HOOVER FH50700 PowerDash Pet Carpet Cleaner User Manual
- June 14, 2024
- Hoover
Table of Contents
- IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS
- Carton Contents
- Product Guide
- How to Assemble
- Getting Started With Your PowerDash™ Carpet Cleaner
- Maintenance
- EXPERT CARPET SOLUTIONS: PROFESSIONAL GRADE
- PLUS CARPET SOLUTIONS
- HARD FLOOR SOLUTIONS
- Troubleshooting
- SERVICE & WARRANTY
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
HOOVER FH50700 PowerDash Pet Carpet Cleaner User Manual
IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS
When using an electrical appliance, basic precautions should always be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE.
WARNING:
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, DAMAGE OR INJURY:
- Fully assemble before operating.
- Operate vacuum only at voltage specified on data label on back of vacuum canister.
- Do not leave appliance when plugged in. Unplug from outlet when not in use and before cleaning or servicing.
- Do not use outdoors.
- Do not immerse. Use only on carpet moistened by cleaning process.
- To Reduce the Risk of Fire and Electric Shock due to internal component damage, use only HOOVER cleaning fluid intended for use with this appliance. See the Cleaning Fluid section section (page 19) of this manual.
- Do not allow to be used as a toy. Not intended for use by children age 12 and under. Close supervision is necessary when used near children. To avoid injury or damage, keep children away from product, and do not allow children to place fingers or other objects into any openings.
- Use only as described in this manual. Use only manufacturer’s recommended attachments and products.
- Do not use with damaged cord or plug. If appliance is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, take it to a service center prior to continuing use.
- Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or corners. Do not place product on cord. Do not run appliance over cord. Keep cord away from heated surfaces.
- Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
- Do not handle plug or appliance with wet hands.
- Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint, hair and anything that may reduce air flow.
- Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts.
- Turn off all controls before unplugging.
- Use extra care when cleaning on stairs. To avoid personal injury or damage and to prevent the cleaner from falling, always place cleaner at bottom of stairs or on floor. Do not place cleaner on stairs or furniture, as it may result in injury or damage.
- Do not use to pick up flammable or combustible liquids, such as gasoline, or fine wood sandings, or use in areas where they may be present.
- onnect to a properly grounded outlet only. See Grounding Instructions.
- Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
- Do not use without filters and tanks in place.
- Do not clean over floor electrical outlets.
WARNING: This product contains chemicals known to the State of California to cause cancer, birth defects or reproductive harm. WASH HANDS AFTER HANDLING.
GROUNDING INSTRUCTIONS:
This appliance must be grounded. If it should malfunction or breakdown,
grounding provides a path of least resistance for electric current to reduce
the risk of electric shock. This appliance is equipped with a cord having an
equipment-grounding conductor (C) and grounding plug (A). The plug must be
inserted into an appropriate outlet (B) that is properly installed and
grounded in accordance with all local codes and ordinances.
WARNING:
Improper connection of the equipment-grounding conductor can result in the
risk of electric shock. Check with a qualified electrician or service person
if you are in doubt as to whether the outlet is properly grounded. Do not
modify the plug provided with the appliance – if it will not fit the outlet,
have a proper outlet installed by a qualified electrician. This appliance is
for use on a nominal 120-volt circuit and has a grounding plug that looks like
the plug (A) illustrated in Fig. 1. A temporary adapter (D) may be used to
connect this plug to a 2-pole receptacle (E) if a properly grounded outlet is
not available (Fig. 2). The temporary adapter should be used only until a
properly grounded outlet (B) can be installed by a qualified electrician (Fig.
1). The green colored rigid ear, lug, or the like (F) extending from the
adapter must be connected to a permanent ground (G) such as a properly
grounded outlet box cover (Fig. 2). Whenever the adapter is used, it must be
held in place by a metal screw.
NOTE: In Canada, the use of a temporary adapter is not permitted by the
Canadian Electrical Code.
CAUTION:
TO REDUCE THE RISK OF DAMAGE
- Avoid picking up hard, sharp objects with this product, as they may cause damage.
- Store appropriately indoors in a dry place. Do not expose machine to freezing temperatures.
- Do not use sharp objects to clean out hose as they can cause damage.
- To assist in reducing drying time, be certain the area is well ventilated when using detergents and other cleaners with this machine.
- o help prevent matting and resoiling, avoid contact with carpets until they are dry. Keep children and pets away from carpets until they are completely dry.
- Do not store extractor with solution in tanks.
- With brushes and brush roll on, do not allow cleaner to sit in one location for an extended period of time, as damage to the floor can result.
- Do not use this extractor on hard floors. Using this machine on hard floors may scratch or damage your floor.
- Water will drip from the brushes and underside of the product after use and may puddle. To avoid damage to wood and laminate flooring and to avoid potential slip hazard, after use (a) do not leave the product on wood and laminate surfaces and remove to a hard surface and (b) place unit on absorbent material (such as a towel) to soak up drips.
Carton Contents
-
Carpet Cleaner
-
Upper Handle
-
Upper Handle Pole
-
Clean Water Tank
-
Dirty Water Tank
-
Power Spin Brush Roll
-
Sample Bottle of Cleaning Solution
Product Guide
How to Assemble
-
Insert the Upper Handle into the Upper Handle Pole until you hear a “CLICK”.
-
Insert the upper Handle Pole into the base until you hear a “CLICK”.
-
Slide the Clean Water Tank securely into place on the back of the unit. Push down firmly
-
Wrap the power cord around the cord hooks for convenient storage.
Before You Begin Cleaning:
Vacuum carpet and upholstery thoroughly with a Hoover vacuum before use.
Don’t use the carpet cleaner as a traditonal vacuum cleaner.
Use your Hoover carpet cleaner only if upholstery fabric is marked with a “W” (for “wet” clean) or “S/W” (for “solvent/dry” or “wet” clean). Don’t clean fabric marked “S” (“solvent/dry” clean only).
Test for colorfastness in a small, hidden area. Gently rub surface with a dampened white cloth. Wait ten minutes and check for color removal or bleed with a white paper towel.
Move furniture out of area to be cleaned. Place aluminum foil or wax paper under legs of furniture too heavy to move to prevent wood finishes from staining carpet. Pin up furniture skirts and draperies.
Pretreat spots and heavy traffic areas with a Hoover® Cleaning Solution*. See the “Cleaning Solutions” section.
*Available at additional cost if not included with your model.
Pretreating:
For best results, pretreat stains with a Hoover spot treatment (see Hoover Cleaning Solution Guide, pg. 19) to help loosen and remove even the most stubborn stains.
NOTE: To prevent staining, use plastic or aluminum foil to protect wood or metal surfaces from possible water spray.
NOTE: To avoid damage to wood floors underneath area rugs or carpet, place waterproof material (ex: plastic) underneath them before cleaning.
Getting Started With Your PowerDash™ Carpet Cleaner
Fill the Clean Water Tank
-
Remove the Clean Water Tank from the back of the unit.
-
Remove the cap from the bottom and add warm water to the Water fill line.
-
Add Hoover® cleaning solution to the Solution fill line.
-
Replace and tighten cap. Slide the Clean Water Tank back into the unit. Push down firmly.
How to Clean Carpets with your PowerDash™
-
Plug power cord into electrical outlet.
-
Step on the Handle Release Pedal to recline the unit for cleaning position.
-
Step on ON/OFF Pedal to turn ON
-
Squeeze trigger for a slow forward and backward wet stroke*.
-
Release trigger for a slow forward and backward dry stroke*.
IMPORTANT
For full suction, it is important that the Dirty Water Tank is properly
secured before cleaning.
CAUTION
Do not clean over floor electrical outlets. Water will drip from the brushes
and underside of the product after use and may puddle. To avoid damage to wood
and laminate flooring and to avoid potential slip hazard, after use (a) do not
leave the product on wood and laminate surfaces and move to a hard surface and
(b) place unit on an absorbent material (such as a towel) to soak up drips.
Continue using dry strokes until little water is visible passing through the
nozzle.
For best results, Hoover recommends rinsing carpet with water only. This
removes residual carpet cleaning solution. Fill Solution Tank with water and
repeat. For heavily soiled areas, repeat. Avoid saturating carpet.
NOTE: Empty Dirty Water Tank when the motor sound becomes higher pitched and there is a loss in suction (see “Automatic shut-off”). You will also see the float rise and shut off suction at the same time.
Maintenance
How to Empty and Clean your Tanks:
Dirty Water Tank:
-
Turn the cleaner off and unplug from electrical outlet.
-
Press latch and remove Dirty Water Tank from the back of the unit.
-
Carry Dirty Water Tank in an upright position and place on a flat surface.
-
Open Quick Pour Spout and empty
-
Replace and close the Quick Pour Spout.
-
Prior to replacing tank, check and clean filter as needed.
-
Replace Dirty Water Tank by tilting back then rocking it forward to snap into place
IMPORTANT
For full suction, it is important that the Dirty Water Tank is properly
secured before cleaning.
How to Empty and Clean your Tanks:
Clean Water Tank:
-
Remove tank from the unit.
-
Unscrew cap. Empty tank, rinse and allow to air dry
-
Replace the tank once it is clean and dry
How to Clean Nozzle
-
To prevent possible leaking, remove tanks from the unit.
-
Unit should be in upright position.
-
Grip the top of the nozzle and pull up to remove. Lift the unit up slightly to remove nozzle.
-
Rinse the nozzle under running water to remove any dirt or debris. Allow it to dry
-
Replace the nozzle by aligning the tabs at the bottom of the nozzle to the foot.
-
Snap nozzle into place.
Belt Maintenance
HOW TO REMOVE
-
Turn unit off and unplug from electrical outlet.
-
Flip cleaner on its side to expose bottom of cleaner.
-
To remove belt covers, use Philips screwdriver to remove 6 screws. Arrows show location of screws.
-
Remove belt covers from unit.
-
Pull brush roll toward user to 1 remove from unit.
-
Remove belt. Dispose of old belt
HOW TO REPLACE
-
Place new belt on motor shaft.
-
Slip brushroll through belt
-
Position non-belt side end cap of brushroll into pocket.
-
Carefully stretch belt to locate other end cap into pocket, making sure that the end caps are in their correct orientation.
-
Replace belt covers and secure by replacing all 6 screws.
How to Remove and Clean Brushroll
HOW TO REMOVE
-
Turn unit off and unplug from electrical outlet.
-
Flip cleaner on its side to expose bottom of cleaner.
-
To remove belt covers, use Philips screwdriver to remove 6 screws. Arrows show location of screw.
-
Remove belt cover from unit.
-
Pull brushroll toward user to 1 remove from unit.
-
Rinse brushroll and all to dry.
HOW TO REPLACE
-
Slip brush roll through belt.
-
With belt in place, pull and slide brus hroll into unit, making sure that the brus hroll end caps are in correct orientation.
-
Replace belt cover and secure by replacing all 6 screws.
CAUTION
To reduce the risk of injury from moving parts, unplug before servicing.
IMPORTANT
Rotate brus hrolls manually to make sure belt is not twisted or pinched.
STORAGE
Before storing: Empty Clean Water Tank and let air dry. Replace on
cleaner.
Empty Dirty Water Tank, rinse tank and lid thoroughly with clean water and let
air dry.
Allow brushes and underside of carpet cleaner to air dry thoroughly before
storing carpet cleaner on a carpeted or wood surface.
LUBRICATION
The motor is equipped with bearings that contain sufficient lubrication for
the life of the motor.
The addition of lubricant could cause damage. Therefore, do not add lubricant
to motor bearings.
Use only Hoover cleaning solutions to prevent potential harm to your carpet cleaner and keep your warranty.
For best results, use your Carpet Cleaner + Spot Treatment + Solutions.
Hoover has a full line of Detergents and Spot Treatments to complement your Hoover carpet cleaner and the specific condition of your carpet. To prevent project interruption, keep Detergent on hand and store with your carpet cleaner. Spot Treatment may be used as a maltreatment immediately before you clean your carpets, or as an independent treatment between cleaning your carpets.
