HOOVER F3860-1-011 Floor Polisher User Manual
- October 30, 2023
- Hoover
Table of Contents
HOOVER F3860-1-011 Floor Polisher User Manual
INSTRUCTIONS FOR SAFE USE
This appliance should only be used for domestic cleaning, as described in this
user guide. Please ensure that this guide is fully understood before operating
the appliance.
Do not leave the appliance plugged in. Always switch off and remove the plug
from the socket after use, or before cleaning the appliance or any maintenance
task.
This appliance can be used by children aged from 8 years and above and persons
with reduced physical, sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or instruction concerning
use of the appliance in a safe way and understand the hazards involved.
Children shall not play with the appliance. Cleaning and user maintenance
shall not be made by children without supervision.
If the power cord is damaged stop using the appliance immediately. To avoid a
safety hazard, an authorised Hoover service engineer must replace the power
cord.
Keep hands, feet, loose clothing and hair away from rotating brushes.
Use only attachments, consumables or spares recommended or supplied by Hoover.
This Polisher must not be used for floor washing.
Do not use your appliance out of doors or on any wet surface or for wet pick
up.
Do not pick up hard or sharp objects, matches, hot ashes, cigarette ends or
other similar items.
Do not spray with or pick up flammable liquids, cleaning fluids, aerosols or
their vapours.
Do not run over the power cord when using your appliance or remove the plug by
pulling on the power cord.
Do not continue to use your appliance if it appears faulty. Hoover service: To
ensure the continued safe and efficient operation of this appliance we
recommend that any servicing or repairs are only carried out by an authorised
Hoover service engineer.
Do not stand on or wrap the cord around arms or legs when using your
appliance.
The Environment:
This appliance is marked according to the European directive 2011/65/EC on
Waste Electrical and Electronic Equipment (WEEE). By ensuring this product is
disposed of correctly, you will help prevent potential negative consequences
for the environment and human health, which could otherwise be caused by
inappropriate waste handling of this product. The symbol on the product
indicates that this product may not be treated
as household waste. Instead it shall be handed over to the applicable
collection point for the recycling of electrical and electronic equipment.
Disposal must be carried out in accordance with local environmental
regulations for waste disposal. For more detailed information about treatment,
recovery and recycling of this product, please contact your local city office,
your household waste disposal service or the shop where you purchased the
product
This product complies with the European Directives 2014/35/EU, 2014/30/EU and 2011/65/EU
CANDY HOOVER GROUP S.r.l. Via Privata Eden Fumagalli, 20861 Brugherio (MB) Italy
GETTING STARTED
By following this step-by-step guide your new Hoover polisher will be ready
for use:
Remove polisher and accessories from packaging.
Please dispose of the packaging in a safe and environmentally conscientious
way.
HANDLE ASSEMBLY
Join together the 2 handle sections ensuring that the stud locates in the
hole. (Fig. 1)
Fit the handle into the socket at the rear of the hood and push until it locates in the hole (indicated by a “click”). (Fig. 2)
OUTER BAG ASSEMBLY
Attach bag support to the hook positioned under the hand grip. (Fig. 3)
Once the bag support is attached, insert plastic flange at the bottom of bag into the opening located at the rear of the hood. (Fig. 4)
**FITTING THE PAPER DUST BAG**
Refer to the following instructions for models equipped with paper dust bag:
-
Open fastener on outer bag to the fullest extent to expose the air-duct.
-
Fit paper dust bag by pushing the cardboard collar on the air-duct. (Fig.
-
Tuck paper dust bag into the outer bag and fully close the zip fastener.
FITTING BRUSHES
SAFETY WARNING: The polisher must be switched off and the plug disconnected
from the electrical supply before fitting or changing the brushes.
Turn the polisher upside down. Place each brush or pad on its axle and press
until a click indicates that it is the correct position. To remove brushes or
pads, grasp them and pull towards you. (Fig. 6)
Your polisher is now ready for use.
USING YOUR CLEANER
Ensure the handle is in the upright position before inserting the plug into
the electricity supply.
