MoesGo RF433 No Neutral Wire WiFi Smart Touch Wall Light Switch Instruction Manual

June 14, 2024
MoesGo

MoesGo logo

Instruction Manual
Smart Switch
Wi-Fi+RF433 Single Live

MoesGo RF433 No Neutral Wire WiFi Smart Touch Wall Light
Switch

MoesGo RF433 No Neutral Wire WiFi Smart Touch Wall Light Switch - Icon
1

MoesGo RF433 No Neutral Wire WiFi Smart Touch Wall Light Switch - Qr Code
1

https://drive.google.com/drive/folders/1JltZ-r
NsngwgsM7pCMZQnnyy-r9VQoUH?usp=sharing

Product Description

This new designed glass panel wireless touch smart switch is designed with WiFi+RF to replace traditional switches with a variety of ways to control.Now one new smart feature as multi-control association to other smart switches is added into the Smart  Life/Tuya App,together with the backlight on/off and relay status.And its scratch resistance glass panel is suitable for different decoration styles with its best value.
Note: Button sound on and off: no button operations before operations begin within 6 seconds.Then press switch button for 4 times and long press for the fourth time until the switch beep sounds as Di-Di for 2 times for successful operation.

Safety Information

Risk of Electric Shock:Electricity can cause personal injury and property damage if handled improperly.If you are not sure about any part of these instructions,please seek professional assistance from a qualified electrician.

Technical Parameters:

Model: WS-EU-RF / WS-US-RF
Voltage: US: 90-130V AC, 60Hz/200-240V AC, 50Hz
EU: 200-240V AC, 50Hz
Max. current: 2.5A/Gang; Total 2.5A
Wireless protocol: Wi-Fi 2.4GHz+RF433MHz

Warnings:
Turn off the power at the circuit breaker and test that power is off before wiring.

Installation

Note:
Make sure that the power at the circuit breaker is off before wiring.
Neutral wire in not required(single live line).
The wire colors indicated in this manual are the usual colors and may differ in some houses.
Ensure the wire conductors are securely fastened to each wire.
Ensure the Wi-Fi signal is steady and normally working before wiring.
If you don’t have any wiring experience, please call a professional electrician.

Step 1

  • Turn off the circuit breaker and use the electrical tester to test the power.
  • Ensure the circuit breaker is off before wiring.

Attention:
Please disconnect the power supply before installing or removing the device for avoiding irreversible damage on the device from the electric current or some unpredictable problems such as lamp flashing.

Step 2

  • Remove the old switch

MoesGo RF433 No Neutral Wire WiFi Smart Touch Wall Light Switch - Remove the
old switch

Step 3

  • Remove the switch and pull it away from the wall.
    Identify Line/Load Wire(Note:The color of your wire may be different from the color shown on the manual.)

Verify power is off

  • We recommend you remove the faceplate from the old switch and use an electrical tester to test all wires connected to the switch to ensure there is no voltage in the circuit.
  • You may need to turn off more than one circuit breaker.

Step 4

  • Take pictures of the wiring
    MoesGo RF433 No Neutral Wire WiFi Smart Touch Wall Light Switch - Take
pictures of the wiring

  • Follow the wiring diagram to connect the switch wires to the wires in the wall box with the wire conductors.

Step 5
Remove the panel with screwdriver
(Please don’t install with electricity power on)

Step 6

  • Prepare to install wiring
    A. Live wire connects “ L ” terminal
    B. Lamp wire connects “ L1,L2,L3,L4 ” terminal
    1 Gang connects “L1” terminal
    2 Gang connects “L1,L2” terminal
    3 Gang connects “L1,L2,L3” terminal
    4 Gang connects “L1,L2,L3,L4” terminal

  • Capacitor Installation
    When the lamp lights or starts flashing, Please connect Capacitor the as shown in the drawing:
    1 Gang L1 and N line.
    2 Gang L1 and N line.
    3 Gang L1 and N line.
    4 Gang L1 and N line.

1-3 Gang

MoesGo RF433 No Neutral Wire WiFi Smart Touch Wall Light Switch -
Gang

4 Gang

MoesGo RF433 No Neutral Wire WiFi Smart Touch Wall Light Switch - Gang
2

MoesGo RF433 No Neutral Wire WiFi Smart Touch Wall Light Switch - Gang
3

Step 7
Open the switch panel from the bottom of the switch with a screwdriver

MoesGo RF433 No Neutral Wire WiFi Smart Touch Wall Light Switch - switch
panel

  • Mount the switch with the provided screws and snap the wall plate on it.

Step 8
Turn the power back on at the circuit breaker and then switch the light on.

Download the MOES APP

  1. Download MOES App on App store or scan the QR code
    MoesGo RF433 No Neutral Wire WiFi Smart Touch Wall Light Switch - Qr Code
3https://a.smart321.com/moeswz
    MOES App is upgraded as much more compatibility than Tuya Smart/Smart Life App, functional well for scene controlled by Siri, widget and scene recommendations as the fully new customized service.
    (Note: Tuya Smart/Smart Life App still works, but MOES App is highly recommended)

  2. Registration or Log in.
    • Download “MOES” Application.
    • Enter the Register/Login interface; tap “Register” to create an account by entering your phone number to get verification code and “Set password”. Choose “Log in” if you already have a MOES account.

Steps for connecting the APP to the device

Method One:

  1. Make sure your phone is connected to Wi-Fi and Bluetooth.

  2. Scan the QR code to configure the network guide.
    MoesGo RF433 No Neutral Wire WiFi Smart Touch Wall Light Switch - Method One
2MoesGo RF433 No
Neutral Wire WiFi Smart Touch Wall Light Switch - Qr Code
4https://smartapp.tuya.com/s/p?p=icygzrleh60pt3ij&v=1.0

Method Two:

  1. Make sure your phone is connected to Wi-Fi and Bluetooth.

  2. Reset: Press the switch button for 6 times, and hold on the 6th time, then release until you hear Di-Di-Di(3 times), and the blue indicator on the switch will flash fast after 3 seconds.
    Reset/repair is successful.

  3. Open MOES/Tuya App, then the prompt page will automatically show on the screen.Click “Add”, Select the device you want to add and click “+”.
    MoesGo RF433 No Neutral Wire WiFi Smart Touch Wall Light Switch -
prompt

  4. Enter Wi-Fi Password and click “Next”, waiting for completing the connection. Add the device successfully, you can edit the name of the device to enter the device page by click “Done” .
    MoesGo RF433 No Neutral Wire WiFi Smart Touch Wall Light Switch -
Password

  5. enjoy your smart life with home automation.
    MoesGo RF433 No Neutral Wire WiFi Smart Touch Wall Light Switch -
home

How to reset/repair Wi-Fi code

Press the switch button for 6 times,and hold on the 6th time, then release until you hear Di-Di-Di(3 times), and the blue indicator on the switch will flash fast after 3 seconds.Reset/repair is successful.

Remote radio frequency(RF) link method:
Pair and clear up the RF code

  1. How to pair the RF code
    1.1 (can be turned on and off): before operations.
    Press the switch button for about 8 seconds until you hear Di-Di(2 times).Then the matching of RF code is successful. The key of the remote controller can control the switching of the state of the switch on and off corresponding to the position of the switch.
    1.2 (Open only): Confirm your switch is off before operations.
    Press the switch button for about 5 seconds until you hear Di(1 time). After that, release the button, press the corresponding button on the remote control to turn on. Then the matching of RF codes is successful.
    The key of the remote controller can control the corresponding position of the switch to be open. 1.3 (Close only): Confirm your switch is on before operations.
    Press the switch button for about 5 seconds until you hear Di(1time). After that, release the button, press the correspondin button on the remote control to turn on. Then the matching of RF codes is successful. The key of the remote controller can control  the corresponding position of the switch to be closed.

  2. How to clear up the RF code
    Confirm your switch is off before operations. Press the switch button for a long time until you hear Di-Di-DiDi(4 times), and then release the button.The RF code is now cleared up.

Enter MOES Skill in Alexa APP

  1. Complete product networking configuration in the App
    Complete the device’s networking configuration according to the prompts in the App.
    Note: In the App, change the name of the device to an easily identifiable name such as Alexa; names are usually in English, such as “bed light”.

  2. Configure the Amazon Echo device
    (If you have already configured Amazon Echo, you can skip this step. The following instructions are based on the iOS client.)
    ① Make sure you Amazon Echo device is powered on and connected to a Wi-Fi network.
    ② Open the Alexa APP on your phone and log in
    ③ tap on the menu in the upper left corner of the Home page, select “Settings” and tap “Set Up A New Device” to set up the Amazon Echo.
    ④ Choose your Amazon Echo device type and language for connecting.
    ⑤ Press and hold the small dot on the device until the light turns yellow.
    ⑥ Click “Continue” to connect to the hotspot, connect to the Amazon Echo hotspot, and return to the APP page.
    ⑦ Click “Continue” to find and connect to your home Wi-Fi network.
    ⑧ Amazon Echo will take a few minutes to try to connect to the network.
    ⑨ After the network connection is successful, tap “Continue”. An introduction video will appear,After the video ends,tap “Continue” to jump to the Alexa Home page.
    ⑩ You have now completed the Amazon Echo’s configuration process.

  3. Key step —— Link Skill
    ① Tap on“Skills” in the Alexa App menu.
    ② Then search for “App Name”. Tap “Enable” to enable the Skill.
    ③ Enter the App account and password, then tap “Link Now” to link your App account to enable the Skill. Now you can start your smart home journey

  4. Common commands
    Control the device via voice commands, now you can control your smart device with Echo. You can control your device (such as your bedroom light) with the following commands:
    ● “Alexa, turn on
    ● “Alexa, turn off

SERVICE

Thank you for your trust and support to our products, we will provide you with a two-year worry-free after-sales service (freight is not included), please do not alter this warranty service card, to safeguard your legitimate rights and interests. If you need service or  have any questions, please consult the distributor or contact us.
Product quality problems occur within 24 months from the date of receipt, please prepare the product and the packaging, applying for after-sales maintenance in the site or store where you purchase; If the product is damaged due to personal reasons, a certain  amount of maintenance fee shall be charged for repair.
We have the right to refuse to provide warranty service if:

  1. Products with damaged appearance, missing LOGO or beyond the service term
  2. Products that are disassembled, injured, privately repaired, modified or have missing parts
  3. The circuit is burned or the data cable or power interface is damaged
  4. Products damaged by foreign matter intrusion (including but not limited to various forms of fluid, sand, dust, soot, etc.)

RECYCLING INFORMATION

All products marked with the symbol for separate collection of waste electrical and electronic equipment (WEEE Directive 2012/19 / EU) must be disposed of separately from unsorted municipal waste. To protect your health and the environment, this equipment  must be disposed of at designated collection points for electrical and electronic equipment designated by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences for the environment and human health. To find out where these collection points are and how they work, c ontact the installer or your local authority.

WARRANTY CARD

Product Information
Product Name_
Product Type__
Purchase date_

Warranty Period__
Dealer Information

Customer’s Name__
Customer Phone__
Customer Address

Maintenance Records

Failure date Cause Of Issue Fault Content Principal

Thank you for your support and purchase at we MoesGo, we are always here for your complete satisfaction, just feel free to share your great shopping experience with us.

MoesGo RF433 No Neutral Wire WiFi Smart Touch Wall Light Switch - icon
4

If you have any other need, please do not hesitate to contact us first, we will try to meet your demand.

FOLLOW US

| @moessmart
---|---
| @moes_smart
| MOES.Official
| @moes_smart
| @moes_smart
| www.moes.net

EVATOST CONSULTING LTD
Address: Suite 11, First Floor, Moy Road Business
Centre, Taffs Well, Cardiff, Wales, CF15 7QR
Tel: +44-292-1680945
Email: contact@evatmaster.com

AMZLAB GmbH
Laubenhof 23, 45326 Essen
Made In China

Manufacturer:
YUEQING NOVA ELECTRONICS CO.,LTD
Address: 3th Floor, Building 2, Power Science
and Technology Innovation Center, NO. 238,
Wei 11 Road, Yueqing Economic Development
Zone, Wenzhou, Zhejiang, China
Tel:+86-577-62625592
After-sale Service: service@moesgo.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals