature: 25°C
Operating temperature : from 0°C to 40°C Only works with 2.4GHz Wi-Fi band
Frequency range: 2412-2472MHz
Maximum RF output power of the product : 17.29 dBm
RF exposure information: The Maximum
Permissible Exposure (MPE) level is calculated based on a distance of d=20 cm between the device and the human body. To maintain compliance with the RF exposure requirement, a separation distance of 20 cm between the device and the human should be maintained.

Important notes

Safety Precaution

Incorrect installation is dangerous or illegal. Install in accordance with all national and local codes.
Hire a professional electrician if you are not familiar or not comfortable with electrical work, or if the wiring in your electrical box looks different from the pictures.
For indoor use and dry location only.

Installation Precaution
Neutral wire required. Input L/N should be connected to a 16 A circuit breaker, and each way output should be connected to a 5 A circuit breaker before used. Cable size:  from 0.2mm 2 to 2.5mm 2 – select the cable size properly according to the load current.
Multi-way (3-way via Wi-Fi)
A 3-way switch allows you to control an electrical load (lamp) from 2 different locations.
Thanks to the Multi-way feature, you can connect multiple dotty switches together through the Wi-Fi network and take control of the same light.
For more details check: link.iotty.com/multi-way

Troubleshooting

In case of network error, try these steps in order:

  • Restart the router and wait a few minutes to allow all devices to reconnect OR, if the problem persists,
  • With the palm of your hand, cover all the buttons and hold for a long time to restart the device OR, if the problem persists,
  • Remove the faceplate and push the AP button on the switch. Repeat device registration

Warranty
For warranty information visit us at link.iotty.com/warranty

Device overview

iotty E2PLUS WiFi Connected Smart Switch

It makes the dotty Wi-Fi visible again. Useful to re-register the device on the app, update the Wi-Fi credentials, or turn off the device Wi-Fi. . iotty
E2PLUS WiFi Connected Smart Switch - fig

Installation steps

iotty E2PLUS WiFi Connected Smart Switch - stepsTurn off the power at the circuit breaker for the switch you are replacing.

iotty E2PLUS WiFi Connected Smart Switch - steps1

Remove your old switch and label your wires.
Remember that you must have neutral wire.

iotty E2PLUS WiFi Connected Smart Switch - steps2

Wire the iotty plate
Insert the power wire into terminal L. Insert the neutral wire into terminal N. Connect the wires on RL: insert the load wire in one terminal of RL and the power wire in the  other terminal of RL. Repeat the operation on the other RLs if you need to use more keys. If you have a ground wire, put insulating tape or a hooded terminal to insulate it  and place it into the wall box. Compare the wiring with the electrical scheme in the picture to be sure everything is in place.
Electrical scheme for a load that operates at a different voltage from dotty device:

iotty E2PLUS WiFi Connected Smart Switch - iotty
device

Electrical scheme for a load that needs a pulse to activate:
iotty E2PLUS WiFi Connected Smart Switch - iotty device
1To set the switch properly, go to the dotty app, go to Device Settings and under “Switch Type” select “Pulse Switch”. iotty E2PLUS WiFi Connected Smart Switch -
steps3

Screw the iotty switch in
Push all the wires back into the wall box (do not push the wires using the back of the switch). Insert the device in the wall box and screw it in. Position the switch so that the  AP and reset buttons are located on the left.

iotty E2PLUS WiFi Connected Smart Switch - steps4

Attach the glass faceplate
Attach the faceplate so that the little circle is located at the bottom. iotty E2PLUS WiFi Connected Smart Switch - steps5

|
---|---
http://link.iotty.com/play-store| http://link.iotty.com/app-store

Turn on the power and register device
Turn on the power at the circuit breaker. Check if the wiring was made correctly by tapping on the glass to turn on and off the light. Now the installation is complete and you  can proceed to register the device.
iotty devices are compatible with the following

integrations

iotty E2PLUS WiFi Connected Smart Switch - app

If you need more information you can contact us at support@iotty.com or visit our FAQ section

https://support.iotty.com/hc

iotty devices are compatible with the following integrations

iotty E2PLUS WiFi Connected Smart Switch - app1

If you need more information you can contact us at support@iotty.com or visit our
FAQ section

https://support.iotty.com/hc

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals