Opticis BR-500 19 1RU Power Supply Frame for Display Port 1.2 Modules User Manual

Opticis BR-500 19 1RU Power Supply Frame for Display Port 1.2 Modules

Product Information

The 19 1RU Power Supply Frame for DisplayPort 1.2 Modules, BR-500, is a modular rack and fiber-optic solution that provides flexibility for installing Opticis DisplayPort 1.2 modules. It can accommodate up to 8 units of DPFX-250-TX or DPFX300-TX. The mounting unit is connected to a central bus power of +12VDC at 4.2A. The BR-500 can be fitted with dual power supplies for load-sharing and redundant backup. It features two LEDs in the front panel to indicate power supply failure and ensure a stable system without disruption or disconnection from power failures.

The BR-500 also has a separate RJ45 port for LAN cable connection, enabling access to the current power status of individual modules and the ability to turn on/off the power of the device. It supports the use of premium graded DisplayPort 1.2 copper cables, allowing extension up to 3m (9.84 feet) from the sources.

Please note that the BR-500 is only compatible with Opticis DisplayPort 1.2 fiber-optic transmitters. DisplayPort modules and DisplayPort copper cables are sold separately. When using a 3m DisplayPort copper cable, it is recommended to use with Lindy (PN: 36483), Kramer (PN: C-DP-10), or StarTech (PN: DISPLPORT10L) products.

The power supply is also sold separately, and two options are available: BR-500-IT (BI060S12F02_Lev:6) – Power Supply for BR-500 (100-240VAC, 50-60Hz) and BR-500-MD (BM060S12F02_Lev:6) – Medical Certified Power Supply for BR-500 (100-240VAC, 50-60Hz).

Shipping group includes: BR-500 (1 unit), Module bracket (8 units), Module Slot (8 units), Heat Sink (16 units), Screw (32 units), and User manual (1 unit).

Product Usage Instructions

WebGUI Control

All primary functions of the BR-500 can be controlled via the built-in WebGUI. The supported web browsers for control are Microsoft Explorer, Microsoft Edge, and Chrome (temporarily not available).

Set up before using GUI

Step 1

1. Connect the Lan-Port of BR-500 with the Lan-Port of PC using a LAN cable.
2. When the PC is connected to the Ethernet, set the Network settings as follows:
   • Select “Use the following IP address”.
   • Set the IP address as: 192.168.11.3
   • Set the Subnet mask as: 255.255.255.0
   • Set the Default gateway as: 192.168.11.1
   • Select “Use the following DNS server addresses”.
   • Set the Preferred DNS server as: 8.8.8.8
   • Click “OK” to finish the setting.

Step 2: Open a web browser that is either Microsoft Explorer or Microsoft Edge.

1. Type the IP address 192.168.11.2 into the web address entry bar.
2. Press Enter.

Note: The first screen that appears allows you to check the current status of BR-500 channels. Control is only available when logged in, and a password is not required to log in.

Welcome

Congratulations on your purchase of the 19” 1RU Power Supply Frame for DisplayPort 1.2 Modules, BR-500. This manual contains information that will assist you in installing and operating the product.

Product Description

The 19” 1RU multi-mounting rack, BR-500 is a modular rack and systematic fiber-optic solution providing flexibility to install Opticis DisplayPort 1.2 modules up to 8 units. DPFX-250-TX, or DPFX-300-TX is required in use. Each power line of mounting unit is connected to the central bus power of +12VDC at 4.2A. BR-500 can be fit with the dual power supplies for load-sharing and redundant backup. BR-500 adopts two (2) LEDs in the front panel for power supply failure to run the stable system without any disruption or disconnection from the power failure.

BR-500 has one separate RJ45 Port which allows the connection through LAN cable. This connection to GUI enables the access to the current power status of individual module and also allows to turn on/off the power of the device. By using premium graded DisplayPort 1.2 copper cables, BR-500 can extend up to 3m (9.84feet) distance from the sources.

Note: BR-500 is applicable to use with Opticis DisplayPort 1.2 fiber- optic transmitters only.

