earfun K2 Kids Bluetooth Headphone

earfun K2 Kids Bluetooth Headphone

Packages

• Wireless headphones

• User manual

• 3.5mm audio cable

• Charging cable

Diagram

Power On/Off

1. Power ON:
   Press and hold the “II” button for 2s. The blue light will turn on and then go out, and you will hear a voice prompt “power on”.

2. Power OFF:
   Press and hold the “II” button for 5s. The red light will turn on and then go out, and you will hear a voice prompt “power off”.

How to pair for the first time

Step 1:

Step 2:

1. Press and hold the ” button for 2s to power on, then the red and blue lights will flash alternately to enter the pairing mode. You will hear a voice prompt “Pairing”.
2. Enable the Bluetooth of your cellphone and find “EarFun K2 ‘to connect. Once paired, you will hear “Connected

Answer / Hang up/Redial/Reject a call

Volume Control/Music Control

Clear Paring Record/Reset

With your headphones powered on, press and hold the “+” and “-” buttons simultaneously for 5s, until the red and blue lights flash 3 times, and the headphones have entered pairing mode again.

Charging Indications

1. In charging: red light stays on
2. Full Charge: blue light stays on (charging for 2.5 hours)

Toggle volume limit operation

Simultaneously press and hold the “+” and “-” buttons once to switch between the two volume limit modes: learning mode(85dB) and travel mode(94dB).

Kind Remider: The headphones will automatically turn off after 5 minutes of being disconnected from any device.

Bluetooth Indicator Light & Voice Indication

FCC Statement

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device. pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

RF Exposure Compliance
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

CAUTION
Risk of explosion if the battery is replaced by an incorrect type Disposal of a battery into fire or a hot even, or mechanically crushing or cutting of a battery, that can result in an explosion;

Leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas:

A battery subjected to extremely low air pressure that may result in an explosion or the leakage of flammable liquid or gas.

To prevent possible hearing damage, do not listen at high volume levels for long periods.

BLUETOOTH

The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Earfun Technology (HK) Limited is under license.
Other trademarks and trade names are those of their respective owners.

EU Declaration of Conformity
Earfun Technology (HK) Limited hereby declares that this equipment is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU and RoHS 2011/65/EU Directive. The declaration of conformity may be consulted in the support section of our Web site, accessible from www.myearfun.com

UK Declaration of Conformity
Hereby. [Earfun Technology (HK) Limited] declares that the radio equipment type [K2] is in compliance with UK Radio Equipment Regulations (SI 2017/1206). The full text of the declaration of conformity is available at the following internet address: www.myearfun.com

ISED Compliance Statements

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).

Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>