YIS Marine AOS3066A 6P Membrane Control Panel With Backlight Module And APP Control Instruction Manual
- June 14, 2024
- YIS Marine
Table of Contents
AOS3066A 6P Membrane Control Panel With Backlight Module And APP Control
Product Information:
The 6P Membrane Control Panel with Backlight Module and APP
Control is an ultra-compact panel that is 60% smaller than
traditional panels. It features a PET membrane touch panel
faceplate and has built-in resettable fuses for circuit protection.
Each branch of the panel has a 10A self-resettable fuse. The panel
also has an ON-indication LED and a backlight module for easy
operation in darkness. It has a very low standby current and is
programmed to be momentary, making it ideal for horn or wiper
applications. The package includes a set of 60 assorted graphic and
text label stickers.
The panel has the following specifications:
- Panel Rating: Max Cumulative Amp – 35A
- Voltage Rating: DC 11 – 30V
- Notes: IP66 (Membrane Panel)
- Power Terminals: M4 stud size Ring terminals
- Load Terminals: .250 Quick Terminals (Male)
Product Usage Instructions:
-
Place the provided template on the desired panel position on
the dashboard and cut a hole accordingly. -
From the back of the dashboard, insert the micro USB plug to
the front and connect it to the socket at the back of the
panel. -
Mount the panel firmly onto the dashboard using the
self-adhesive on the back. -
Install the Control Box properly using the included
screws. -
Insert the other end of the micro USB cable into the Control
Box and squeeze the cable into the strain relief hook. -
Crimp the DC positive wire (+) with the included round
terminal, pass it through the included insulator, and connect it to
the screw terminals. Cover the terminals with the insulator
properly. -
Crimp the DC negative wire (-) with the insulated 0.250 female
terminal and insert it into the negative quick terminal on the
Control Box. -
Connect the load terminals to the desired devices. The numbers
on top of the load terminals correspond to the numbers on the
membrane touch panel. -
To set up a specific button to be momentary (Push-On), press
and hold the backlight button to enter setup mode. The white
backlights will blink. Press the desired button to enable momentary
function on it, press again to disable. The ON-indication LED will
blink for Momentary buttons and stay ON for normal buttons during
setup mode. Release the backlight button to exit setup mode. -
To pair with your cellphone, follow the instructions provided
on the back side of the panel.
6P Membrane Control Panel with Backlight Module and APP Control
Installation Instructions
1 1
91
Place the template provided on the
desired panel position and cut the
hole accordingly.
7 5 37.50
2
Cut hole here
3
ø15
Panel position
Dashboard
4
2
To power source
1 Membrane Control Panel 2 Backlight ON/OFF Switch 3 Micro USB Cable 4 Remote
Control Box
Terminals to the devices
Panel back
From the back of dashboard, insert the micro USB plug to the front. Connect the micro USB plug to the socket to the back of panel.
Dashboard
Features
3
Ultra Compact panel size (60% smaller than traditional
panels)
Easy to install no mounting depth, minimum hole drilling
Flexible wiring Control Relay Box installed 1m away from
the touch panel
IP67 protection against strong water jets (Panel Only)
ON-indication LED / 10A Self-resettable fuse for each branch 4
Backlight module allowing easy operation in darkness
Very low standby current
Programmable momentary button all buttons can be
programmed to be momentary (ideal for horn or wiper
applications)
60pcs Assorted Graphic and Text labels stickers set included
Specifications
Faceplate | PET membrane touch panel
Circuit Protection | Built-in Resettable Fuse (PPTC)
Switch Ratings | 10A per branch
5
Panel Rating | Max Cumulative Amp: 35A
Voltage Rating | DC 11 – 30V
Notes | IP66 (Membrane Panel)
Power Terminals | M4 stud size Ring terminals
Load Terminals | .250 Quick Terminals (Male)
Actual Panel Size
Cut hole here
to Device #1~#6
123 456
Mount the panel firmly onto the dashboard with self-adhesive in the back.
Install the Control Box properly with the included screws.
Insert the other end of the micro USB cable into the Control Box. Squeeze the
cable into the strain relief hook on the box as illustrated.
Crimp the DC positive wire (+) with the included round terminal. Pass the wire
through the included insulator and connect to the screw terminals. Cover the
terminals with the insulator properly. Crimp the DC negative wire (-) with the
insulated 0.250″ female terminal and insert into the negative quick terminal
on Control Box.
Connect the load terminals to the desired devices.The numbers on top of the
load terminals correspond to the numbers on the membrane touch panel as shown
in the left.
6
2. Press desired button to setup
123
This template is provided to help you install the membrane panel correctly. Cut out template and trace onto the dashboard. Then drill a hole at the shielded area.
456
1. Press and hold
*All buttons can be set to be momentary; only 1 momentary button can be pressed at the same time.
(See back side for instruction to pair with your cellphone)
(Momentary Button Set-up) To set up a specific button to be momentary (Push-
On), press and hold the backlight button to enter setup mode (white backlights
will be blinking). Press the desired button to enable momentary function on
it, press again to disable. The ON-indicatigon LED will be blinking for
Momentary buttons and stays ON for normal buttons during setup mode. Release
the backlight button to exit setup mode.
2 0 22.03.R e v.0
How to Pair
1
2
My Control Panel
DOWNLOAD APK
ON
ON
GPS
3
4
5
Password: 0000
1 Buttons #1~#6 (Customizable in Settings)
1
2 Switching between different control boxes
3 Current device | Connection Status
4 System voltage monitor
5 Settings
2
CH9141BLE2U | Connected
DC 12.4V
3
4
5
2 0 22.03.R e v.0
FCC Warning Statement
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment. This
equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures: — Reorient or relocate the receiving antenna. —
Increase the separation between the equipment and receiver. — Connect the
equipment into an outlet on a circuit different from that to which the
receiver is connected. — Consult the dealer or an experienced radio/TV
technician for help.
FCC Radiation Exposure Statement The antennas used for this transmitter must
be installed to provide a separation distance of at least 20 cm from all
persons and must not be co-located for operating in conjunction with any other
antenna or transmitter.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1)This device may not cause harmful
interference, and (2)This device must accept any interference received,
including interference that may cause undesired operation.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>