EXPERT CARPET SOLUTIONS: PROFESSIONAL GRADE
EXPERT CLEAN™ CARPET WASHER DETERGENT
Powerful, professional strength cleaner lifts dirt and removes allergens for
our deepest, extreme clean.
EXPERT CLEAN™ SPOT TREATMENT GEL
Professional grade targeted gel removes tough stains like ground-in dirt,
allergens, chocolate and wine.
EXPERT PET™ CARPET WASHER DETERGENT
Powerful, professional strength enzymes break down biological stains, dirt and
odor for a truly deep clean.
EXPERT PET™ SPOT TREATMENT SPRAY
Professional grade targeted enzyme spray removes tough stains like dirt, oils,
urine and residual odor.
PLUS CARPET SOLUTIONS
CLEAN PLUS™ CARPET WASHER DETERGENT
Powerful cleaner for everyday dirt and grime.
CLEAN PLUS™ SPOT SPRAY
Powerful spot spray for everyday dirt and grime.
PET PLUS™ CARPET WASHER DETERGENT
Powerful cleaner enhanced with enzymes to tackle pet messes and eliminate
odor.
PET PLUS™ SPOT SPRAY
Powerful spot spray enhanced with enzymes to tackle pet messes and eliminate
odor.
PRO PLUS™ CARPET WASHER DETERGENT
Professional strength carpet & upholstery solution removes stubborn stains and
odors.
HARD FLOOR SOLUTIONS
MULTI-FLOOR PLUS™ HARD FLOOR SOLUTION
Powerful hard floor cleaning solution removes everyday dirt and grime.
TILE & GROUT PLUS™ HARD FLOOR SOLUTION
Powerful hard floor cleaning solution cleans and revitalizes tile and grout
surfaces.
STEAM PLUS™ HARD FLOOR SOLUTION
Powerful hard floor cleaning solution combines with steam to safely wash hard
floors.
Need Help?
If you need further assistance:
If your product needs servicing within the warranty period, please contact
Customer Service at 1-800-944-9200;
Mon-Fri 7am-6pm EST. Always identify your carpet washer by the complete model
number when requesting information or ordering parts. (The model number of the
carpet washer is located on the data plate).
PLEASE DO NOT RETURN THIS CLEANER TO THE STORE.
Troubleshooting
Any other servicing should be done by an authorized service representative.
USE TROUBLESHOOTING GUIDE AS A FIRST STEP TO RESOLVE ANY PROBLEMS YOU MAY
BE EXPERIENCING.
If appliance is not working as it should, has been dropped, damaged, left
outdoors, or dropped into water, call Customer Service at 1-800-944- 9200 for
further instruction before continuing use.
WARNING
To reduce the risk of personal injury – Unplug before cleaning or servicing
QUESTIONS OR CONCERNS?
Contact Us:
1-800-944-9200
If you have any questions or, visit Hoover.com or connect with us:
Twitter: @HooverUSA
Facebook: facebook.com/hoover
Do not return to store. See back of product for model number.
PROBLEM | POSSIBLE CAUSE | POSSIBLE SOLUTION |
---|---|---|
Cleaner won’t run |
- Not firmly plugged in
- No voltage in wall plug
- Blown fuse or tripped breaker
- Fuse in cleaner blown
|
- Plug unit in firmly
- Check fuse or breaker in home
- Replace fuse or reset breaker in home
- Take to service center
Low suction|
- Dirty Water Tank full/automatic shut off engaged
- Dirty Water Cap or Plug not on correctly
- Dirty Water Tank Debris Filter Clogged
- Blockage in nozzle
- Recovery Tank not properly secured
- Clogged Filter
|
- Remove and empty Dirty Water Tank. See “How to Empty” page 12
- Tighten
- See “How to Clean” page 124. See “How to Clean” page 13
- Replace Recovery Tank and secure recovery tank latch
- Clean it
Clean water won’t dispense|
- Clean Water Tank not firmly in place
- Clean Water Tank or solution container empty
| 1. Make sure tank is securely locked in position2. Refill container
according to cleaning instructions3. Ensure trigger is being pulled
Brushes won’t rotate during floor cleaning| | Check for jams and/or broken
belt
SERVICE & WARRANTY
SERVICE INFORMATION
ANY SERVICING SHOULD BE DONE BY AN AUTHORIZED SERVICE REPRESENTATIVE CALL
1-800-944-9200 USA & CANADA
In the event that further assistance is required, visit an authorized service
center. Find one nearest you by visiting our website at
www.hoover.com. Costs of any transportation to and
from any place of repair are to be paid by the owner. Always identify your
product by the model number and manufacturing code when requesting information
or ordering replacement parts.(The model number and manufacturing code are on
the back of the product).