• The DisplayPort modules and 2m DisplayPort copper cables are separately sold. BR-500 is recommending to use with the following products when using 3m DisplayPort copper cable.
  • Lindy (PN: 36483)
  • Kramer (PN: C-DP-10)
  • StarTech (PN: DISPLPORT10L)

The Power Supply is separately sold. Please refer to the available options below

1. BR-500-IT (BI060S12F02_Lev:6): Power Supply for BR-500 (100-240VAC, 50-60Hz)
2. BR-500-MD (BM060S12F02_Lev:6): Medical Certified Power Supply for BR-500 (100-240VAC, 50-60Hz)

Shipping group

• BR-500: One (1) unit
• Module bracket: Eight (8) units
• Module Slot: Eight (8) units
• Heat Sink: Sixteen (16) units
• Screw: Thirty-two (32) units
• User manual: One (1) unit

WebGUI Control

All primary functions of BR-500 are controllable via the built in WebGUI. The Web Browser that are capable in controlling are: Microsoft Explorer, Microsoft Edge, and Chrome (temporarily not available).

Set up before the use of GUI

Step 1: Connect the Lan-Port of BR-500 with the Lan-Port of PC by using a Lan cable. When PC is connected to the Ethernet, set the Network setting as follows:

1. Select “Use the following IP address”
2. Set the IP address as: 192.168.11.3
3. Set the Subnet mask as: 255.255.255.0
4. Set the Default gateway as: 192.168.11.1
5. Select “Use the following DNS server addresses”
6. Set the Preferred DNS server as: 8.8.8.8
7. Click “OK” to finish the setting.

Step 2

• As mentioned above, open a web browser that is either Microsoft explorer or Micro edge.
• Type the IP address “192.168.11.2” into the web address entry bar. Then press Enter.

Note: The first screen that appears allows to check the current status of BR-500 channels. Control is only available when logged in. Password is not required to log in.

Step 3: When logged in, the control of the power is available.

1. Main Power: Click “Main Power” button to turn On or Off.
2. Status of the Channel: It shows the status of each channel. Green light is when the power is on, and it means the device is well connected to the input. Gray light is on when the power is off or when the input is disconnected.
3. CH Power: Each channel can be On and Off individually.
   • Note: When the CH power is turned off, and removed the product power, or turn on or off GUI main power, CH power will remain on or off. The CH power will maintain from the recent setting option.
   • Ex): If CH power is Off when the main power is turned on, the CH power will remain Off.
   • If CH power is On when the main power is turned on, the CH power will remain On.

Installation

Important: Please keep the installation procedure below. Improper or no operation may result if the start-up sequence is not correctly followed.

• Step 1: Carefully unpack the contents in the shipping group and prepare DisplayPort modules which will be connected to BR-500.
• Step 2: Turn to the back side of the DisplayPort module and remove top two (2) screws.
• Step 3: Carefully place the push button of the DisplayPort module first to the bracket provided. The push button of the module MUST be pushed by the little bump of the bracket so that the latches can be crawled inside. Make sure that the top line of the housing is aligned with the bracket so that the head of the module can be perfectly fit in to the BR-500 port.
• Step 4: Attach the slot on top to close the module inside the bracket. Make sure that the curved part at the bottom is directed upward as shown in Fig 3. Then insert the two screws that had been removed in “Step 2” back to the same place, passing through the slot.
• Step 5: Turn the bracket facing up, and tighten the rest screws (4) into the bracket.
• Step 6: Stick the two (2) Heat sinks on the bottom of Module bracket. Make sure you align perfectly with the bottom screw holes so that it has enough space to be installed to BR-500.
• Step 7: Mount the Module bracket on BR-500 and connect optical cable to each DisplayPort module.
• Step 8: Connect the premium graded DisplayPort 1.2 copper cable to the DisplayPort receptacles in front of BR-500 device.
  • Opticis has tested several trials with different copper cables including (Startech, Kramer, and Lindy-Anthra line). We recommend to use Display 1.2 copper cable up to 3 meters (9.84ft).
• Step 9: BR-500 offers two power inputs BI050S12F02 for your preference. Connection with one power cable is still enough for the operation. BR-500 offers dual-power supply for load-sharing and power redundancy.

Contact

OPTICIS HQ

• Opticis Co., Ltd.
• 3F, 305, Sanseong-daero, Sujeong-gu Seongnam-si, Gyeonggi-do, 13354 South Korea
• Tel: +82 (31) 719-8033
• Fax: +82 (31) 719-8032
• www.opticis.com
• tosales@opticis.com

For order support, please contact your Distributor or Reseller.
For technical support, check with the Opticis website www.opticis.com or contact techsupp@opticis.com

© 2022 Opticis Co., Ltd. All Rights Reserved

References

• 옵티시스 (Opticis) | 비디오 및 오디오 광링크 솔루션

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>