To start the polisher push the handle down then lower it into the working
position.
To stop the polisher simply return handle to the upright position.
ACCESSORIES
Polishers are equipped with spring loaded brushes and pads in order to obtain
the best results even on floors with uneven surface.
For this reason, the small narrow brush positioned on the front of the hood is
also spring loaded.
Three kits of brushes and pads are supplied with the polisher:
Yellow Hard Bristle Brushes
To be used to remove the old polish then to spread the new wax evenly on the
floor. Particularly suitable for marble and tiles.
Black Soft Bristle Brushes
Must be used to complete the first polishing phase. Suitable for all hard
floors.
Grey Buffing Pads
To be used during the final polishing phase for producing a high gloss.
They can be used on all hard surfaces, but are especially suitable for marble
and tiles.
Natural White Pads
These natural white pads, made mainly of wool, have been especially designed
to polish wooden floors. They should be used after the Black soft brushes.
TO WAX AND POLISH THE FLOORS
TO WAX THE FLOORS:
Before applying polish, ensure that the surface is clean. Remove any greasy
stains using a damp cloth.
To apply the polish, follow the instructions supplied with the polish.
Use a good quality polish, spreading it evenly. After the polish has dried,
polish the floor with the yellow hard texture brushes or the softer black
brushes.
TO POLISH THE FLOORS:
For producing a high gloss, use the natural white pads for wooden floors or
grey buffing pads for all other hard surfaces.
To obtain better results, always move the polisher in straight lines rather
than in circles.
Buffing pads should only be used after the whole surface has first been
polished with brushes.
EMPTYING OUTER BAG / PAPER DUST BAG
The suction polisher collects dust in the bag. To maintain the efficiency of
your polisher check the dust level and empty the cloth bag or replace the
paper dust bag frequently.
MODELS EQUIPPED WITH PAPER DUST BAG:
Fully open zip fastener and remove paper dust bag by pulling the cardboard
collar from the air duct. (Fig. 5)
Fit new paper dust bag as described in paragraph “Fitting the paper dust bag”.
MODELS EQUIPPED WITH CLOTH BAG (WITHOUT PAPER DUST BAG):
Remove the cloth bag from upper plastic clip (Fig. 7)
and disconnect bottom plastic flange from hood pressing lightly on the indent
on the flange.
Turn cloth bag upside down and shake gently. (Fig. 8)
The cloth bag can be washed. We suggest hand washing it in warm water with a mild detergent.
CLEANING BRUSHES AND PADS
Brushes may be washed in warm water with a mild detergent.
Pads may be gently brushed with soapy water and wiped with a damp cloth. Do
not immerse the pads in the soapy water.
Allow the pads to dry thoroughly before use, keeping them flat.
TRANSPORT, MAINTENANCE AND STORAGE
Move the polisher by means of the rear wheels.
Wind supply cord around the 2 clips on the handle tube.
To maintain brushes in good condition, always remove them before storing the
polisher.
SIMPLE USER CHECK LIST BEFORE CALLING FOR SERVICE
- Is there a working electricity supply to the polisher? Check with another appliance.
- Is the dust bag full? Please refer to chapter “Fitting the Paper Dust Bag”.
Please remember: A service charge will be made if the polisher is examined and
found to be in working order, has not been assembled in accordance with these
instructions, or has been
misused.
HOOVER SPARES AND CONSUMABLES
Always replace parts with genuine Hoover spares. These are available from your
local
Hoover dealer or direct from Hoover. When ordering parts always quote your
model number.
HOOVER SERVICE
Should you require service at any time, please contact your local Hoover
Service Office.
QUALITY
BSI ISO 9001: Hoover’s factories have been independently assessed for quality.
Our products are made using a quality system which meets the requirements of
ISO 9001.
YOUR GUARANTEE
The guarantee conditions for this appliance are as defined by our
representative in the country in which it is sold. Details regarding these
conditions can be obtained from the dealer from whom the appliance was
purchased. The bill of sale or receipt must be produced when making any claim
under the terms of this guarantee.
Subject to change without notice.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>