LIMITED ONE YEAR WARRANTY (DOMESTIC USE) WHAT THIS WARRANTY COVERS
When used and maintained in normal household use and in accordance with the
Owner’s Manual, your HOOVER® product is warranted against original defects in
material and workmanship a full year from date of purchase (the “Warranty
Period”). During the Warranty Period, Hoover® will provide labor and parts at
no cost to you to correct any such defect in products purchased in the United
States, U.S. Military Exchanges and Canada.
HOW TO MAKE A WARRANTY CLAIM
If this product is warranted, take or send the product to either a Hoover®
Sales and Service Center or Hoover® Authorized Warranty Service Dealer along
with proof of purchase. For an automated referral to authorized service
outlets in the U.S.A., phone:
1-800-944-9200 OR visit Hoover® online
at www.hoover.com. For additional assistance or
information concerning this Warranty or the availability of warranty service
outlets, call the Hoover® Consumer Response Center, Phone 1-800- 944-9200,
Mon-Fri 8am-7pm EST. In Canada, contact Hoover® Canada, Carson Building, 100
Carson St., Etobicoke, Ontario M8W 3R9, Phone:
1-800-944-9200, Mon-Fri 8am-7pm EST.
WHAT THIS WARRANTY DOES NOT COVER
This warranty does not cover: use of the product in a commercial operation
(such as maid, janitorial and equipment rental services), filter, brushroll
and belt, improper maintenance of the product, damage due to misuse, acts of
God, nature, vandalism or other acts beyond the control of Hoover®, owner’s
acts or omissions, use outside the country in which the product was initially
purchased and resales of the product by the original owner. This warranty does
not cover pick up, delivery, transportation or house calls, however, if you
mail your product to a Hoover® Sales and Service Center for warranty service,
cost of shipping will be paid one way.
This warranty does not apply to products purchased outside the United States, including its territories and possessions, outside a U.S. Military Exchange and outside of Canada. This warranty does not cover products purchased from a party that is not an authorized retailer, dealer, or distributor of Hoover® products.
OTHER IMPORTANT TERMS
This warranty is not transferable and may not be assigned. This Warranty shall
be governed and construed under the laws of the state of Ohio. The Warranty
Period will not be extended by any replacement or repair performed under this
Warranty.
THIS WARRANTY IS THE EXCLUSIVE WARRANTY AND REMEDY PROVIDED BY HOOVER®. ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR PARTICULAR PURPOSE, ARE DISCLAIMED. IN NO EVENT WILL HOOVER® BE LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND OR NATURE TO OWNER OR ANY PARTY CLAIMING THROUGH OWNER, WHETHER BASED IN CONTRACT, NEGLIGENCE, TORT OR STRICT PRODUCTS LIABILITY OR ARISING FROM ANY CAUSE WHATSOEVER. Some states do not allow the exclusion of consequential damages, so the above exclusion may not apply to you. This warranty gives you specific rights; you may also have others that vary from state to state.
Register your carpet cleaner by:
Visiting Hoover.com or Hoover.ca
Calling 1-800-944-9200
References
- Hoover Canada
- Vacuum Cleaners | Carpet Cleaners | Hard Floor Cleaners | Hoover
- Vacuum Cleaners | Carpet Cleaners | Hard Floor Cleaners | Hoover
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>