KATIO KADIO C1KPEE4M5HL Dog Grooming Vacuum Kit Instructions

Pet Grooming Kit
Instruction

C1KPEE4M5HL Dog Grooming Vacuum Kit

Thank you for choosing Katia Kadin
Before using, please read all instruction thoroughly.

IMPORTANT SAFETY INSTRUCTIONS

When using an electrical appliance, basic precautions should always be followed, including the following :
READ ALL INSTRUCTIONS BEFORE USING (THIS APPLIANCE)
WARNING – To reduce the risk of fire, electric shock, or injury:
(a) : Do not leave appliance when plugged in. Unplug from outlet when not in use and before servicing.
(b) : Do not use outdoors or on wet surfaces.
(c) : Do not allow to be used as a toy. Close attention is necessary when used by or near children.
(d) : Use only as described in this manual. Use only manufacturer’s recommended attachments.
(e) : Do not use with damaged cord or plug. If appliance is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, return it to a service center.
( f ) : Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or corners.
(g) : Do not run appliance over cord.
(h) : Keep cord away from heated surfaces.
(i) : Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
( j) : Do not handle plug or appliance with wet hands.
(k) : Do not put any object into openings. Do not use with any opening blocked. Keep free of dust,lint, hair, and anything that may reduce air flow.
( l ) : Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts.
(m) : Turn off all controls before unplugging.
(n) : Use extra care when cleaning on stairs.
(o) : Do not use to pick up flammable or combustible liquids, such as gasoline, or use in areas where they may be present.
(p) : Always turn off this appliance before connecting or disconnecting motorized nozzle.
(q) : Unplug before connecting Clipper and other accessories.
( r ) : Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
(s) : Do not use without dust cup and / or filters in place.

SAVE THESE INSTRUCTIONS
To reduce the risk of electric shock, this appliance has a polarized plug (one blade is wider than the other).
This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug.
If it still does not fit, contact a qualified electrician to install the proper outlet.
Do not change the plug in any way.

Quick Setup Guide

Step 1.Disassemble the dust cup and remove all of the accessories.
Disassemble Dust Cup Press the PUSH button and then lift the dust cup in the arrow’s direction.
Assemble Dust Cup

Insert the dust cup in the direction of the arrow. Make sure it’s well fixed.
Step 2: Connect one end of the hose to the vacuum.

Step 3: Connect the other end of the hose to the accessories.

Accessories Part 1: Electric clipper

Electric Clipper Operation Instructions:

1. Trimming function:
   Trimming function: When the Trimming function switch is OFF, shift the switch to the 1st or 2nd gear to turn it on.
   Self-Vacuum function: Press the Self-vacuum function button once to start the 1st gear (1 light on). Press the button 2nd time to start the 2nd gear with stronger suction (2 lights on). Press the button the 3rd  time to turn off the self-vacuum function (light off ).
   (Note: Self-vacuum function could not work when the Trimming function is off.)

2. Power Display:
   1. When the clipper is charged, it could not work. The LED power display will flash from 0 to 99, and it will stay lit with “–” when the battery is fully charged.
   2. When the battery is lower than 20%, the LED power display will flash.
   3. When the power is run out, the LED power display “00”, clipper will stop working.

3. Trouble shooting:
   1. The LED power display “E0”, and the clipper does not work.
   —Please turn off the clipper （Push the Trimming function switch to OFF),and restart it.
   2. Could not turn on the clipper.
   —Battery runs out. Please charge it.
   3. The LED power display “E1”, and the clipper does not work .
   —Restore the normal temperature, and turn off the clipper .
   (Push the Trimming function switch to OFF),and restart it.

Specifications
Electric Clipper:

1.1 According to different needs of hair style to choose guard comb.
(optional use)

1.2 Choose Clipper Mode
Strong Suction Mode
(Need to connect the clipper to the vacuum machine.)
Install strong suction upper cover to the clipper, and switch the trimming function button only. Turn on the vacuum machine for suction.

Self-Vacuuming Mode
(only for trimming a small amount of hair.
No connection to the vacuum cleaner is required.)
Install the clipper’s self-suction upper cover. Press the self-vacuum button and the trimming function button to activate the clipper’s self-suction.
Use a small blade for trimming on special areas like the paws or ears.

Accessories Part 2: Combo Accessories Kit

Install Part B to Part A:
Make sure the fixed button of Part A is unlocked before installation. Align the bottom of Part B to the slots of Part A, press down Part B and you will hear a click if it has been well fixed.

1. Slicker Brush
   Dander, filth, tangled hair, and loose hair from your adorable pets are all easily removed.

2. De-shedding Brush
   Quickly removes loose hair.

3. De-matting Brush
   Gently eliminates tangles, knots, dander, and trapped dirt. Tips: Be careful with the blade part.

4. Silicone Brush
   Effectively removes pet hair from your clothes, sofa, and bed…

5. Cleaning Brush
   Clean hair from clothes or clean the paws of your pet after walking.

Accessories Part 3: Nozzle

Easily cleans dirt and pet hair from sofa, carpet, keyboard, also hair clipper.

Step 4:Plug in the power and turn on the device.

Press the power button to start (default 2nd gear). Press the” + ” ” -“button to switch the gear.

Care & Maintenance

Clean Dust Cup

1. Pull the snap buckle outward to open and empty the dust cup.
2. Use paper or dry towel or clean water to clean dust cup.

Warnings:

• Be careful to take out or install the dust cup.
• Dust cup must be dried before installation back into the machine. Wet dust cup may cause short circuits and machine malfunctions

Specification

Clean Heap

• Remove the dust cup and take out HEPA.
• Clean HEPA and sponge filter with water.
• Dry it in a ventilated place for at least 24 hours.
• Install HEPA back into the machine after it is completely dry.

Notes:

• HEPA should be cleaned at least every other month.
• Do unplug the power before cleaning.
• HEPA and dust cup must be dried before installation back into the machine.
• Undried HEPA can cause short circuits and machine malfunctions.

Parts & Accessories

Clean Electric Clipper
Push outward to remove the blade.
Align the bottom of the blade with the slot and press inside to install the blade. Suction the debris from the blade and clipper. Drop some lubricant(not included) on the blade.

Trouble Shootings

□ Stuck Filter
□ Hose/Attachment has not been well installed.| □ Check the hose.
□ Clean the filter as instruction.
□ Install the hose or adapter properly.
Vacuum Stops Working Suddenly| □ Overheating protection| □ Please unplug and wait for the temperature drops.
Electric Clipper Produces Weird Noises| □ Clippings stuck blade| □ Clean the blade as instruction
□ Drop the appropriate amount of lubricating oil.

Warranty

1. 12 months warranty from the purchase date. Limited free repair for the purchased product. Consumables and accessories are not subject to warranty.

2. Within the warranty period, if the machine is damaged or malfunctions during general use, it will be repaired free of charge. If it cannot be repaired, a replacement will be provided.

3. The following conditions are paid repairs even during the warranty period:
   ①Damage caused by misuse or carelessness.
   ②Damage in transit.
   ③Damage caused by pets (biting, scratching, etc.).
   ④Damage caused by fire, flood, earthquake, hurricane or other natural disasters.
   ⑤Damage during use other than general household use (long-term commercial use, etc.).

4. This warranty does not cover any of the following conditions:
   ① Product purchased from sales channels without authorization (secondary market, auctions, etc.).
   ②Disassembles or repairs the product without permission.
   ③Consumables and accessories.

5. Shipping costs will be borne or reimbursed by us when the product is covered by warranty service.
   However, cost of packaging materials will not be covered.

6. If it is not covered by the warranty, shipping costs and repair fees will be charged when returning.

7. The warranty period of the replacement product is based on the original order’s warranty.

8. Repair or replacement is only valid in certain countries or areas.

9. Please contact us for further guidance if any issues.

10. Warranty terms may be updated without notice. We reserve the right to it.

All repairs and replacement services will be handled under the latest warranty terms.

Service Email: support@katiokadio.com

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>